Sharp MX-B201D (serv.man6) Service Manual ▷ View online
MX-FX12 FAX SOFT SWITCH 2 - 7
S
W
20
5
Receivable
memory capacity
memory capacity
Used to set the remained memory capacity for allowing call-in.
128Kbyte
0
The machine doesn’t arrive when it decreases more than this
capacity.
capacity.
1: 64Kbyte
0: 128Kbyte
6
Inhibited to use
0
7
0
8
0
S
W
21
1
Interval between
completion of
communication
and the next call
completion of
communication
and the next call
Used to set the interval between completion of communication and
the next call.
the next call.
1sec.
0
2
0
3
Setting is made in binary input.
0
4
Binary input
0
5
Bit No.
1
2
3
4
5
6
7
8
0
6
Set range
0 to 255sec.
0
7
0
8
1
S
W
22
1
Inhibited to use
0
2
0
3
0
4
0
5
0
6
0
7
0
8
0
S
W
23
1
Inhibited to use
0
2
0
3
0
4
0
5
0
6
0
7
0
8
0
S
W
24
1
Inhibited to use
0
2
0
3
Specified number
reception (ANTI
JUNK FAX)
reception (ANTI
JUNK FAX)
Used to set whether the FAX receive rejection function is made
valid or not for registered FAX numbers.
valid or not for registered FAX numbers.
Not set.
0
Refer to Main menu “ANTI
JUNK FAX”.
When a value outside the
set range is set, the initial
value is set.
JUNK FAX”.
When a value outside the
set range is set, the initial
value is set.
4
Bit No.
3
4
0
Not set.
0
0
Receive inhibit
0
1
5
Inhibited to use
0
6
Document output
setup in reception
setup in reception
Used to set the document output procedure; whether all the
received documents are collectively outputted after completion of
reception or every page is outputted when it is received.
received documents are collectively outputted after completion of
reception or every page is outputted when it is received.
Output after
reception of
reception of
every page
0
1: Collective output after
completion of reception
completion of reception
0: Output after reception of
every page
every page
7
Inhibited to use
0
8
Automatic
reduction print
reduction print
Used to set whether automatic reduction print is performed or not
so that a document longer than the fixed size and smaller than the
automatic reduction line number setting is printed on fixed size
paper.
so that a document longer than the fixed size and smaller than the
automatic reduction line number setting is printed on fixed size
paper.
Allow
1
Refer to User program
“AUTO RCV REDUCE”.
“AUTO RCV REDUCE”.
1: Allow
0: Inhibit
S
W
25
1
Minimum non-
divide reduce rate
divide reduce rate
The non-divide minimum reduce rate [%] = 100 - (3 x N)
N: 0 - 15 (Default: 10)
N: 0 - 15 (Default: 10)
70% (N=10)
1
2
0
3
1
4
0
5
Inhibited to use
0
6
0
7
0
8
0
SW
NO.
Data
No.
Item
Switch selection and contents of functions
Initial value
Remark
MX-FX12 FAX SOFT SWITCH 2 - 8
S
W
26
1
Read completion
sound
sound
Used to set whether buzzer sound is made or not when scan is
completed.
In manual send or when scan is completed in direct send, buzzer
sound is not made.
completed.
In manual send or when scan is completed in direct send, buzzer
sound is not made.
1sec.
0
1: Mute
0: 1sec.
2
Error beep of FAX
RX in case of the
sender fax is no
response
RX in case of the
sender fax is no
response
Setting of communication error beep when machine arrives as fax
reception, and fax signal is not received from sending side.
reception, and fax signal is not received from sending side.
Communication
error beep is
invalid
0
1: Communication error beep is
effective
effective
0: Communication error beep is
invalid
invalid
3
Speaker volume
setup
setup
Used to set speaker volume.
The following sounds are the targets of this setting.
• Alarm sound
The following sounds are the targets of this setting.
• Alarm sound
• Send end sound
• Receive end sound
• Scan end sound
Small
0
Refer to User program
“BEEPER VOLUME (send
completion sound / receive
completion sound / scan
completion sound / alarm
sound)”
“BEEPER VOLUME (send
completion sound / receive
completion sound / scan
completion sound / alarm
sound)”
4
Bit No.
3
4
1
Silent
0
0
Small
0
1
Medium
1
0
Large
1
1
5
Inhibited to use
0
6
0
7
0
8
0
S
W
27
1
Inhibited to use
0
2
0
3
0
4
0
5
0
6
0
7
Recording paper
tray selection
tray selection
Used to select the recording paper tray used by FAX.
Valid only when two cassettes are installed.
Valid only when two cassettes are installed.
AUTO
0
Refer to User program
“TRAY SELECTION”.
When a value outside the
set range is set, the initial
value is set.
“TRAY SELECTION”.
When a value outside the
set range is set, the initial
value is set.
Bit No.
7
8
8
AUTO
0
0
0
TRAY1
0
1
TRAY2
1
0
S
W
28
1
Inhibited to use
0
2
0
3
0
4
0
5
0
6
0
7
0
8
0
S
W
29
1
Number of auto
switch calls of
manual reception
auto reception
switch calls of
manual reception
auto reception
Used to set the number of calls to switch to auto receive in manual
receive mode.
receive mode.
0 time
0 Refer to User program
“# OF RINGS MANUAL RX”.
When a value outside the
set range is set, the initial
value is set.
When a value outside the
set range is set, the initial
value is set.
2
0
When set to 0, switch to auto receive is not made.
3
Binary input
0
Bit No.
1
2
3
4
4
Set range
0 to 9
0
Not switched when 0.
5
Setup of number
of times of call
rings
of times of call
rings
Used to set the number of calls before starting reception in auto
receive mode.
receive mode.
2 times
0 Refer to User program
“# OF RINGS AUTO RX”.
When a value outside the
set range is set, the initial
value is set.
When a value outside the
set range is set, the initial
value is set.
6
0
7
Setting is made in binary input.
1
Binary input
8
Bit No.
5
6
7
8
0
Set range
0 to 9 times
SW
NO.
Data
No.
Item
Switch selection and contents of functions
Initial value
Remark
MX-FX12 FAX SOFT SWITCH 2 - 9
S
W
30
1
Report output
when canceling
when canceling
Used to set whether the user cancel report is outputted or not when
send is canceled during document send.
send is canceled during document send.
Not output
0
1: Output
0: Not output
2
Inhibited to use
0
3
0
4
0
5
Default data,
sender print
sender print
Used to set whether sender information (registered in the sender
registration), sending date, and time are printed on the upper edge
of send document or not.
registration), sending date, and time are printed on the upper edge
of send document or not.
ON
1
1: ON
0: OFF
6
Report output
(in anti junk set.)
(in anti junk set.)
Use to whether the activity report is printed when anti-junk function
operates.
operates.
Print inhibited
0
1: Print
0: Print inhibited
7
Date/sender print
position setup
position setup
Used to set whether date/sender information is printed inside the
document area or outside the document area.
document area or outside the document area.
Outside of
document
0
1: Inside of document
0: Outside of document
8
Inhibited to use
0
S
W
31
1
Report output
(in transmission)
(in transmission)
Used to set whether communication report is outputted or not after
completion of sending (excluding sequential broadcast and
sequential send request).
completion of sending (excluding sequential broadcast and
sequential send request).
Only when
transmission is
failed.
1
Refer to User program
“PRINT SELECTION”.
When a value outside the
set range is set, the initial
value is set.
“PRINT SELECTION”.
When a value outside the
set range is set, the initial
value is set.
Bit No.
1
2
2
Print inhibited
0
0
0
All print
0
1
Only when transmission is
failed.
failed.
1
0
3
Report output
(In broadcast and
sequential send
request)
(In broadcast and
sequential send
request)
Used to set whether communication report is outputted or not after
completion of sending (sequential broadcast and sequential send
request).
completion of sending (sequential broadcast and sequential send
request).
All print
0
Refer to User program
“PRINT SELECTION”.
When a value outside the
set range is set, the initial
value is set.
“PRINT SELECTION”.
When a value outside the
set range is set, the initial
value is set.
Bit No.
3
4
4
Print inhibited
0
0
1
All print
0
1
Only the address to which
transmission is failed
transmission is failed
1
0
5
Report output
(in reception)
(in reception)
Used to set whether communication report is outputted or not in
reception.
reception.
Print inhibited
0
Refer to User program
“PRINT SELECTION”.
When a value outside the
set range is set, the initial
value is set.
“PRINT SELECTION”.
When a value outside the
set range is set, the initial
value is set.
Bit No.
5
6
6
Print inhibited
0
0
0
All print
0
1
Only in error
1
0
7
Contents of send
document are
printed in memory
send
document are
printed in memory
send
Used to set whether part of send document is printed on the
communication report or not in memory send.
communication report or not in memory send.
Only the address
to which
transmission is
failed
1
Refer to User program
“PRINT SELECTION”.
When a value outside the
set range is set, the initial
value is set.
“PRINT SELECTION”.
When a value outside the
set range is set, the initial
value is set.
Bit No.
7
8
8
Print inhibited
0
0
0
All print
0
1
Only the address to which
transmission is failed
transmission is failed
1
0
S
W
32
1
Distinctive ringing
(U.S.A., Canada,
Australia, New
Zealand)
(U.S.A., Canada,
Australia, New
Zealand)
Used to set the ringing pattern as FAX reception.
OFF
0
Refer to User program
“DISTINCTIVE RING”.
When a value outside the
set range is set, the initial
value is set.
*1: For U.S.A., Canada
“DISTINCTIVE RING”.
When a value outside the
set range is set, the initial
value is set.
*1: For U.S.A., Canada
only
Bit No.
1
2
3
4
2
OFF
0
0
0
0
0
Standard/ON
0
0
0
1
3
Pattern 1 *
1
1
0
0
0
0
Pattern 2 *
1
0
1
0
0
4
Pattern 3 *
1
1
1
0
0
0
Pattern 4 *
1
0
0
1
0
Pattern 5 *
1
1
0
1
0
5
Inhibited to use
0
6
Index print setup
Used to set whether the index is printed when outputting received
document or not.
document or not.
Not print
0
Refer to User program
“INDEX PRINT”.
“INDEX PRINT”.
1: Print
0: Not print
7
Inhibited to use
0
8
0
SW
NO.
Data
No.
Item
Switch selection and contents of functions
Initial value
Remark
MX-FX12 FAX SOFT SWITCH 2 - 10
S
W
33
1
Page number print
setup
setup
Used to set whether the page number is added to the sender
information print or not.
information print or not.
Yes
1
1: Yes
0: No
2
Inhibited to use
0
3
0
4
0
5
0
6
0
7
0
8
Reception data
duplex print
duplex print
Used to set whether duplex print of received data is made or not.
No
0
Refer to User program
“DUPLEX RCV”.
“DUPLEX RCV”.
1: Yes
0: No
S
W
34
1
Flash send wait
time (U.S.A.,
Canada, U.K.,
Netherlands,
Luxembourg,
Belgium, France,
Australia, New
Zealand: Inhibited
to use)
time (U.S.A.,
Canada, U.K.,
Netherlands,
Luxembourg,
Belgium, France,
Australia, New
Zealand: Inhibited
to use)
Used to set the time from off-hook to Flash send.
1sec.
0
Bit No.
1
2
0sec.
0
0
0.5sec.
0
1
2
1sec.
1
0
0
2sec.
1
1
3
Inhibited to use
0
4
0
5
Signal send level
Max.
Max.
Used to set the max. signal send level.
Binary input
Binary input
–8dBm
1
6
0
7
Bit No.
Set range
Set range
5
6
7
8
0 (0dBm) to 15 (–15dBm)
0
8
0
S
W
35
1
Cover function
default setup
default setup
Used to set whether cover is added as default or not.
When auto clear is made by pressing [Clear All] key, the machine
returns to this setting.
When auto clear is made by pressing [Clear All] key, the machine
returns to this setting.
No
0
1: Yes
0: No
2
Answering
machine
connection
machine
connection
Setting to make them connect telephone that has answering
machine function as external telephone, and unite answering
machine function to fax receiver function.
When an absent function of an external telephone is used, it sets it
to “ON”.
The setting simultaneously with the dial-in function is improper.
machine function as external telephone, and unite answering
machine function to fax receiver function.
When an absent function of an external telephone is used, it sets it
to “ON”.
The setting simultaneously with the dial-in function is improper.
ON
1
1: ON
0: Off
3
CI delete max.
OFF time
OFF time
Used to set the max. wait time between detection of CI signal
pulse (number of times) and detection of the next CI signal
pulse.
pulse (number of times) and detection of the next CI signal
pulse.
If CIK signal pulse is not detected within this time, the number of
calls up to that time is cleared.
calls up to that time is cleared.
5sec.
0
4
Bit No.
3
4
0
5sec.
0
0
10sec.
0
1
15sec.
1
0
20sec.
1
1
5
Answering
machine call
number setting
machine call
number setting
Used to set the number of calls to switch to auto receive when
answering telephone is not called in when the receive mode is set
to the answering telephone connection mode.
Setting is made in binary input.
Binary input
answering telephone is not called in when the receive mode is set
to the answering telephone connection mode.
Setting is made in binary input.
Binary input
5 times
0
6
1
7
0
Bit No.
Set range
Set range
5
6
7
8
0 to 15 times
8
1
S
W
36
1
CNG detection
completion time
completion time
Used to set the time for completion of CNG signal/mute detection in
the answering telephone connection mode.
Count is made from the last call signal.
the answering telephone connection mode.
Count is made from the last call signal.
45sec.
0 When a value outside the
set range is set, the initial
value is set.
value is set.
2
0
3
1
4
Setting is made in binary input.
0
5
Binary input
1
6
Bit No.
Set range
Set range
1
2
3
4
5
6
7
8
1 to 255sec.
1
7
0
8
1
SW
NO.
Data
No.
Item
Switch selection and contents of functions
Initial value
Remark
Click on the first or last page to see other MX-B201D (serv.man6) service manuals if exist.