DOWNLOAD Sharp MX-FN19 / MX-FN20 / MX-PN12 (serv.man5) Service Manual ↓ Size: 2.44 MB | Pages: 9 in PDF or view online for FREE

MX-7040N  MX-FN19 (FINISHER (50 sheets binding))  13 – 1

 

MX-7040N

Service Manual

 

Since the illustrations of the former models are used, they may differ from the actual cases.

NOTE: For removal of the finisher, manpower of two persons or

more is required.

1)

Remove the fixing material, and remove the top case.

2)

Remove the bundled items from packing cushion.

3)

Holding the upper part of the saddle stitch finisher by two peo-
ple, pull up the saddle stitch finisher, and make it stand upright.
(Be careful to sliding worker's foot.)

4)

Remove the skid and packing cushions.

5)

One person tilt the finisher, another person remove the lower
tray.

6)

Remove the other side similarly.

MX-7040N  MX-FN19 (FINISHER (50 sheets binding))  13 – 2

1)

Remove the fixing tapes and protection material.

2)

Open the front upper door, and remove the fixing tapes and
protection material.

3)

Remove the screws and remove the fixing material for the
paper exit tray. (four positions)

1

Binding head round tapping M4 x 8

2

2

IT tapping M4 x 20

2

3

Binding head M4 x 12

4

4

Step screw

2

5

Rail

1

6

Rail reception sheet metal

1

7

Connection fixture F (for x3)

1

8

Connection fixture R (for x3)

1

9

Staple position label (For scanner)

1

10

Staple position label (For DSPF)

1

11

Punch position label (For scanner)

1

12

Punch position label (For DSPF)

1

13

Cushion (S)

1

14

Cushion (M)

1

15

Cushion (L)

1

1

2

3

6

4

5

7

8

9

11

12

10

13

15

14

X3

X3

MX-7040N  MX-FN19 (FINISHER (50 sheets binding))  13 – 3

NOTE: When the finisher is installed, first install the paper pass

unit, and then install the finisher.

NOTE: When the finisher and punch unit is installed at the same

time, first install the punch unit, and then install the finisher.

1)

Install the rail (Packed items No.5) to the finisher with the fixing
screws (Packed items No.1).

2)

Install the rail reception sheet metal (Packed items No.6) to the
main unit with the fixing screws (Packed items No.2).

1)

Install the connection fixture R (Packed items No.8) to the
main unit with the fixing screws (Packed items No.3).

2)

Install the connection fixture F (Packed items No.7) to the main
unit with the fixing screws (Packed items No.3).

1)

Attach the cushion (S) (Packed items No.13), the cushion (M)
(Packed items No.14) and the cushion (L) (Packed items
No.15) to the position indicated in the figure.

Cushion A
attachment
position

Cushion B
attachment
position

Cushion C
attachment
position

Cushion A attachment
reference (Front edge of
the relay path left
cabinet)

Cushion A attachment
reference (Upper side of
the groove in the relay
path left cabinet)

Cushion B attachment
reference (Upper edge
of the machine left
cabinet)

Cushion B attachment
reference (Rear edge of
the handle hole)

Cushion C attachment
reference (Front edge of
the upper cushion)

Cushion C attachment
reference (Upper edge of the
machine left lower cabinet)

MX-7040N  MX-FN19 (FINISHER (50 sheets binding))  13 – 4

1)

Insert the rail of the finisher into the slit on the rail reception
sheet metal of the main unit, install the finisher.

2)

Remove the screw, and remove the connector cover on rear
side of the finisher.

3)

Check that the center of the screw hole of the finisher is in the
range of specification of an oval hole of the connection fixture
that exist on main body rear side.

* When not the range of specification, progress to the proce-

dure of "E. Adjustment".
If the adjustment is not required, remove the screws from
the screw hole directly and push the caster into it until the
installation fixing.

1)

Remove the finisher from the main unit.

2)

Remove the screw, slide to the left the front lower cover, and
remove it.