Sharp MX-FWX1 Service Manual ▷ View online
MX-7040N CONFIGURATION 1 – 3
3. Paper feed/Paper exit Option combinations list
: Necessary option
: Necessary option (Use any one of them)
: Necessary option (Use any one of them)
4. Weight list
Weight of each model
*1: Excluding consumable parts.
Necessary option
MX-FN19
MX-FN20
MX-FN21
MX-FN22
MX-FD10
MX-CF11
MX-RB12
MX-RB13
MX-RB14
MX-RB15
MX-LC13
Install
model
model
MX-FN19
MX-FN20
MX-FN21
MX-FN22
MX-TM10
MX-FD10
MX-CF11
MX-RB13
MX-MF11
MX-LC13
MX-PN12
MX-PN13
MX-FN20
MX-FN21
MX-FN22
MX-TM10
MX-FD10
MX-CF11
MX-RB13
MX-MF11
MX-LC13
MX-PN12
MX-PN13
Model name
Weight
Main unit
222kg
*1
MX-FN19
42kg
MX-FN20
72kg
MX-FN21
61kg
MX-FN22
108kg
MX-TM10
32kg
MX-FD10
66kg
MX-RB12
5.7kg
MX-RB13
14.5kg
MX-RB14
27.5kg
MX-RB15
16.4kg
MX-CF11
23kg
MX-LC12
28.5kg
MX-LC13
130.3kg
MX-MF11
21kg
٤
٤
٤
٤
٤
٤
٤
٤
٤
٤
٤
٤
٤
ٌ
٤
ٌ
٤
٤
٤
٤
٤
٤
ٌ
ٌ
٤
ٌ
ٌ
٤
٤
٤
ٌ
MX-7040N MX-6240N/7040N (MAIN UNIT) 2 – 1
MX-7040N
Service Manual
[2] MX-6240N/7040N (MAIN UNIT)
1. Unpacking
A. Unpacking
B. Removal of the fixing tape and protection
material
C. Packed items check
No.
Name
Quantity
1
Waste toner bottle
1
2
Height adjuster plate
4
3
Operation panel
1
4
Operation panel mounting plate
1
5
Operation section cover A
1
6
Operation section cover B
1
7
Wire saddle (S)
2
8
Wire saddle (M)
1
9
Line cable
1
10
Screw (M3 x 8 S-tight)
3
11
Screw (M4 x 8 S-tight)
7
12
Clamp
1
13
Operation Manual
1
1
3
5
6
2
4
8
9
10
12
7
11
13
2
MX-7040N MX-6240N/7040N (MAIN UNIT) 2 – 2
2. Installation
A. Machine height and tilt adjustments
1) Put the height adjuster plate (Packed items) under the adjuster
bolt at the bottom of the machine.
Turn the adjuster bolt to adjust the height and the tilt of the
machine.
MEMO: When the adjuster bolt is turned counterclockwise, the
height is decreased. When turne d clockwise, the height is
increased. (Common to the options the height of which is
adjusted by the adjuster bolt.)
NOTE:
Lower the height of the MX-CF11 to the lowest position
before adjusts the level between the MX-CF11 and the
main body.
Adjust the height of the top surface of main body refer-
Adjust the height of the top surface of main body refer-
ence to the top surface of the MX-CF11.
B. Lock release
(1)
Tray rotation plate lock release
1) Pull out the tray1/2. Remove the screw, and remove the cau-
tion label.
Close the tray which was pulled out.
2) Pull out the tray 3 and tray 4 . Turn the fixing ma terial and
remove it. Remove the caution label.
Attach the removed fixing material to the position shown in the
figure for future use.
Close the tray which was pulled out.
Low
High
MX-7040N MX-6240N/7040N (MAIN UNIT) 2 – 3
(2) Scanner (2/3 mirror unit) lock release
1)
Remove the optical unit fixing screw, and remove the note
label.
label.
C. Attach the operation panel
1)
Attach the operation panel mounting plate (Packed items) to
the operation panel (Packed items), and fix by the screw (M4 x
8 S-tight) (Packed items). Attach the operation section cover B
(Packed items), and fix by the screw (M3 x 8 S-tight) (Packed
items).
the operation panel (Packed items), and fix by the screw (M4 x
8 S-tight) (Packed items). Attach the operation section cover B
(Packed items), and fix by the screw (M3 x 8 S-tight) (Packed
items).
2)
Open the right door.
3)
Remove the screw and remove the upper cabinet front right.
Disconnect the connector from the USB I/F PWB.
Disconnect the connector from the USB I/F PWB.
4)
Remove the screws and remove the front cabinet upper.
5)
Attach the operation panel by fixing the screws (M4 x 8 S-tight)
(Packed items).
(Packed items).
6)
Attach the wire saddle (S) and wire saddle (M), and fix the har-
ness to the wire saddle.
ness to the wire saddle.
NOTE: Check to confirm that the harness does not enter the
panel.
For the reference, refer to the figure below.
For the reference, refer to the figure below.
2
1
3
2
4
2
1
1
1
3
Click on the first or last page to see other MX-FWX1 service manuals if exist.