Sharp MX-C250 / MX-C250E / MX-C250F / MX-C250FE / MX-C250FR / MX-C300F / MX-C300W / MX-C300WE / MX-C300A / MX-C300WR (serv.man12) User Manual / Operation Manual ▷ View online
MODEL: MX-C250
MX-C250F
MX-C300F
MX-C300W
DIGITAL FULL COLOUR MULTIFUNCTIONAL SYSTEM
START GUIDE
This guide explains important point to note for installation and usage. The Operation Guide for
the machine is on the accompanying CD-ROM. View the Operation Guide when you use the
machine after the initial setup is completed.
Keep this manual close at hand for reference whenever needed.
English ........ 3
Ce guide fournit des instructions importantes concernant l'installation et l'utilisation de cet
appareil. Le Mode d'emploi de la machine se trouve sur le CD-ROM. Consultez le Mode
d'emploi lorsque vous utilisez la machine après la configuration initiale.
Conservez ce guide à portée de main afin de vous y reporter ultérieurement en cas de besoin.
Français ...... 7
Esta guía presenta observaciones importantes de instalación y uso. El Manual de instrucciones
de la máquina está incluido en el CD-ROM suministrado. Consulte el Manual de instrucciones
para utilizar la máquina una vez finalizada la configuración inicial.
Mantenga este manual a mano para consultarlo cuando lo necesite.
Español ..... 11
Este guia explica pontos importantes que devem ser considerados ao instalar e utilizar o equipamento. O
Guia de Operação para a máquina encontra-se no CD-ROM fornecido. Consulte o Guia de Operação
quando você utilizar a máquina após a configuração inicial estar concluída.
Mantenha este manual ao seu alcance para que o mesmo possa ser consultado sempre que necessário.
Português
(Brasil) ...... 15
............ 22
START GUIDE
GUIDE DE DEMARRAGE
GUÍA DE INICIO
GUIA DE INÍCIO
3
English
CAUTIONS
To ensure safe use of the machine, this manual uses various safety symbols.
The safety symbols are classified as explained below. Be sure you understand
the meaning of the symbols when reading the manual.
the meaning of the symbols when reading the manual.
WARNING
Indicates a risk of death or serious injury.
CAUTION
Indicates a risk of human injury or property damage.
When removing the power plug from the outlet, do not pull on the cord.
Pulling on the cord may cause damage such as wire exposure and
breakage, and may result in fire or electrical shock.
If you will not use the machine for a long time, be sure to
If you will not use the machine for a long time, be sure to
remove the power plug from the outlet for safety.
When moving the machine, switch off the main power and
When moving the machine, switch off the main power and
remove the power plug from the outlet before moving.
The cord may be damaged, creating a risk of fire or electrical shock.
Power notes
WARNING
Be sure to connect the power cord only to a power outlet that meets
the specified voltage and current requirements. Also make certain the
outlet is properly grounded. Do not use an extension cord or adapter
to connect other devices to the power outlet used by the machine.
Using an improper power supply may cause fire or electrical shock.
* For the power supply requirements, see the name plate in the lower
left corner of the left side of the machine.
Do not damage or modify the power cord.
Placing heavy objects on the power cord, pulling it, or forcibly
bending it will damage the cord, resulting in fire or electrical shock.
Do not insert or remove the power plug with wet hands.
This may cause electrical shock.
Meaning of the symbols
CAUTION!
HOT
HOT
PINCH POINT
KEEP CLEAR
KEEP CLEAR
PROHIBITED
ACTIONS
ACTIONS
DO NOT
DISASSEMBLE
DISASSEMBLE
MANDATORY
ACTIONS
ACTIONS
CAUTION
Symbols in this manual
Do not install the machine on an unstable or slanted surface. Install the
machine on a surface that can withstand the weight of the machine.
Risk of injury due to the machine falling or toppling.
If peripheral devices are to be installed, do not install on an uneven floor, slanted
surface, or otherwise unstable surface. Danger of slippage, falling, and toppling. Install
the product on a flat, stable surface that can withstand the weight of the product.
Do not install in a location with moisture or dust.
Do not install in a location with moisture or dust.
Risk of fire and electrical shock.
If dust enters the machine, dirty output and machine failure may result.
Locations that are excessively hot, cold, humid, or dry (near
Locations that are excessively hot, cold, humid, or dry (near
heaters, humidifiers, air conditioners, etc.)
The paper will become damp and condensation may form inside the
machine, causing misfeeds and dirty output.
If the location has an ultrasonic humidifier, use pure water for humidifiers in the
humidifier. If tap water is used, minerals and other impurities will be emitted,
causing impurities to collect on the inside of the machine and create dirty output.
Locations exposed to direct sunlight
Locations exposed to direct sunlight
Plastic parts may become deformed and dirty output may result.
Locations with ammonia gas
Installing the machine next to a diazo copy machine may cause dirty output.
Do not install the machine in a location with poor air circulation.
A small amount of ozone is created inside the machine during printing.
The amount of ozone created is not sufficient to be harmful; however, an
unpleasant odor may be noticed during large copy runs, and thus the machine
should be installed in a room with a ventilation fan or windows that provide
sufficient air circulation. (The odor may occasionally cause headaches.)
* Install the machine so that people are not directly exposed to exhaust from the machine.
If installed near a window, ensure that the machine is not exposed to direct sunlight.
Near a wall
Be sure to allow the required space
around the machine for servicing
and proper ventilation. (The machine
should be no closer than the
distances indicated below from walls.
The indicated distances are for the
case when a saddle finisher and large
capacity paper tray are not installed.)
30 cm
30 cm
45 cm
Locations subject to vibration.
Vibration may cause failure.
Installation notes
CAUTION
CAUTION
• The machine should be installed near an accessible power outlet for
easy connection.
• Connect the machine to a power outlet which is not used for other electric
appliances. If a lighting fixture is connected to the same outlet, the light may flicker.
Do not throw a toner cartridge into a fire.
Toner may fly and cause burns.
Store a toner cartridge out of the reach of children.
About consumables
CAUTION
Do not place a container of water or other liquid, or a metal
object that might fall inside, on the machine.
If the liquid spills or the object falls into the machine, fire or electrical shock may result.
Do not remove the machine casing.
Do not remove the machine casing.
High-voltage parts inside the machine may cause electrical shock.
Do not make any modifications to this machine.
Doing so may result in personal injury or damage to the machine.
Do not use a flammable spray to clean the machine.
If gas from the spray comes in contact with hot electrical components
or the fusing unit inside the machine, fire or electrical shock may result.
If you notice smoke, a strange odor, or other abnormality, do
If you notice smoke, a strange odor, or other abnormality, do
not use the machine.
If used in this condition, fire or electrical shock may result.
Immediately switch off the main power and remove the power plug from the power outlet.
Contact your dealer or nearest authorised service representative.
If a thunder storm begins, switch off the main power and remove the power
If a thunder storm begins, switch off the main power and remove the power
plug from the outlet to prevent electrical shock and fire due to lightning.
If a piece of metal or water enters the machine, switch off the
main power and remove the power plug from the power outlet.
Contact your dealer or nearest authorised service representative. Using
the machine in this condition may result in electrical shock or fire.
Handling precautions
WARNING
CAUTION
Do not look directly at the light source.
Doing so may damage your eyes.
Do not block the ventilation ports on the machine. Do not install
the machine in a location that will block the ventilation ports.
Blocking the ventilation ports will cause heat to build up in the
machine, creating a risk of fire.
The fusing unit and paper exit area are hot. When removing a misfeed, do
The fusing unit and paper exit area are hot. When removing a misfeed, do
not touch the fusing unit and paper exit area. Take care not to burn yourself.
When loading paper, removing a misfeed, performing
maintenance, closing the front and side covers, and inserting
and removing trays, take care that your fingers are not pinched.
Wave length
790 nm ± 10 nm
Pulse times
(9.97 µs ± 0.034 ns) / 7 mm
Output power Max 0.6 mW
Caution
Use of controls or adjustments or performance of procedures other than those
specified herein may result in hazardous radiation exposure.
This Digital Equipment is CLASS 1 LASER PRODUCT (IEC 60825-1 Edition 2-2007).
Laser information
4
Caution!
For complete electrical disconnection, pull out the main plug.
The socket-outlet shall be installed near the equipment and shall be
easily accessible.
Shielded interface cables must be used with this equipment to
maintain compliance with EMC regulations.
The equipment should be installed near an accessible socket outlet
for easy disconnection.
Each instruction also covers the optional units used with these products.
For the users of the fax function
(for MX-C250F/C300F/C300W)
FAX interface cable and Line cable:
These special accessories must be used with the device.
The declaration of conformity may be consulted at:
http://www.sharp.de/doc/MX-C300W_MX-C300WE.pdf
http://www.sharp.de/doc/MX-C250F_MX-C250FE.pdf
Important safety instructions
• If any of your telephone equipment is not operating properly, you
should immediately remove it from your telephone line, as it may
cause harm to the telephone network.
• Never install telephone wiring during a lightning storm.
• Never install telephone socket in wet locations unless the socket is
specifically designed for wet locations.
• Never touch uninsulated telephone wires or terminals unless the
telephone line has been disconnected at the network interface.
• Use caution when installing or modifying telephone lines.
• Avoid using a telephone (other than a cordless type) during an
electrical storm. There may be a remote risk of electric shock from
lightning.
• Do not use a telephone to report a gas leak in the vicinity of the
leak.
• Do not install or use the machine near water, or when you are wet.
Take care not to spill any liquids on the machine.
• Save these instructions.
Important Notice for New Zealand Users
General
"The grant of a Telepermit for any item of terminal equipment
indicates only that Telecom has accepted that the item complies
with minimum conditions for connection to its network. It indicates no
endorsement of the product by Telecom, nor does it provide any sort
of warranty. Above all, it provides no assurance that any item will work
correctly in all respects with another item of Telepermitted equipment
of a different make or model, nor does it imply that any product is
compatible with all of Telecom’s network services."
This equipment is not capable, under all operating conditions, of
This equipment is not capable, under all operating conditions, of
correct operation at the higher speeds for which it is designed.
Telecom will accept no responsibility should difficulties arise in these
circumstances. This condition typically applies to 56 kbit/s modems.
This equipment shall not be set up to make automatic calls to
This equipment shall not be set up to make automatic calls to
Telecom’s 111 Emergency Service.
This equipment should not be used under any circumstances that
This equipment should not be used under any circumstances that
may constitute a nuisance to other Telecom customers.
This equipment may not provide for the effective hand-over of a call
This equipment may not provide for the effective hand-over of a call
to another device connected to the same line.
In order to operate within the limits for compliance with Telecom’s
In order to operate within the limits for compliance with Telecom’s
specifications, the associated equipment shall be set to ensure that automatic
calls to different numbers are spaced such that there is not less than 5
seconds between the end of one call attempt and the beginning of another.
Notice for Users in Australia and New Zealand
Your fax machine and the telephone system
WARNING NOTICE:
NO calls can be made to or from this fax during a mains power failure.
WARNING
WARNING
Australian Communications and Media Authority (ACMA) regulations
state that no unauthorised changes or modifications to this equipment
are permitted.
Complies with the following standards,
AS/NZS 60950.1
AS/ACIF S002, NZ TELECOM and AS/NZS CISPR 22
These limits are designed to provide reasonable protection against
interference in an installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause interference. However, there
is no guarantee that interference will not occur in a particular installation.
SOFTWARE LICENCE
The SOFTWARE LICENCE will appear when you install the software
from the CD-ROM. By using all or any portion of the software on the
CD-ROM or in the machine, you are agreeing to be bound by the
terms of the SOFTWARE LICENCE.
• The explanations in this manual assume that you have a working
knowledge of your Windows or Macintosh computer.
• For information on your operating system, please refer to your
operating system manual or the online Help function.
• The explanations of screens and procedures in this manual are
primarily for Windows 7 in Windows
®
environments. The screens
may vary depending on the version of the operating system.
• This manual contains references to the fax function. However, please
note that the fax function is not available in some countries and regions.
• This manual contains explanations of the PC-Fax driver and PPD
driver. However, please note that the PC-Fax driver and PPD driver
are not available and do not appear on the software for installation in
some countries and regions.
In this case, please install the English version if you want to use
these drivers.
• Considerable care has been taken in preparing this manual. If
you have any comments or concerns about the manual, please
contact your dealer or nearest authorised service representative.
• This product has undergone strict quality control and inspection
procedures. In the unlikely event that a defect or other problem
is discovered, please contact your dealer or nearest authorised
service representative.
• Aside from instances provided for by law, SHARP is not responsible for
failures occurring during the use of the product or its options, or failures
due to incorrect operation of the product and its options, or other
failures, or for any damage that occurs due to use of the product.
Products that have earned the ENERGY STAR
®
are designed to protect the environment
through superior energy efficiency.
through superior energy efficiency.
The products that meet the ENERGY STAR
®
guidelines carry the
ENERGY STAR
®
logo.
The products without the logo may not meet the ENERGY STAR
®
guidelines.
This product is designed for commercial application only and
as such it falls outside the scope of Regulation (EC) 1275/2008
implementing EU Directive 2005/32/EC on eco-design requirements
for standby and off mode electric power consumption. Sharp does
not recommend the product for domestic application and will not
accept any liability for such use.
as such it falls outside the scope of Regulation (EC) 1275/2008
implementing EU Directive 2005/32/EC on eco-design requirements
for standby and off mode electric power consumption. Sharp does
not recommend the product for domestic application and will not
accept any liability for such use.
Warranty
While every effort has been made to make this document as accurate
and helpful as possible, SHARP Corporation makes no warranty of
any kind with regard to its content. All information included herein is
subject to change without notice. SHARP is not responsible for any
loss or damages, direct or indirect, arising from or related to the use
of this operation manual.
© Copyright SHARP Corporation 2013. All rights reserved.
Reproduction, adaptation or translation without prior written
permission is prohibited, except as allowed under copyright laws.
If this equipment does cause interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a different circuit to that
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
The Ringer Equivalence Number (REN) for this equipment is written
on the label.
Important safety information
In Australia, installing or modifying telephone lines should only be
done by an ACMA licenced serviceman. In New Zealand, installing
or modifying telephone lines should be done in accordance with
Telecom wiring practices.
Wireless LAN (for MX-C300W)
The communication range of wireless LAN may shorten or
communication may not be possible in some usage environments,
due to shielding materials, the installation location, the effects of
ambient radio noise, data transmission speed, and other factors.
Display