DOWNLOAD Sharp MX-CF11 / MX-6240N / MX-7040N (serv.man3) Service Manual ↓ Size: 582.62 KB | Pages: 5 in PDF or view online for FREE

MX-7040N  MX-CF11 (INSERTER)  17 – 3

1)

Install the paper guide C (bundled with the decurler unit No.13)
to the paper feed side of the inserter with the screws (bundled
with the decurler unit No.1). 

1)

Remove the decurler unit plates.

2)

Attach the protection sheet (bundled with the decurler unit
No.14) to the decurler unit with the screw (bundled with the
decurler unit No.1).

MEMO: Temporarily attach the protection sheet to the decurler
unit with the duplex tape (back of the protection sheet), then fix
it with the screw.

3)

Attach the connection plate F/R (Packed items No.8, 9) to the
decurler unit with the screws (Packed items No.18 Screw
4x6L).

1)

Open the inserter front upper cover, remove the screw, and
pull the lock lever toward you.

2)

Connect the inserter to the decurler unit. 
Insert the pin in the decurler unit side into the unit hole.

3)

Push up the lock lever to lock the unit and the decurler unit.
Use the removed screw to fix the lock lever.

MEMO: If they cannot be locked, follow the installing proce-
dures (height adjustment) of the complex machine and options
to adjust the height.

1)

Loosen the screw of the fall-prevention stay, and store the
stay.

Fall-prevention stay

1

MX-7040N  MX-CF11 (INSERTER)  17 – 4

For installation of the tray unit, use manpower of two or more per-
sons.

1)

Remove the rear cover of the tray unit.

2)

Hold the grip of the unit to install it to the inserter.

NOTE: When the tray unit is inserted, the machine becomes

unstable. In order to prevent against falling, therefore,
connect the after-process mechanism (the finisher,
etc.) the fall-prevention to the left side of the inserter
and put the tray unit on it.

3)

Attach the screw (Packed items No. 16) .

4)

Connect five connectors.

5)

Remove the front inner cover. (2 screws)

6)

Fix the tray unit. (2 screws (Packed items No. 16))

7)

Attach the base cover. (1 screw (Packed items No. 3))

8)

Attach the front door to the front inner cover, and attach the L-
hinge pins (Packed items No. 12).

MEMO: Insert the L-hinge pin in the lower section into the back
of the Black Mylar.

Rear cover

Plate grip (Used for installation)

Plate grip

Grip

Screw (M4 x 12)

Connect five connectors.

Front inner cover

Tray unit

Screw (M4 x 12)

Base cover

1

MX-7040N  MX-CF11 (INSERTER)  17 – 5

9)

Attach the front inner cover to the tray unit. (2 screws)

10) Attach the accessory cover (Packed items No. 1) with the

screw (Packed items No. 17) and the winding bushing (Packed
items No. 21).

1)

Connect the connector to the decurler unit.

MEMO: When the adjuster bolt is turned counterclockwise, the
height is decreased. When turned clockwise, the height is
increased.

MEMO: The specification of the height and the tilt adjustment are
as follows.

Height: The difference of level between top surface of the adjacent
device is within 

2mm.

Tilt: The difference of clearance between upper and lower part of
the adjacent device is within 

2mm.

1)

Place an adjustment dish under every adjuster bolt, and screw
the bolt. (4 positions)

2)

Turn the adjuster bolts (1) and (2) in the above figure, and
adjust the height.

3)

Turn the adjuster bolts (3) and (4) in the above figure, and
adjust the tilt.

MX-7040N  MX-CF11 (INSERTER)  17 – 5

9)

Attach the front inner cover to the tray unit. (2 screws)

10) Attach the accessory cover (Packed items No. 1) with the

screw (Packed items No. 17) and the winding bushing (Packed
items No. 21).

1)

Connect the connector to the decurler unit.

MEMO: When the adjuster bolt is turned counterclockwise, the
height is decreased. When turned clockwise, the height is
increased.

MEMO: The specification of the height and the tilt adjustment are
as follows.

Height: The difference of level between top surface of the adjacent
device is within 

2mm.

Tilt: The difference of clearance between upper and lower part of
the adjacent device is within 

2mm.

1)

Place an adjustment dish under every adjuster bolt, and screw
the bolt. (4 positions)

2)

Turn the adjuster bolts (1) and (2) in the above figure, and
adjust the height.

3)

Turn the adjuster bolts (3) and (4) in the above figure, and
adjust the tilt.