Sharp MX-FNX5 Service Manual ▷ View online
MX-FNX5 REPLACEMENT AND ADJUSTMENT 3 – 3
3. JOGGER FENCE
1)
Open the front door.
2)
Pull out the jogger and stapler unit.
3)
Push both fences to the center.
4)
Remove the left jogger fence [A] ( x 1)
5)
Remove the right jogger fence [B] ( x 1).
NOTE:
If the screws are difficult to remove or re-attach, remove the
jogger fence belt and spring plate.
NOTE:
If the screws are difficult to remove or re-attach, remove the
jogger fence belt and spring plate.
4. SENSORS
A. PAPER HEIGHT SENSORS
Remove:
• Top cover. (
• Top cover. (
1. COVERS -D.)
• Left upper panel and left upper cover ( x 2,
x 2)
(
1. COVERS -C.)
[A] Protector plate ( x 1).
[B] Feeler ( x 1).
[C] Sensor bracket ( x 1).
[D] Paper height sensor - staple mode (
[B] Feeler ( x 1).
[C] Sensor bracket ( x 1).
[D] Paper height sensor - staple mode (
x 1, Pawls x4)
[E] Paper height sensor - standby mode (
x 1, Pawls x4)
[F] Paper height sensor - shift/Z-Fold(
x 1, Pawls x4).
B. EXIT GUIDE HP SENSOR
1)
Remove the top cover. (
1. COVERS -D.)
2)
Remove the left upper panel and left upper cover
( x 2,
( x 2,
x 2).
Remove:
[A] Sensor bracket [A] ( x 1).
[A] Sensor bracket [A] ( x 1).
[F]
[G]
[H]
[I]
[B]
[A]
[C]
[B]
[A]
[D]
[E]
[F]
[A]
MX-FNX5 REPLACEMENT AND ADJUSTMENT 3 – 4
[B] Exit guide HP sensor (
x 1, Pawls x3).
C. UPPER TRAY FULL AND EXIT SENSORS
(1) Upper Tray Full Sensor
1)
Remove the top cover.
2)
Remove the sensor cover [A] ( x 2).
3)
Remove the sensor bracket [B] ( x 1).
4)
Replace the upper tray full sensor [C] (
x1, x 1).
(2) Upper Tray Exit Sensor
1)
Remove the sensor bracket [D] ( x 1).
2)
Replace the upper tray exit sensor [E] (
x 1, x 1).
D. SHIFT TRAY EXIT SENSOR
• Remove the top cover (
1. COVERS -D.)
Remove:
[A] Sensor bracket ( x1)
[A] Sensor bracket ( x1)
[B] Shift tray exit sensor 1 ( x1,
x1)
[C] Shift tray exit sensor 2 ( x1,
x1)
[B]
[A]
[B]
[C]
[D]
[E]
[A]
[B]
[C]
MX-FNX5 REPLACEMENT AND ADJUSTMENT 3 – 5
E. ENTRANCE AND STAPLER TRAY ENTRANCE
SENSORS
(1) Entrance Sensor
1)
Disconnect the finisher from the copier.
2)
Remove the sensor bracket [A] ( x 1).
3)
Replace the entrance sensor [B] ( x 1) (
x 1).
(2) Stapler Tray Entrance Sensor
1)
Open the front door.
2)
Remove the sensor bracket [C] ( x 1).
3)
Replace the stapler tray entrance sensor [D] ( x 1)(
x 1).
F. MAIN BOARD, PRE-STACK PAPER SENSOR
1)
Remove the rear cover. (
1. COVERS -D.)
2)
Remove the main board bracket ( x6,
x8,
x All).
3)
Open the front door.
4)
Loosen the screw [A] ( x1)
Remove:
[B] Gear cover ( x1)
[C] Gear (
[B] Gear cover ( x1)
[C] Gear (
x1, Timing belt x1)
[D] Gear (
x1)
[E] Plate ( x2)
[F] Left vertical transport guide
[G] Middle vertical transport guide
[H] Pre-stack paper sensor (
[F] Left vertical transport guide
[G] Middle vertical transport guide
[H] Pre-stack paper sensor (
x1)
[B]
[A]
[D]
[C]
[A]
[B]
[C]
[D]
[E]
MX-FNX5 REPLACEMENT AND ADJUSTMENT 3 – 6
G. STAPLE TRIMMINGS HOPPER FULL SENSOR
• Open the front door
• Pull out the stapler unit
• Remove the rear cover ( x 2).
Remove:
[A] Staple trimmings hopper
[B] Hopper holder (
• Pull out the stapler unit
• Remove the rear cover ( x 2).
Remove:
[A] Staple trimmings hopper
[B] Hopper holder (
x1, Hook x1,
x1)
[C] Hopper full sensor (
x 1)
[D] Hopper set sensor (
x 1)
H. STAPLER ROTATION HP AND STAPLER
RETURN SENSORS
1)
Remove the stapler unit. (See next page.)
2)
Remove the stapler mount bracket [A] ( x 4) (Springs x 2).
3)
Replace the stapler rotation HP sensor [B] (
x 1).
4)
Replace the stapler return sensor [C] (
x 1).
[F]
[G]
[H]
[A]
[B]
[C]
[D]
[A]
[C]
[B]
Click on the first or last page to see other MX-FNX5 service manuals if exist.