DOWNLOAD Sharp MX-C310 / MX-C311 / MX-C312 / MX-C380 / MX-C381 / MX-C400 / MX-C401 (serv.man11) Service Manual ↓ Size: 24.38 MB | Pages: 68 in PDF or view online for FREE

Model
MX-C310 MX-C311 MX-C312 MX-C380 MX-C381 MX-C400 MX-C401 (serv.man11)
Pages
68
Size
24.38 MB
Type
PDF
Document
Service Manual
Brand
Device
Copying Equipment / Installation Manual
File
mx-c310-mx-c311-mx-c312-mx-c380-mx-c381-mx-c400-mx.pdf
Date

Sharp MX-C310 / MX-C311 / MX-C312 / MX-C380 / MX-C381 / MX-C400 / MX-C401 (serv.man11) Service Manual ▷ View online

MX-C401  MX-C310/MX-C311/MX-C312/MX-C380/MX-C381/MX-C400/MX-C401 (MAIN UNIT)  1 – 2
(2)
Dust
If dust enters the machine, it may cause dirty copy and a paper
jam, resulting in a shortened lifetime.
(3)
Direct rays of the sun
If the machine is installed under the rays of the sun, the exterior of
the machine may be discolored and abnormal copies may be pro-
duced.
(4)
Gases and chemicals
Do not install the machine at a place where there are gases and
chemicals. Especially be careful to avoid installation near a diazo-
type copier, which produces ammonium gas.
Copy quality may be adversely affected and a trouble may be
caused.
(5)
Vibration
Avoid installation near a machine which produces vibrations.
If vibrations are applied to the copier machine, copy images may be
deflected and a trouble may be caused.
2. Transit and delivery
A. Implements, facility, and manpower
It is recommendable to use a forklift for bringing in the machine for
safety.
If no forklift is available, man-power of two persons is required. The
machine is considerably heavy, and requires safety precautions for
delivery and installation.
Transit of the machine must be made in packed condition to the
installing place.
Since the hard disk drive is built in the machine, use care not to
exert vibrations or shocks to the machine when in transit.
B. Delivery
Remove the packing materials prior to installation in the office envi-
ronment.
3. Unpacking
A. Unpacking procedure
1)
Remove the PP band.
2)
Remove the top case.
3)
Remove the parts included in the package.
No.
Content
Method
1
Implements, facility, 
and man power
Use a forklift. (If no forklift is available, 
manpower of two persons is required.) 
2
Delivery
Transit must be made in packed condition.
MX-C401  MX-C310/MX-C311/MX-C312/MX-C380/MX-C381/MX-C400/MX-C401 (MAIN UNIT)  1 – 3
4)
Remove the carton.
5)
Remove the parts included in the package.
6)
Remove the main unit from the bottom padding, and remove
the polyethylene bag.
B. Removal of the fixing tape and protection 
material
C. Check the packed items
1)
Check that all the parts are in the package.
4. Installation
A. Installation of the developer cartridges
1)
Open the front cover.
2)
Turn the lock lever until it stops to release the lock, and
remove the waste toner box.
No.
Packed part names
Quantity
1
Developer cartridge
1 piece for each color
2
Toner cartridge
1 piece for each color
(Other than North America)
3
Waste toner box
1 (Except for MX-C312)
4
AC cord
200V series only: 1 piece
5
Operation Manual
1 set
6
Operation Manual pocket
Yes
1
2
3
5
4
6
MX-C401  MX-C310/MX-C311/MX-C312/MX-C380/MX-C381/MX-C400/MX-C401 (MAIN UNIT)  1 – 4
3)
Turn the lock lever to the horizontal position to release the
lock, and open the drum positioning plate unit.
4)
Shake the developer cartridge 5 - 6 times horizontally, and
remove the protection material from the developer cartridge.
Insert the developer cartridge straight and horizontally until it
locks.
NOTE: When handling the developer cartridge, do not touch the
magnet roller section and the shutter section.
5)
While pressing the developer cartridge, pull out the heat seal
straight.
NOTE: If the heat seal is pulled out with a strong force or diago-
nally, it may be broken off. Be sure to pull it slowly and
straight.
After puling out the heat seal completely, check to confirm
that there is a red mark at the edge of the heat seal.
If there is no red mark, it means that the heat seal has been
broken. In such a case, the developer cartridge must be
replaced with a new one.
6)
Close the lock cover of the developer cartridge.
7)
Close the drum positioning plate unit, and put the lock lever
upright to lock.
MX-C401  MX-C310/MX-C311/MX-C312/MX-C380/MX-C381/MX-C400/MX-C401 (MAIN UNIT)  1 – 5
B. Installation of toner cartridges
* The life of each toner cartridge is as follows:
Black toner cartridge: equivalent to approximately 2.5K (A4/LT
5%)
Color toner cartridge: equivalent to approximately 2.5K (A4/LT
5%)
1)
Shake the toner cartridge (included in package) horizontally
several times.
2)
Remove the heat seal.
3)
Insert the toner cartridge horizontally and straight until it locks.
NOTE: Be sure to install the color cartridges to their proper posi-
tions. Avoid installation to a different color position.
NOTE: Do not forcibly insert the toner cartridge. Keep holding the
cartridge and completely insert it.
NOTE: When the machine is transported with the developing unit
removed, be sure to remove the toner cartridge. (if not
toner may become clogged.)
NOTE: Do not remove or insert the toner cartridge with the devel-
oper cartridge removed.
C. Cleaning of LSU's dust-proof glass
* Dust from the transfer belt or shutter or some other adjacent part
may fall onto the LSU during transport or installation. Be sure to
clean the dust-proof glass before checking the image quality.
1)
Remove the LSU cleaning rod from the front cover.
2)
Face the cleaner downward, and slowly insert the LSU clean-
ing rod into the LSU cleaning hole.
* The LSU cleaning hole is indicated with a label.
3)
After inserting the LSU cleaning rod to the bottom, pull it out
until the lead edge of the cleaning unit is separated from the
LSU clearing surface. Repeat 2 - 3 times for cleaning.
4)
There are four LSU cleaning holes. Clean all the holes simi-
larly.
5)
Return the LSU cleaning rod to the front cover.
CYAN
YELLOW
MAGENTA
BLACK
[Color toner cartridge positions]
Page of 68
Display

Click on the first or last page to see other MX-C310 / MX-C311 / MX-C312 / MX-C380 / MX-C381 / MX-C400 / MX-C401 (serv.man11) service manuals if exist.