Sharp MX-C310 / MX-C311 / MX-C312 / MX-C380 / MX-C381 / MX-C400 / MX-C401 (serv.man11) Service Manual ▷ View online
MX-C401 MX-C310/MX-C311/MX-C312/MX-C380/MX-C381/MX-C400/MX-C401 (MAIN UNIT) 1 – 3
4)
Remove the carton.
5)
Remove the parts included in the package.
6)
Remove the main unit from the bottom padding, and remove
the polyethylene bag.
the polyethylene bag.
B. Removal of the fixing tape and protection
material
C. Check the packed items
1)
Check that all the parts are in the package.
4. Installation
A. Installation of the developer cartridges
1)
Open the front cover.
2)
Turn the lock lever until it stops to release the lock, and
remove the waste toner box.
remove the waste toner box.
No.
Packed part names
Quantity
1
Developer cartridge
1 piece for each color
2
Toner cartridge
1 piece for each color
(Other than North America)
3
Waste toner box
1 (Except for MX-C312)
4
AC cord
200V series only: 1 piece
5
Operation Manual
1 set
6
Operation Manual pocket
Yes
1
2
3
5
4
6
MX-C401 MX-C310/MX-C311/MX-C312/MX-C380/MX-C381/MX-C400/MX-C401 (MAIN UNIT) 1 – 4
3)
Turn the lock lever to the horizontal position to release the
lock, and open the drum positioning plate unit.
lock, and open the drum positioning plate unit.
4)
Shake the developer cartridge 5 - 6 times horizontally, and
remove the protection material from the developer cartridge.
remove the protection material from the developer cartridge.
Insert the developer cartridge straight and horizontally until it
locks.
locks.
NOTE: When handling the developer cartridge, do not touch the
magnet roller section and the shutter section.
5)
While pressing the developer cartridge, pull out the heat seal
straight.
straight.
NOTE: If the heat seal is pulled out with a strong force or diago-
nally, it may be broken off. Be sure to pull it slowly and
straight.
straight.
After puling out the heat seal completely, check to confirm
that there is a red mark at the edge of the heat seal.
that there is a red mark at the edge of the heat seal.
If there is no red mark, it means that the heat seal has been
broken. In such a case, the developer cartridge must be
replaced with a new one.
broken. In such a case, the developer cartridge must be
replaced with a new one.
6)
Close the lock cover of the developer cartridge.
7)
Close the drum positioning plate unit, and put the lock lever
upright to lock.
upright to lock.
MX-C401 MX-C310/MX-C311/MX-C312/MX-C380/MX-C381/MX-C400/MX-C401 (MAIN UNIT) 1 – 5
B. Installation of toner cartridges
* The life of each toner cartridge is as follows:
Black toner cartridge: equivalent to approximately 2.5K (A4/LT
5%)
5%)
Color toner cartridge: equivalent to approximately 2.5K (A4/LT
5%)
5%)
1)
Shake the toner cartridge (included in package) horizontally
several times.
several times.
2)
Remove the heat seal.
3)
Insert the toner cartridge horizontally and straight until it locks.
NOTE: Be sure to install the color cartridges to their proper posi-
tions. Avoid installation to a different color position.
NOTE: Do not forcibly insert the toner cartridge. Keep holding the
cartridge and completely insert it.
NOTE: When the machine is transported with the developing unit
removed, be sure to remove the toner cartridge. (if not
toner may become clogged.)
toner may become clogged.)
NOTE: Do not remove or insert the toner cartridge with the devel-
oper cartridge removed.
C. Cleaning of LSU's dust-proof glass
* Dust from the transfer belt or shutter or some other adjacent part
may fall onto the LSU during transport or installation. Be sure to
clean the dust-proof glass before checking the image quality.
clean the dust-proof glass before checking the image quality.
1)
Remove the LSU cleaning rod from the front cover.
2)
Face the cleaner downward, and slowly insert the LSU clean-
ing rod into the LSU cleaning hole.
ing rod into the LSU cleaning hole.
* The LSU cleaning hole is indicated with a label.
3)
After inserting the LSU cleaning rod to the bottom, pull it out
until the lead edge of the cleaning unit is separated from the
LSU clearing surface. Repeat 2 - 3 times for cleaning.
until the lead edge of the cleaning unit is separated from the
LSU clearing surface. Repeat 2 - 3 times for cleaning.
4)
There are four LSU cleaning holes. Clean all the holes simi-
larly.
larly.
5)
Return the LSU cleaning rod to the front cover.
CYAN
YELLOW
MAGENTA
BLACK
[Color toner cartridge positions]
MX-C401 MX-C310/MX-C311/MX-C312/MX-C380/MX-C381/MX-C400/MX-C401 (MAIN UNIT) 1 – 6
6)
Install the waste toner box, and turn the lock lever to the left
until it stops to lock the waste toner box.
until it stops to lock the waste toner box.
7)
Close the front cover.
D. Installation of the operation manual pocket
1)
Install the Operation Manual pocket (included in package)
cover to the left side of the machine.
cover to the left side of the machine.
a)
First, insert the pawl on the lower side of the Operation
Manual pocket.
Manual pocket.
b)
Then, lift the pawl on the upper side and insert it, and slide
down to install.
down to install.
E. Tray size setup
1)
Gently pull out the tray until it stops. If paper remains in the
tray, remove it.
tray, remove it.
2)
Adjust the guide plates A and B to the vertical size and the hor-
izontal size of paper.
izontal size of paper.
The guide plates A and B are movable. Hold the fixing knob to
slide the guide plates A and B to match the paper size.
slide the guide plates A and B to match the paper size.
3)
Insert the tray slowly.
The machine automatically detects the set paper size.
F. Specifications setting
Use SIM26 to set to the specifications according to the customer's
request.
request.
To customize one of the following items after destination setting,
change the set value of the item.
change the set value of the item.
G. Image quality check and adjustment
Check the following items regarding to image qualities. For adjust-
ment and checking procedures, refer to [4] ADJUSTMENTS in the
separate Service Manual.
ment and checking procedures, refer to [4] ADJUSTMENTS in the
separate Service Manual.
(1)
Image skew check and adjustment
1)
Select ALL in the SIM50-22 mode to execute the automatic
image registration adjustment.
image registration adjustment.
2)
The current skew level is displayed on the SKEW display
menu.
menu.
3)
Write down the displayed skew level.
SIM No
Content
26
6
Destination setting
SIM No
Content
26
3
Auditor specifications, mode setting
18
Toner save mode enable/disable setting (Japan and UK
versions only)
* For the other destinations, this setting is made by the user
versions only)
* For the other destinations, this setting is made by the user
program.
52
Count-up enable/disable setting of non-print paper passing for
each counter
each counter
53
User color calibration enable/disable setting
65
Staple limit quantity setting
Click on the first or last page to see other MX-C310 / MX-C311 / MX-C312 / MX-C380 / MX-C381 / MX-C400 / MX-C401 (serv.man11) service manuals if exist.