DOWNLOAD Sharp MX-C250 / MX-C250E / MX-C250F / MX-C250FE / MX-C250FR / MX-C300F / MX-C300W / MX-C300WE / MX-C300A / MX-C300WR (serv.man40) Service Manual ↓ Size: 903.41 KB | Pages: 4 in PDF or view online for FREE

Model
MX-C250 MX-C250E MX-C250F MX-C250FE MX-C250FR MX-C300F MX-C300W MX-C300WE MX-C300A MX-C300WR (serv.man40)
Pages
4 Few pages! See other manuals at the bottom of the first or last page.
Size
903.41 KB
Type
PDF
Document
Service Manual / Technical Bulletin
Brand
Device
Copying Equipment / MFPC PWB replacement procedure
File
mx-c250-mx-c250e-mx-c250f-mx-c250fe-mx-c250fr-mx-c.pdf
Date

Sharp MX-C250 / MX-C250E / MX-C250F / MX-C250FE / MX-C250FR / MX-C300F / MX-C300W / MX-C300WE / MX-C300A / MX-C300WR (serv.man40) Service Manual / Technical Bulletin ▷ View online

(MFPC PWB replacement procedure)
 
(1) Remove the exteriors.
 Remove the rear cabinet fixing screws (x 3).
        
* Open the right door, and remove (a) right
  
cabinet upper in manner of the illustration below.
 
    *Remove the right cabinet while sliding it upward.
 Unlock the lock pawl while slightly lifting up the left
 
  side of the rear cabinet and remove it.
  
 
(2) Replace MFPC PWB
 Wear the earth band. Remove MFPC shield plate, and then remove all connectors on MFPC PWB.(29points
 Connector of FFC harness has the lock pawl.  Unlock the lock pawl, and then remove the harness.
 
 
 
 
Note1) For the precautions and procedure on the PWB replacement, please see Service Manual.
 
 
 
 
Note2) When handling MFPC PWB, hold the end face of PWB to prevent PWB from electrostatically charge.
 
 
 
 
Note3) Pay attention to the thermal pads attached to the back side of MFPC PWB.
M3*8S
M3*6S
M3*6S
M3*6
M3*6S
Slightly lift up the 
scanner and remove 
the pawl of the right 
cabinet upper.
Wear the earth 
 
(3) Replace EEP-ROM of the MFPC PWB (NEW PBW) which will be replaced with
         the original PWB (defective one).
  
  
  
  
Note) when mounting EEPROM, be careful about the deformation of the leads
 on ROM, mistake of the inserting direction, or incomplete insertion etc.
 
(4) Handling of the harness
   
Note) Check all Connector again if there is no incomplete insertion, no missing insertion,
 or no insertion in a slanting direction.
Special care
Connector of the star mark is even
 if incompletely inserted, 
the machine will work.
Please special attention.
         
  Note) Be careful about incorrect wiring which trigger the factors of the harnesses being under tension 
          or the pinched wire due to the incorrect wiring of the harness. 
*Be careful about the inserting direction.
 
(5) Mount MFPC shield plate
*Place the harnesses, not the wire being 
stuck with the PWB shield plate.
【 MFPC   Upper side 】
【 MFPC Lower side 】
① Insert FFC while the lock lever is set to the upper side.
② Pull down the lock lever, and then lock the connector.
M3*8S
【○】
【×】
Be careful about the position of the earth 
Hook the 
shield plate.
 
(6) Mount the exterior
Open the right door, and mount the right
 Mount the rear cabinet and fix it with
 cabinet and the right cabinet upper.
the screw.
(Setting procedure)
(1) Sim26-6 (Destination setting)
(2) Time adjustment
  【Setting input procedure】
   Function→System Setting→Admin password"00000"→Initial setting→Date and time→yyyy,mm,dd
   
Time setting
 → 
OK (Cursor key)
(3) Sim50-12
The document off-center adjustment setting
(4) Sim50-22(Auto resist Adjustment
(5) Sim46-24 (copy color balance auto adjustment)
(6) Sim66-2 (Clearing of Soft SW relating to the FAX)
(7) Sim66-10 (Clearing of the image memory)
(8) Sim6-90 (Factory settings)
Insert the pawl into 
the notch.
Display

Sharp MX-C250 / MX-C250E / MX-C250F / MX-C250FE / MX-C250FR / MX-C300F / MX-C300W / MX-C300WE / MX-C300A / MX-C300WR (serv.man40) Service Manual / Technical Bulletin ▷ Download

  • DOWNLOAD Sharp MX-C250 / MX-C250E / MX-C250F / MX-C250FE / MX-C250FR / MX-C300F / MX-C300W / MX-C300WE / MX-C300A / MX-C300WR (serv.man40) Service Manual ↓ Size: 903.41 KB | Pages: 4 in PDF or view online for FREE
  • Here you can View online or download the Service Manual / Technical Bulletin for the Sharp MX-C250 / MX-C250E / MX-C250F / MX-C250FE / MX-C250FR / MX-C300F / MX-C300W / MX-C300WE / MX-C300A / MX-C300WR (serv.man40) in PDF for free, which will help you to disassemble, recover, fix and repair Sharp MX-C250 / MX-C250E / MX-C250F / MX-C250FE / MX-C250FR / MX-C300F / MX-C300W / MX-C300WE / MX-C300A / MX-C300WR (serv.man40) Copying Equipment. Information contained in Sharp MX-C250 / MX-C250E / MX-C250F / MX-C250FE / MX-C250FR / MX-C300F / MX-C300W / MX-C300WE / MX-C300A / MX-C300WR (serv.man40) Service Manual / Technical Bulletin (repair manual) includes:
  • Disassembly, troubleshooting, maintenance, adjustment, installation and setup instructions.
  • Schematics, Circuit, Wiring and Block diagrams.
  • Printed wiring boards (PWB) and printed circuit boards (PCB).
  • Exploded View and Parts List.