Sharp MX-FWX1 Service Manual ▷ View online
MX-7040N Transit, Installation (using) environment, Note - i
MX-7040N
Service Manual
Transit, Installation (using) environment, Note
1. Installing (use) conditions
Before installing the machine, c heck that th e following inst alling
(use) conditions are satisfied.
If the installing (use) conditions are not satisfied, the machine may
If the installing (use) conditions are not satisfied, the machine may
not display full performances, resulting in troubles. It may also
cause safety problems. Therefore, be sure to arrange the installing
(use) conditions before setting up the machine.
A. Transportation space
For installation of a large size machine, be sur e to check that the
door size is wide enough before bringing in.
B. Installing space
The following space must be provided around the machine in order
to assure machine performances and proper operations.
If any option is installed, provide the additional space for installing
If any option is installed, provide the additional space for installing
it.
Adequate space must be provide behind the machine for proper
Adequate space must be provide behind the machine for proper
ventilation heat and dust. If not, the machin e cannot exhibit func-
tions against heat and dust, causing some troubles.
C. Power source (Capacity, voltage, frequency,
safety, plug)
If the power specif ications are not satisfied, the machine cannot
exhibit full performances and may cause safety trouble.
Strictly observe the following specifications.
Strictly observe the following specifications.
(1)
Power capacity
The power capacity must conforms to “ 3. Power configuration A.
Indoor wiring (power outlet) and breaker information.”
(2)
Power voltage
Measure the voltage during copying to check that the voltage is in
the range of the specified voltage 10%.
If the voltage is outside the specified range, please have a certified
If the voltage is outside the specified range, please have a certified
electrician upgrade the outlet.
(An electrical work is required.)
Use of a step -up transformer is also available. In this case, the
(An electrical work is required.)
Use of a step -up transformer is also available. In this case, the
capacity must be great enough for the max. power consumption of
the machine.
(3)
Power frequency, waveform
The frequency must be within the range of the specified frequency
2%. If power waveform is deformed, a trouble may occur.
(4)
Safety
Be sure to properly ground the machine.
Grounding (earth connection) must be performed before inserting
Grounding (earth connection) must be performed before inserting
the power plug into the power outlet.
When disconnecting the ear th connection, be sure to disconnect
When disconnecting the ear th connection, be sure to disconnect
the power plug from the power outlet in advance.
(5)
Power plug
Check the shape of the power plug of the machine, and insert it into
a power outlet of the acceptable shape.
Power plug stated in power capacity.
D. Floor strength and level
This machine is considerably heavy and becomes heavier with an
option installed.
The floor must be strong enough to safely support the weight of the
The floor must be strong enough to safely support the weight of the
machine as well as any installed options.
If the unit is not horizontally installed, the toner density control is not
If the unit is not horizontally installed, the toner density control is not
performed normally, degrading the copy quality.
If not, color shift or image distortion may occur.
If not, color shift or image distortion may occur.
To assure proper Image quality, make sure the machine is setting
level.
E. Direct rays of the sun, dust, temperature,
humidity, gasses, chemicals, vibration
(1)
Temperature and humidity (Environmental
conditions)
conditions)
This machine is designed to per form properly under the specified
temperature and humidity. If the temperature and humidity exceeds
the specified range, the machine may not operate properly and or
cause equipment failure.
Especially when the humidity is too high, paper absorbs humidity to
Especially when the humidity is too high, paper absorbs humidity to
cause a paper jam or dirty copy.
Do not install the machine near a heater, a cooler, or a humidifier.
Do not install the machine near a heater, a cooler, or a humidifier.
Condensation may form inside the machine ca using multiple trou-
bles. Use enough care for ventilation.
No.
Content
1
Transportation space
2
Installing space
3
Power source (Capacity, fluctuation, safety)
4
Floor strength
5
Direct rays of the sun, dust, temperature, humidity, gases,
chemicals
11-13/16"
(30cm)
(30cm)
11-13/16"
(30cm)
(30cm)
17-23/32"
(45cm)
(45cm)
MX-7040N Transit, Installation (using) environment, Note - ii
Operational environment
Temperature: 10 to 35C
Humidity: 20 to 85% RH
Atmospheric pressure: 590 to 1013hPa (altitude: 0 to 2000 m)
Temperature: 10 to 35C
Humidity: 20 to 85% RH
Atmospheric pressure: 590 to 1013hPa (altitude: 0 to 2000 m)
(2)
Contaminates
If dust enters the machine, it may cause dirty copy and a p aper
jam, resulting in a shortened lifetime.
(3)
Direct sunlight
If the machine is installed under the rays of the sun, the exterior of
the machine may be discolored and abn ormal copies may be pro-
duced.
(4)
Gases and chemicals
Do not install the machine at a place where there are gases and
chemicals. Especially be careful to avoid installation near a diazo-
type copier, which produces ammonium gas.
Copy quality may be adversely affected and a t rouble may be
Copy quality may be adversely affected and a t rouble may be
caused.
* There was a trouble in a place where silicon-series gas or volatile
* There was a trouble in a place where silicon-series gas or volatile
components are generated. Use great care for avoiding this.
(5)
Vibration
Avoid installation near a machine which produces vibrations.
If vibrations are applied to the copier machine, copy images may be
If vibrations are applied to the copier machine, copy images may be
deflected and a trouble may be caused.
F. Note for handling PWB and electronic parts
When handling the PWB and the electronic p arts, be sur e to
observe the following precautions in order to prevent against dam-
age by static electricity.
• When in transit or storing, put the parts in an anti-static bag or an
• When in transit or storing, put the parts in an anti-static bag or an
anti-static case and do not touch them with bare hands.
• When and after removing the parts from an anti-static bag (case),
use an earth band as shown below:
• Put an earth band to your arm, and connect it to the machine.
• Put an earth band to your arm, and connect it to the machine.
85%
Humidity㧔RH㧕
60%
20%
MX-7040N Transit, Installation (using) environment, Note - iii
• When repairing or replacing an electronic part, perform the
procedure on an anti-static mat.
G. Note for proper drum, developing, fusing and
transfer unit handling
When handling the OPC drum, developing and transfer unit s,
observe the following items.
Drum unit
• To prevent damage to the OPC drum, avoid working on the drum
Drum unit
• To prevent damage to the OPC drum, avoid working on the drum
unit in high intensity light areas.
• When the OPC drum is removed from the machine, cover it with
light blocking material. (When using paper, use about 10 sheets
of paper to cover it.)
• Be careful not to attach fingerprints, oil, grease, or other foreign
material on the OPC drum surface.
Transfer unit
• Be careful not to "leave” fingerprints, oil, grease, or other foreign
• Be careful not to "leave” fingerprints, oil, grease, or other foreign
material on the transfer roller, primary transfer belt and second-
ary transfer belt.
Developing unit
• Be careful not to "leave” fingerprints, oil, grease, or other foreign
• Be careful not to "leave” fingerprints, oil, grease, or other foreign
material on the developing unit.
Fusing unit
• Be careful not to "leave” fingerprints, oil, grease, or other foreign
• Be careful not to "leave” fingerprints, oil, grease, or other foreign
material on the fusing roller and the external heating belt.
• Do not leave the fusing roller in contact state for a long time.
If these items are ne glected, a tr ouble may be generated in the
If these items are ne glected, a tr ouble may be generated in the
copy and print image quality.
2. Transit and delivery
A. Implements, facility, and manpower
It is recommendable to use a forklift for bringing in the machine for
safety.
If no forklift is available, man-power of two persons is required. The
If no forklift is available, man-power of two persons is required. The
machine is considerably heavy, and requires safety precautions for
delivery and installation.
Transit of the machine must be made in packed condition to the
Transit of the machine must be made in packed condition to the
installing place.
Since the hard disk drive is built in the machine, use car e not to
Since the hard disk drive is built in the machine, use car e not to
exert vibrations or shocks to the machine when in transit.
B. Delivery
Remove the packing materials prior to installation in the office envi-
ronment.
No.
Content
Method
1
Implements, facility,
and man power
Use a forklift. (If no forklift is available,
manpower of two persons is required.)
2
Delivery
Transit must be made in packed condition.
MX-7040N Transit, Installation (using) environment, Note - iv
3. Power configuration
A. Indoor wiring (power outlet) and breaker information
NOTE:
• Prepare an indoor wiring (power outlet) which is connected to the AC plug of the machine and its option units.
• Prepare an indoor wiring (power outlet) which is connected to the AC plug of the machine and its option units.
The required number of power outlets varies according to the combination of the option units.
Prepare the necessary number of them.
Example: (North America) Finisher "2.9A", large-capacity multi-stage tray "8A" 12A>10.9A=2.9A+8A Connectable to the same circuit
Example: (North America) Finisher "2.9A", large-capacity multi-stage tray "8A" 12A>10.9A=2.9A+8A Connectable to the same circuit
(breaker).
• For the AC cord of an option unit, use another indoor wiring (another breaker) than that for the machine.
For North America only
• The machine power is of 200V, an indoor wiring work may be required.
For Europe only
• Both of AC code 1 and 2 can be connected together into 16A AC outlet in case, but if the pow er source is less than 16A in case, notice the
For North America only
• The machine power is of 200V, an indoor wiring work may be required.
For Europe only
• Both of AC code 1 and 2 can be connected together into 16A AC outlet in case, but if the pow er source is less than 16A in case, notice the
following rules.
• Use different outlet which has separate breaker for each of the two AC cords of the machine.
• For additional installation of breakers and 200V indoor wiring, may be required certified jobs.
• For additional installation of breakers and 200V indoor wiring, may be required certified jobs.
4K finisher
(100-sheets
binding)
Multi-
folding
unit
Inserter
Decurler
unit
Machine 1
Machine 2
Paper pass
unit
Large-capacity
multi-stage tray
AC cord type
Inlet
Inlet
---
---
Direct
Direct
---
Inlet
North
America
62cpm
machine
70cpm
machine
Power supply
rating
120V/2.9A
AC power
is supplied
from the
finisher.
Power is
supplied
from the
machine.
Power is
supplied
from the
machine.
208-240V/12A
---
Power is
supplied from
the large-
capacity multi-
stage tray.
120V/8A
Power capacity
120V/15A
---
---
---
240V/20A
---
---
120V/15A
Form of the
plug
---
---
---
---
---
Form of the
power outlet
---
---
---
---
---
4K finisher
(100-sheets
binding)
Multi-
folding
unit
Inserter
Decurler
unit
Machine 1
Machine 2
Relay unit
Large-capacity
multi-stage tray
AC cord type
Inlet
---
---
---
Inlet
Inlet
---
Inlet
Europe/
UK
62cpm
machine
70cpm
machine
Power supply
rating
230V/1.5A
AC power
is supplied
from the
finisher.
Power is
supplied
from the
machine.
Power is
supplied
from the
machine.
230V/8A
230V/8A
Power is
supplied from
the large-
capacity multi-
stage tray.
230V/4A
Power capacity
230V/10A
---
---
---
230V/15A
230V/15A
---
230V/10A
Form of the
plug
---
---
---
---
Form of the
power outlet
---
---
---
---
Machine
Paper feed system
After-process system
AC power
supply
supply
4K
finisher
(100-sheets
binding)
finisher
(100-sheets
binding)
Multi-
folding
unit
folding
unit
Inserter
Decurler
unit
unit
Large-capacity
multi-stage tray
multi-stage tray
Paper
pass
unit
pass
unit
1