Sharp MX-FNX9 (serv.man22) Service Manual / Technical Bulletin ▷ View online
CCE-1098
Document Systems Division
1/2
SHARP CORPORATION
TECHNICAL BULLETIN
Date: December 27
th
2012
Model: MX-FNX1/9/17
Ref: CCE-1098
Ref: CCE-1098
Colour: White
Page: 1 OF 2
ENHANCEMENT FOR JAM DUE TO BUNCH ROLLER
PRESSURE LEVER BECOMING DETACHED
PRESSURE LEVER BECOMING DETACHED
1. Model Name:
MX-FNX1(Optional Inner Finisher for MX-1800N/2300 series/2700 series/3500 series/
4500
series)
MX-FNX9(Optional Inner Finisher for MX-4110N/4111N/4112N/5110N/5111N/5112N,
MX-2301N/2600 series/3100 series/MX-4100 series/5000 series,
MX-M283N/M363 series/M453 series/M503 series)
MX-FN17(Optional Inner Finisher for MX-2010U/2310U/3111U/2610N/3110N/3610N)
2. Symptom:
The pawl sections of LEVER-FE-PICK are hooked to HOLDER-FE-PICK-F/R but the
contact area of this can be insufficient, in some rare cases, the hooked section of
LEVER-FE-PICK detaches from HOLDER-FE-PICK-F/R,resulting in a misfeed inside the
inner
finisher.
3. Description:
Enhancement has been made by changing the positions of BUNCH ROLLER UP-DOWN
SHAFT, BUNCH ROLLER SHAFT2, and E-ring groove, pin or clip groove of
SHAFT-FE-PCIK-T and decreasing the gap between the HOLDER-FE-PICK-F/R and
LEVER-FE-PICK, this extends the contact area of the hooked pawls as mentioned above.
LEVER-FE-PICK
Hooked area
2/2
CCE-1098
- For MX-FNX1/FNX9
BUNCH ROLLER SHAFT 2 (0CW4141P20302)
BUNCH ROLLER UP/DOWN SHAFT (0CW4141P20402)
- For MX-FN17
SHAFT-FE-PICK-T
(0CW4188P20304)
SHAFT-FE-ARM
(0CW4188P20403)
4. Action:
From October 2012 production
5. Parts Action:
Ref.
No.
Model
name
Version P/G No.
Current parts
New parts
Price
rank
Q'ty Parts
name
Effective
time
Inter-
change-
ability
Parts code
Parts code
1
MX-FNX1
MX-FNX9
MX-FNX9
ALL
3-1
0CW4141P204B/ 0CW4141P20402
AW
1
BUNCH ROLLER
UP/DOWN SHAFT
UP/DOWN SHAFT
2012/10 3
3-25
0CW4141P203// 0CW4141P20302
BUNCH ROLLER
SHAFT 2
SHAFT 2
MX-FN17
3-20
0CW4188P203// 0CW4188P20304
AX
SHAFT-FE-PICK-T
3-30
0CW4188P204// 0CW4188P20403
AY
SHAFT-FE-ARM
<Interchange>
1. Interchangeable.
4. Not interchangeable.
2. Current type can be used in place of new type.
New type cannot be used in place of current type.
5. Interchangeable if replaced with same types of
related parts in use.
3. Current type cannot be used in place of new type.
New type can be used in place of current type.
6. Others.
Parts marked with "
" is important for maintaining the safety of the set. Be sure to replace these parts with
specified ones for maintaining the safety and performance of the set.
Move to the rear side 0.4mm
Move to the rear side 0.4mm
Move to the front side 0.2mm
Move to the rear side 0.4mm
Move to the rear side 0.3mm
Move to the front side 0.15mm
Move to the rear side 0.4mm
Display