Sharp MX-C310 / MX-C311 / MX-C312 / MX-C380 / MX-C381 / MX-C400 / MX-C401 (serv.man11) Service Manual ▷ View online
MX-C401 MX-CSX1/CSX2 (500 SHEET PAPER FEED UNIT) 2 – 3
* When the main unit is put on the MX-CSX1, it is automati-
cally locked at the left and the right of the rear side.
2)
Pull out the tray of the main unit and that of the MX-CSX1.
3)
Loosen the hand screws on the left and the right sides.
4)
Hang the fixing clasp on the main unit, and tighten the hand
screws.
screws.
5)
Push in and close the trays.
D. Turn on the power of the main unit
1)
Power to the main unit.
2)
Turn ON the power switch.
3)
Turn ON the power switch on the operation panel.
MX-C401 MX-CSX1/CSX2 (500 SHEET PAPER FEED UNIT) 2 – 4
3. Adjustments
A. Image off-center automatic adjustment
(Document table mode)
1)
Enter the SIM50-28 mode.
(4.3 Inch LCD model)
(8.5/7.0 Inch LCD model)
2)
Select [SETUP/PRINT ADJ].
3)
Select [ALL].
(4.3 Inch LCD model)
(8.5/7.0 Inch LCD model)
NOTE: When [ALL] is selected, the adjustments of the follow-
ing two items are performed at a same time.
* [LEAD]: Print image lead edge image position adjustment
* [OFFSET]: Print image off-center adjustment
4)
Select the paper feed trays to be adjusted. (Select all the
trays.)
trays.)
Set A4 (11" x 8.5") paper in each paper feed tray in advance.
(4.3 Inch LCD model)
(8.5/7.0 Inch LCD model)
5)
Press [EXECUTE] key.
The adjustment pattern is printed out. (Paper is fed from the
selected paper feed tray, and the adjustment pattern of each
paper feed tray is printed out.)
selected paper feed tray, and the adjustment pattern of each
paper feed tray is printed out.)
6)
Set the adjustment pattern in the center reference on the docu-
ment table.
ment table.
NOTE: Fit the adjustment pattern correctly with the document
guide.
7)
Press [EXECUTE] key.
(4.3 Inch LCD model)
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
$872,0$*(326,7,21$'-8670(176(59,&(
7(67
2&ǂ$'-
63)ǂ$'-
5(68/7
%.0$*ǂ$'-
6(78335,17ǂ$'-
'$7$
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
$872,0$*(326,7,21$'-8670(176(59,&(
7(67
/($'
$//
2))6(7
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
$872,0$*(326,7,21$'-8670(176(59,&(
7(67
0)7
&6
&6
/&&
&6
&6
$'8
(;(&87(
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
$872,0$*(326,7,21$'-8670(176(59,&(
3/($6(:$,7
12:(;(&87,1*
7(67
(;(&87(
5(35,17
MX-C401 MX-CSX1/CSX2 (500 SHEET PAPER FEED UNIT) 2 – 5
(8.5/7.0 Inch LCD model)
The following item is automatically adjustment.
* Print image lead edge image position adjustment
* Print image off-center adjustment
Perform the procedures of 6) - 7) for the printed adjustment
pattern of each paper feed tray.
pattern of each paper feed tray.
8)
Press [OK] key. (For the 4.3 Inch LCD model, press the OSA
shortcut key.)
shortcut key.)
The adjustment result becomes valid.
(4.3 Inch LCD model)
(8.5/7.0 Inch LCD model)
NOTE: When an error occurs in the automatic adjustment of
SIM50-28, place white paper on the adjustment pattern
and perform the adjustment.
and perform the adjustment.
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
$872,0$*(326,7,21$'-8670(176(59,&(
35/'0)7
&$6&$6
$'8
&$6&$6
/&&
35260)7
&$6
&$6
$'8
&$6
&$6
/&&
7(67
'$7$
5(35,17
5(6&$1
5(75<
MX-C401 MX-FN12 (FINISHER) 3 – 1
MX-C401
Service Manual
[3] MX-FN12 (FINISHER)
1. Unpacking
A. Removal of the finisher
B. Removal of the fixing tape and protection
material
1)
Remove the finisher from the polyethylene bag, and remove
the fixing tape and the protection materials.
the fixing tape and the protection materials.
C. Check the packed items
2. Installation
<Precautions for installation>
Before execution of installation, check to confirm that the communi-
cation lamp on the operation panel and the data lamp under it are
not lighted or blinking.
cation lamp on the operation panel and the data lamp under it are
not lighted or blinking.
A. Turn off the power of the main unit
1)
Turn OFF the power switch on the operation panel.
2)
Check to confirm that the operation panel is turned OFF, and
then turn OFF the power switch.
then turn OFF the power switch.
3)
Disconnect the power plug from the power outlet.
No.
Packed part names
Quantity
1
Machine connection unit
1
2
Paper exit tray
1
3
Staple position label (For RSPF)
1
4
Staple position label (For OC)
1
2
1
4
3
Click on the first or last page to see other MX-C310 / MX-C311 / MX-C312 / MX-C380 / MX-C381 / MX-C400 / MX-C401 (serv.man11) service manuals if exist.