Sharp MX-FN23 Service Manual ▷ View online
MX-FN23 DISASSEMBLY AND ASSEMBLY 8 – 5
3) Remove the E-ring, the tray paper entry collar, and the parallel
pin, and remove the rear edge take-up roller.
I. Alignment roller lift solenoid
1) Disconnect the connector, remove the screw, and remove the
roller lift solenoid.
NOTE: After fixing the roller lift solenoid, the plunger must be in
contact with the rear edge regulation plate in the free state.
Press the plunger with your finger to check to confirm that
the clearance between the take-up roller and the rear edge
regulation plate is 10 - 12mm.
Press the plunger with your finger to check to confirm that
the clearance between the take-up roller and the rear edge
regulation plate is 10 - 12mm.
J. Paper alignment motor F
1) Remove the JAM release knob, the one-way coupling, the
Mylar, the pulley, the SP pin, the E-ring, and the bearing, and
remove the paper entry roller.
remove the paper entry roller.
2)
Remove the screw, and remove the upper stay left.
3)
Remove the E-ring, and remove the pressure release drive
gear. Remove the E-ring, and slide the bearing, and remove
the paper delivery pressure release PG unit.
gear. Remove the E-ring, and slide the bearing, and remove
the paper delivery pressure release PG unit.
4)
Remove the E-ring, the Mylar, the pulley, and the parallel pin.
Remove the E-ring, and slide the bearing, and remove the
paper delivery roller unit.
Remove the E-ring, and slide the bearing, and remove the
paper delivery roller unit.
5)
Disconnect the connector. Remove the screw, and remove the
compiler.
compiler.
10 12mm
0mm
MX-FN23 DISASSEMBLY AND ASSEMBLY 8 – 6
6) Disconnect the connector. Remove the screw, and remove the
paper alignment motor F.
K. Paper alignment motor R
1) Disconnect the connector. Remove the screw, and remove the
paper alignment motor R.
L. Paper alignment plate home position sensor F
1) Remove the screw, remove the mounting plate, and discon-
nect the connector. Remove the paper alignment plate home
position F sensor from the mounting plate.
position F sensor from the mounting plate.
M. Paper alignment plate home position sensor R
1)
Remove the screw, remove the mounting plate, and discon-
nect the connector. Remove the paper alignment plate home
position R sensor from the mounting plate.
nect the connector. Remove the paper alignment plate home
position R sensor from the mounting plate.
N. Staple tray paper detector
1)
Remove the screw, and remove the sensor holder and the rear
edge regulation plate.
edge regulation plate.
2)
Remove the screw, and remove the jogger F and the jogger R.
3)
Remove the screw, and remove the alignment tray upper unit.
MX-FN23 DISASSEMBLY AND ASSEMBLY 8 – 7
4) Remove the staple tray paper detector, and disconnect the
connector.
3. Paper delivery
A. Delivery roller position sensor
1) Remove the rear cabinet.
2) Remove the E-ring, and remove the pressure release drive
2) Remove the E-ring, and remove the pressure release drive
gear. Disconnect the connector, and remove the paper deliv-
ery roller position sensor.
ery roller position sensor.
B. Tray lift motor
1) Remove the front cabinet.
2) Remove the harness holder.
3) Disconnect the connector, remove the screw, and remove the
2) Remove the harness holder.
3) Disconnect the connector, remove the screw, and remove the
lift drive frame.
4) Remove the worm gear and the screw, and remove the tray lift
motor.
C. Paddle solenoid
1)
Remove the E-ring, the paddler drive collar, the baring, the
gear, the parallel pin, the Mylar, the belt, and the pulley.
gear, the parallel pin, the Mylar, the belt, and the pulley.
2)
Remove the screw, and remove the EV frame unit.
3)
Remove the screw, and remove the paddle solenoid.
MX-FN23 DISASSEMBLY AND ASSEMBLY 8 – 8
NOTE: After fixing the paddle solenoid, the paddler solenoid arm
must be in contact with the paddler drive collar with the
plunger in the free state.
Press the plunger with your finger to check to confirm that
the clearance between the paddler solenoid arm and the
paddler drive collar is 0 - 1.5mm.
plunger in the free state.
Press the plunger with your finger to check to confirm that
the clearance between the paddler solenoid arm and the
paddler drive collar is 0 - 1.5mm.
D. Delivery tray position sensor, Delivery tray
lower limit sensor
1) Remove the delivery tray position sensor and the delivery tray
lower limit sensor.
E. Paper delivery motor
1) Remove the compiler.
2) Remove the spring, the E-ring, the gear, and remove the
2) Remove the spring, the E-ring, the gear, and remove the
screw.
3)
Disconnect the connector, remove the paper delivery motor
unit.
unit.
4)
Remove the screw, and remove the paper delivery motor.
F. Delivery roller lift motor
1)
Remove the screw, and remove the pressure release drive
cover. Remove the screw.
cover. Remove the screw.
2)
Disconnect the connector, and remove the delivery roller lift
motor.
motor.
0 - 1.5mm
0mm
Click on the first or last page to see other MX-FN23 service manuals if exist.