Sharp MX-CF11 / MX-6240N / MX-7040N (serv.man2) Service Manual ▷ View online
MX-7040N MX-FN19 (FINISHER (50 sheets binding)) 13 – 3
2. Installation
NOTE: When the finisher is installed, first install the paper pass
unit, and then install the finisher.
NOTE: When the finisher and punch unit is installed at the same
time, first install the punch unit, and then install the finisher.
A. Installation of the rail
1)
Install the rail (Packed items No.5) to the finisher with the fixing
screws (Packed items No.1).
screws (Packed items No.1).
2)
Install the rail reception sheet metal (Packed items No.6) to the
main unit with the fixing screws (Packed items No.2).
main unit with the fixing screws (Packed items No.2).
B. Installation of the connection fixture F/R
1)
Install the connection fixture R (Packed items No.8) to the
main unit with the fixing screws (Packed items No.3).
main unit with the fixing screws (Packed items No.3).
2)
Install the connection fixture F (Packed items No.7) to the main
unit with the fixing screws (Packed items No.3).
unit with the fixing screws (Packed items No.3).
C. Attaching the cushion
1)
Attach the cushion (S) (Packed items No.13), the cushion (M)
(Packed items No.14) and the cushion (L) (Packed items
No.15) to the position indicated in the figure.
(Packed items No.14) and the cushion (L) (Packed items
No.15) to the position indicated in the figure.
Cushion A
attachment
position
attachment
position
Cushion B
attachment
position
attachment
position
Cushion C
attachment
position
attachment
position
Cushion A attachment
reference (Front edge of
the relay path left
cabinet)
reference (Front edge of
the relay path left
cabinet)
Cushion A attachment
reference (Upper side of
the groove in the relay
path left cabinet)
reference (Upper side of
the groove in the relay
path left cabinet)
Cushion B attachment
reference (Upper edge
of the machine left
cabinet)
reference (Upper edge
of the machine left
cabinet)
Cushion B attachment
reference (Rear edge of
the handle hole)
reference (Rear edge of
the handle hole)
Cushion C attachment
reference (Front edge of
the upper cushion)
reference (Front edge of
the upper cushion)
Cushion C attachment
reference (Upper edge of the
machine left lower cabinet)
reference (Upper edge of the
machine left lower cabinet)
MX-7040N MX-FN19 (FINISHER (50 sheets binding)) 13 – 4
D. Check of the connected position of main unit
and finisher
1)
Insert the rail of the finisher into the slit on the rail reception
sheet metal of the main unit, install the finisher.
sheet metal of the main unit, install the finisher.
2)
Remove the screw, and remove the connector cover on rear
side of the finisher.
side of the finisher.
3)
Check that the center of the screw hole of the finisher is in the
range of specification of an oval hole of the connection fixture
that exist on main body rear side.
range of specification of an oval hole of the connection fixture
that exist on main body rear side.
* When not the range of specification, progress to the proce-
dure of "E. Adjustment".
If the adjustment is not required, remove the screws from
the screw hole directly and push the caster into it until the
installation fixing.
If the adjustment is not required, remove the screws from
the screw hole directly and push the caster into it until the
installation fixing.
E. Adjustment
1)
Remove the finisher from the main unit.
2)
Remove the screw, slide to the left the front lower cover, and
remove it.
remove it.
MX-7040N MX-FN19 (FINISHER (50 sheets binding)) 13 – 5
3)
Open the front upper cover.
4)
Remove the front upper cover.
5)
Remove the screws, and open the front lower cover.
6)
Remove the fixing tapes.
7)
Remove the screws, and remove the auxiliary wheels.
8)
Remove the screws, and remeve the rear lower cover.
9)
Remove the fixing tapes.
2
1
1
MX-7040N MX-FN19 (FINISHER (50 sheets binding)) 13 – 6
10) Loosen both of the caster fixing screws of the front side and
rear side.
11) Remove the screw, and remove the spanner installed inside
the front lower door.
12) Turn the bolt for which the adjustment is necessary, and adjust
to become it within the range of specification.
13) Check to insure that the upper and lower clearances between
the main unit and the finisher are even.
Click on the first or last page to see other MX-CF11 / MX-6240N / MX-7040N (serv.man2) service manuals if exist.