Sharp MX-FN11 (serv.man2) Service Manual ▷ View online
MX-FN11 DISASSEMBLY AND ASSEMBLY 5 – 20
3) Remove the two screws [6], and open the harness holder [7] at
three positions, and disconnect the connectors [8] at two posi-
tions.
tions.
4) Insert your finger into the hole in the back of the No. 1 tray [9].
Push the tray lift motor gear [10] toward you to release the
clutch, and lift the No. 1 tray [9].
clutch, and lift the No. 1 tray [9].
CAUTION: When the clutch of the tray lift motor gear is released, it
falls by its own weight. When releasing the clutch, there-
fore, hold the tray at the bottom in advance. When
installing it, take care not to twist the tray cable.
fore, hold the tray at the bottom in advance. When
installing it, take care not to twist the tray cable.
e. Removal of No. 2 tray
CAUTION: Note for installing or moving the tray
When moving down the tray, push up the shutter [1],
and release the latch [2] on the lower surface of the tray
to lower the tray.
When the latch is released, the tray will free-fall. Hold
the tray with your hand during the removal.
and release the latch [2] on the lower surface of the tray
to lower the tray.
When the latch is released, the tray will free-fall. Hold
the tray with your hand during the removal.
1)
Remove the screw [1], and remove the stopper [2].
2)
Remove the two screws [3], and disconnect the connector [4].
3)
Insert your finger into the hole in the back of the No.2 tray [5].
Push the tray lift motor gear [6] toward you to release the
clutch, and lift the No.2 tray [5].
Push the tray lift motor gear [6] toward you to release the
clutch, and lift the No.2 tray [5].
CAUTION: When the clutch of the tray lift motor gear is released, it
falls by its own weight. When releasing the clutch, there-
fore, hold the tray at the bottom in advance. When
installing it, take care not to twist the tray cable.
fore, hold the tray at the bottom in advance. When
installing it, take care not to twist the tray cable.
[7]
[8]
[6]
[6]
[9]
[10]
[2]
[1]
[2]
[1]
[4]
[3]
[3]
[5]
[6]
MX-FN11 DISASSEMBLY AND ASSEMBLY 5 – 21
(4) Buffer roller
a. Removal of front cover
1) Remove a screw [1] to remove the foot cover [2].
1) Remove a screw [1] to remove the foot cover [2].
2) Remove the three screws [3], and slide the front cover [4] to
the left and remove it.
b. Removal of rear cover
1)
1)
Remove the three screws [1], and lift and remove the rear
cover [2].
cover [2].
c. Removal of left upper cover
1)
1)
Remove the two screws [1].
2)
With the upper door [2] open, tilt the left upper cover [3] to the
right, and remove it.
right, and remove it.
CAUTION: When installing, be sure to engage the two pawls [4] of
the left upper cover with the metal plates.
[1]
[2]
[4]
[3]
[1]
[2]
[3]
[2]
[1]
[4]
MX-FN11 DISASSEMBLY AND ASSEMBLY 5 – 22
d. Removal of upper door
1) Open the upper door [1], and release the hook [2] at two posi-
1) Open the upper door [1], and release the hook [2] at two posi-
tions.
2) Remove the screw [3], and remove the upper door [1].
e. Removal of buffer roller
1) Remove the buffer roller shaft [2] from the arm [1] at two posi-
1) Remove the buffer roller shaft [2] from the arm [1] at two posi-
tions.
2) Remove the clips [3] at two positions, and remove the two
buffer rollers [4].
(5) Return roller
a. Removal of front cover
1) Remove a screw [1] to remove the foot cover [2].
1) Remove a screw [1] to remove the foot cover [2].
2)
Remove the three screws [3], and slide the front cover [4] to
the left and remove it.
the left and remove it.
b. Removal of rear cover
1)
1)
Remove the three screws [1], and lift and remove the rear
cover [2].
cover [2].
[3]
[1]
[2]
[3]
[3]
[1]
[1]
[2]
[4]
[1]
[2]
[4]
[3]
[1]
[2]
MX-FN11 DISASSEMBLY AND ASSEMBLY 5 – 23
c. Removal of left upper cover
1) Remove the two screws [1].
2) With the upper door [2] open, tilt the left upper cover [3] to the
1) Remove the two screws [1].
2) With the upper door [2] open, tilt the left upper cover [3] to the
right, and remove it.
CAUTION: When installing, be sure to engage the two pawls [4] of
the left upper cover with the metal plates.
d. Removal of grate-shaped upper guide
1) Move down the tray [1] lower than the grate-shaped upper
1) Move down the tray [1] lower than the grate-shaped upper
guide [2]. (For moving of the tray, refer to "Removal of No. 1
tray.")
tray.")
2) Remove the five screws [3], and remove the grate-shaped
upper guide [2].
e. Removal of No.1 tray
CAUTION: Note for installing or moving the tray
When moving down the tray, push up the shutter [1],
and release the latch [2] on the lower surface of the tray
to lower the tray.
When the latch is released, the tray will free-fall. Hold
the tray with your hand during the removal.
and release the latch [2] on the lower surface of the tray
to lower the tray.
When the latch is released, the tray will free-fall. Hold
the tray with your hand during the removal.
1)
Remove the screw [1], and remove the metal plate [2] and the
slide guide [3]. If the grate-shaped upper guide has been
removed, this procedure is unnecessary.
slide guide [3]. If the grate-shaped upper guide has been
removed, this procedure is unnecessary.
2)
Remove the screw [4], and remove the stopper [5].
[3]
[2]
[1]
[4]
[3]
[2]
[1]
[2]
[1]
[1]
[3]
[2]
[5]
[4]
Click on the first or last page to see other MX-FN11 (serv.man2) service manuals if exist.