Sharp MX-C300P / MX-C300PE / MX-C300PL (serv.man3) Service Manual ▷ View online
MX-C300P MX-CS11 (500 SHEET PAPER FEED UNIT) 3 – 1
MX-C300P
Service Manual
[3] MX-CS11 (500 SHEET PAPER FEED UNIT)
1. Installation
<Precautions for installation>
Before execution of installation, check to confirm that the data lamp
under it are not lighted or blinking.
under it are not lighted or blinking.
A. Turn off the power of the main unit
1)
Check to confirm that the operation panel is turned OFF, and
then turn OFF the power switch.
then turn OFF the power switch.
2)
Disconnect the power plug from the power outlet.
B. Install the main unit to the MX-CS11.
NOTE: If the main unit is combined with the MX-CS11, it must
be used as a desktop machine and must not be used on
the floor in order to prevent against falling.
the floor in order to prevent against falling.
1)
Put the main unit on the MX-CS11 so that they fit together.
NOTE: When holding the main unit, use two persons.
NOTE: When lifting / holding the main engine, never lift. Lift
the engine at the right and left cover bottoms using the hand
grab indentions provided.
the engine at the right and left cover bottoms using the hand
grab indentions provided.
2)
Pull out the trays of the main unit and MX-CS11.
3)
Attach the main unit and MX-CS11 with the plates (Packed
item Plate A) and the screws (Packed items M4x10 P Tight
and M4x8 S Tight).
item Plate A) and the screws (Packed items M4x10 P Tight
and M4x8 S Tight).
4)
Remove the Rear cover. .
5)
Attach the main unit and MX-CS11 with the plates (Packed
item Plate B) and the screws (Packed items M4x10 P Tight).
item Plate B) and the screws (Packed items M4x10 P Tight).
C. Turn on the power of the main unit
1)
Power to the main unit.
2)
Turn ON the power switch.
2. Adjustments
A. Image off-center automatic adjustment
(Document table mode)
1)
Enter the SIM50-10 mode.
2)
Set A4 (11" x 8.5") paper in each paper feed tray.
3)
Press [OK] key.
The adjustment pattern is printed out. (Paper is fed from the
paper feed tray.)
paper feed tray.)
Perform the procedures of 2) - 3) for the printed adjustment
pattern of each paper feed tray.
pattern of each paper feed tray.
4)
Press [OK] key.
The adjustment result becomes valid.
A
D
A
C
B
D
D
B
D
D
6LP3$3(52))6(7
㸸
%.0$*
㸸0$,10)7
㸸
>@
㸸
>@
(;(&
0$,1&6
6LP3$3(52))6(7
㸸
%.0$*
㸸0$,10)7
㸸
>@
㸸
>@
(;(&
0$,1&6
MX-C300P Setting, Adjustments, Operation check 4 – 1
MX-C300P
Service Manual
[4] Setting, Adjustments, Operation check
1. Firmware version check and version
up
After installation of all the options to the machine, use SIM49-1 to
check the version of each firmware. If it is not the latest version,
upgrade it to the latest one.
2. Function and operation check
Check that the following operations are normal.
Check item list
Equipped condition
Key-in (operation panel)
Display (operation panel)
Paper feed
Display (operation panel)
Paper feed
operation
Hand feed
Main unit paper
Main unit paper
tray
Desk unit paper
Desk unit paper
feed tray
With the desk unit installed
Paper size detection
Originals size
Originals size
detection
Original table
mode
Paper exit operation
MX-C300P Setup and adjustment data recording 5 – 1
MX-C300P
Service Manual
[5] Setup and adjustment data recording
Print the various setup data and the adjustment data (list) with
SIM22-6 and keep the data.
- In case of a memory trouble, if the data is not kept, all the adjust-
- In case of a memory trouble, if the data is not kept, all the adjust-
ments must be made again.
-
If the data is kept, the setup values and the adjustment values
can be entered without adjustments, shortening the servicing
time.
MX-C300P Necessary steps before moving the machine 6 – 1
MX-C300P
Service Manual
[6] Necessary steps before moving the machine
1) If the following options are installed, remove all of them from
the machine.
- Paper pass unit
- Paper pass unit
2) Remove the following consumable parts from the machine.
- Paper
- Toner cartridges
- Toner cartridges
3) Lock the following sections.
- Paper cassette lift plate
- Not to leak the developer, fix the caps for four colors firmly to
- Not to leak the developer, fix the caps for four colors firmly to
the developing unit.
Click on the first or last page to see other MX-C300P / MX-C300PE / MX-C300PL (serv.man3) service manuals if exist.