DOWNLOAD Sharp MX-C300P / MX-C300PE / MX-C300PL (serv.man3) Service Manual ↓ Size: 1.62 MB | Pages: 16 in PDF or view online for FREE

Model
MX-C300P MX-C300PE MX-C300PL (serv.man3)
Pages
16
Size
1.62 MB
Type
PDF
Document
Service Manual
Brand
Device
Copying Equipment / Installation Manual
File
mx-c300p-mx-c300pe-mx-c300pl-sm3.pdf
Date

Sharp MX-C300P / MX-C300PE / MX-C300PL (serv.man3) Service Manual ▷ View online

  MX-C300P/MX-C300PE/C300PL (MAIN UNIT)  2 – 2
2.Installation
A.Remove the cap of developing unit
1) Remove the tray. 
2) Open the front cover.  
3) Remove the silica gel material.   
4) Remove fixing tapes and the caps on the developing units. 
NOTE: Be  sure  to  keep  the  caps.  Caps  are  used  when  the
machine is transferred to the different location.
B.Installation of toner cartridges
* The life of each toner cartridge is as follows:
Black  toner  cartridge:  equivalent  to  approximately  1K  (A4/LT
5%)
Color  toner  cartridge:  equivalent  to  approximately  1K  (A4/LT
5%)
1) Shake the toner cartridge (included in package) vertically sev-
eral times.
2) Insert the toner cartridge horizontally and straight until it locks.
NOTE: Be sure to install the color cartridges to their proper posi-
tions. Avoid installation to a different color position.
NOTE: Do not forcibly insert the toner cartridge. Keep holding the
cartridge and completely insert it.
NOTE: When the machine is transported with the developing unit
removed,  be  sure  to  remove  the  toner  cartridge.  (if  not
toner may become clogged.)
NOTE: Do not remove or insert the toner cartridge with the devel-
oper cartridge removed.
NOTE: Press  the  center  of  the  cartridge  until  it  is  locked  when
installing the cartridge.  
Yellow
Magenta Cyan
Black
  MX-C300P/MX-C300PE/C300PL (MAIN UNIT)  2 – 3
C. Fusing unit lever
1) Open the right door unit.. 
2) Turn the levers of the Fusing unit to add the pressure. 
* Only the levers can add or release the pressure. There is no
screw for adding or releasing the pressure.
NOTE: When the machine is left for one month without using, the
Fusing heat roller could be deformed. If the machine is not
going to be used for an extended period, release the pres-
sure on the fusing rollers. 
D.Tray size setup
1) Gently  pull  out  the  tray  until  it  stops.  If  paper  is  in  the  tray,
remove it.
2) Adjust the guide plates A and B to the vertical size and the hori-
zontal size of paper. 
The guide plates A and B are movable. Hold the fixing knob to
slide the guide plates A and B to match the paper size.
3) Insert the tray slowly.
4) Turn  ON  the  machine  and  press  the  [SPECIAL  FUNCTION]
key on the LCD, and press the [UP] or [DOWN] key to select
"Paper Size Set".
E.Specifications setting
Use SIM26 to set to the specifications according to the customer's
request.
To  customize  one  of  the  following  items  after  destination  setting,
change the set value of the item.
F.Paper fixing
The Paper fixing is not bundled with the machine. When the follow-
ing cases occur, it is recommended to use the Paper fixing. 
The parts code of Paper fixing : LFIX-0627FCZ1
a. Even if the Output tray extension is used, the fed paper falls off
from the output tray.  
 The customer does not like to use the Output tray extension. 
(1)
(2)
(2)
(2)
0LATE
0LATE
SIM No
Content
26
6
Destination setting
SIM No
Content
26 18 Toner save mode enable/disable setting
* For the other destinations, this setting is made by 
the user program.
53 Auto color calibration enable/disable setting
Paper fixing
  MX-C300P/MX-C300PE/C300PL (MAIN UNIT)  2 – 4
3.Image quality check
A. Execution items
Execute  the  checking  items  about  the  printing  quality.  Regarding
the specific procedures for the printing quality, refer to the Service
Manual [5] ADJUSTMENT.  
B. Description
(1) Print engine image distortion confirmation and
adjustment 
This adjustment performs the print engine image distortion adjust-
ment, the OPC drum phase adjustment, and the color registration
adjustment simultaneously.
1) Enter SIM50-22 mode and perform the auto registration adjust-
ment.
2) When the adjustment is completed, [EXECUTE] key returns to
the normal display, and the value of the adjustment result is dis-
played.
The current skew level for each color is displayed on the SKEW
display section.
3) Make  test  print  in  the  simulation  mode  for  checking  whether
the void, off-center and printing quality are proper. 
If the test results are not proper, refer to [5] ADJUSTMENT of
the Service Manual and perform the adjustments.   
- Void, Off-center ; SIM50-20
When the  result of  the void and the  off-center  are  not  good,
perform [ADJ5] by referring the [5] ADJUSTMENT of the Ser-
vice Manual. 
- Printing quality ; SIM64-5 (SIM67-23 can also be used as the
check)
When the result of the print quality is not good, perform [ADJ6]
by referring the [5] ADJUSTMENT of the Service Manual. 
6LP$8725(*,67$'-
3UHVV2..H\           (;(&
6LP$8725(*,67$'-
               
(;(&
6LP$8725(*,67$'-    
5(*,67B68%B&
5(*,67B68%B&',)
5(*,67B0$,1B&B)
5(*,67B0$,1B&B)',)



6LP$8725(*,67$'-    
6.(:B.
6.(:B&
6.(:B&',)
6.(:B0
6LP$8725(*,67$'-    
5(*,67B0$,1B<B5',)
3+$6(
3+$6(EHIRUH





MX-C300P  MX-CS11 (500 SHEET PAPER FEED UNIT)  3 – 1
MX-C300P
Service Manual
 
[3] MX-CS11 (500 SHEET PAPER FEED UNIT)
1. Installation
<Precautions for installation>
Before execution of installation, check to confirm that the data lamp
under it are not lighted or blinking.
A. Turn off the power of the main unit
1)
Check to confirm that the operation panel is turned OFF, and
then turn OFF the power switch.
2)
Disconnect the power plug from the power outlet.
B. Install the main unit to the MX-CS11.
NOTE: If the main unit is combined with the MX-CS11, it must 
be used as a desktop machine and must not be used on 
the floor in order to prevent against falling.
1)
Put the main unit on the MX-CS11 so that they fit together.
NOTE: When holding the main unit, use two persons.
NOTE: When lifting / holding the main engine, never lift. Lift
the engine at the right and left cover bottoms using the hand
grab indentions provided.
2)
Pull out the trays of the main unit and MX-CS11.  
3)
Attach the main unit and MX-CS11 with the plates (Packed
item Plate A) and the screws (Packed items M4x10 P Tight
and M4x8 S Tight). 
4)
Remove the Rear cover. . 
5)
Attach the main unit and MX-CS11 with the plates (Packed
item Plate B) and the screws (Packed items M4x10 P Tight). 
C. Turn on the power of the main unit
1)
Power to the main unit.
2)
Turn ON the power switch.
2. Adjustments
A. Image off-center automatic adjustment 
(Document table mode)
1)
Enter the SIM50-10 mode.
2)
Set A4 (11" x 8.5") paper in each paper feed tray.
3)
Press [OK] key.
The adjustment pattern is printed out. (Paper is fed from the
paper feed tray.)
Perform the procedures of 2) - 3) for the printed adjustment
pattern of each paper feed tray.
4)
Press [OK] key. 
The adjustment result becomes valid.
A
D
A
C
B
D
B
D
6LP3$3(52))6(7
 %.0$*
                 
㸸0$,10)7

>@         
 

(;(&
0$,1&6
6LP3$3(52))6(7
 %.0$*
                 
㸸0$,10)7

>@         
 

(;(&
0$,1&6
Page of 16
Display

Click on the first or last page to see other MX-C300P / MX-C300PE / MX-C300PL (serv.man3) service manuals if exist.