Sharp MX-AP14 Service Manual ▷ View online
MX-AP14 UNPACKING AND INSTALLATION 3 – 8
2)
Push [BOOT/SHUTDOWN] button one time to boot up the
Main unit. While booting, power indicator lamp blinks in green,
and then lamp will be solid green after boot up completes.
Main unit. While booting, power indicator lamp blinks in green,
and then lamp will be solid green after boot up completes.
3)
Plug in of MFP and turning power main switch on and turning
switch power on of the operation panel of MFP.
switch power on of the operation panel of MFP.
4)
In case of turning power off of Main unit, push one time to
[BOOT/SHUTDOWN] button (within 1 sec) Main unit has
stopped, power indicator lamp is lights off.
[BOOT/SHUTDOWN] button (within 1 sec) Main unit has
stopped, power indicator lamp is lights off.
5)
Turning power off of the Main unit.
6)
Plug off of the Main unit.
4. Installation (MX-M654N/M754N)
Before installation, be sure to turn both the operation and main
power switches off and disconnect the power plug from the power
outlet. Make double sure that the data lamp on the operation panel
does not light up or blink when performing installation.
power switches off and disconnect the power plug from the power
outlet. Make double sure that the data lamp on the operation panel
does not light up or blink when performing installation.
A. Install RS-232C interface
1)
Remove the screw and the right rear cover.
2)
Cut the line of the cover from back side.
3)
Remove the screws and pull out the MFP PWB unit.
Ĭ
ĭ
Ĭ
ĭ
Į
1
: ‘15/Apr
1
MX-AP14 UNPACKING AND INSTALLATION 3 – 9
4)
Install RS-232C Unit (Packed item No.10) to MFP PWB Unit.
Put the connector through the MFP PWB Unit and fix with RIC
fixing screw. (Packed item No.12)
Put the connector through the MFP PWB Unit and fix with RIC
fixing screw. (Packed item No.12)
5)
Wind up harness into a ring form where head of a connector
aligns with right side of U character hole in USB metal plate
and then tie up with cable tie (Packed item No.7). Cut extra tail
for cable tie.
aligns with right side of U character hole in USB metal plate
and then tie up with cable tie (Packed item No.7). Cut extra tail
for cable tie.
6)
Connect the cable to the MFP PWB.
Ring form made by procedure 5) should be shown below.
Ring form made by procedure 5) should be shown below.
7)
Put MFP PWB back to the MFP and all the covers removed.
B. Install the Main unit to the MFP
1)
Fix the damper (Packed item No.3 of installing kit) to the rear
cover with the screws. (Packed item No.4)
cover with the screws. (Packed item No.4)
2)
Tighten the screws (Packed item No.12) lightly on the fixing
plate. (Packed item No.1, 2 of installing lit)
plate. (Packed item No.1, 2 of installing lit)
3)
Set the upper damper to the top hole and fit the lower damper
into the bottom hole of the fixing plate. (Do the same for both
sides)
into the bottom hole of the fixing plate. (Do the same for both
sides)
OK
NG
EWVXKGY
OK
NG
Note:
Use the inner hole
Use the inner hole
1
: ‘15/Apr
1
MX-AP14 UNPACKING AND INSTALLATION 3 – 10
4)
Attach the locking saddle (Packed item No.6) to the Main unit.
5)
Mount the main unit (Packed item No.1) to the screws on the
fixing plate.
fixing plate.
6)
Fix the main unit with the step screws. (Packed item No.5 of
installing kit and step5)
installing kit and step5)
C. Connector connection
1)
Connect with LAN cable (Packed item No.5) between MFP
and main unit (upper port).
and main unit (upper port).
2)
Put the LAN cable to the locking saddle as shown below.
3)
Connect with RS-232C cable (Packed item No.4) between the
MFP and main unit.
NOTE: Do not connect RS-232C cable to this port.
MFP and main unit.
NOTE: Do not connect RS-232C cable to this port.
4)
Put the RS-232C cable to the locking saddle then locked.
A
Ĭĭ
Į
Note:
Make sure that the resin parts (A)
mounted to the plates (1), (2) is fit
into the groove of the damper (3)
Make sure that the resin parts (A)
mounted to the plates (1), (2) is fit
into the groove of the damper (3)
※Connect to
upper of 2 port
upper of 2 port
(NOTE)
Do not connect
Do not connect
1
: ‘15/Apr
1
MX-AP14 UNPACKING AND INSTALLATION 3 – 11
5)
Connect with Power cord (Packed item No.2), and connect
Power cord fixing (Packed item No.3) to the Main unit.
Power cord fixing (Packed item No.3) to the Main unit.
6)
Put power cord fixing to the power cord.
D. Turning power on
1)
Plug in and turning power on of the Main unit .
2)
Push [BOOT/SHUTDOWN] button one time to boot up the
Main unit. While booting, power indicator lamp blinks in green,
and then lamp will be solid green after boot up completes.
Main unit. While booting, power indicator lamp blinks in green,
and then lamp will be solid green after boot up completes.
3)
Plug in of MFP and turning power main switch on and turning
switch power on of the operation panel of MFP.
switch power on of the operation panel of MFP.
4)
In case of turning power off of Main unit, push one time to
[BOOT/SHUTDOWN] button (within 1 sec) Main unit has
stopped, power indicator lamp is lights off.
[BOOT/SHUTDOWN] button (within 1 sec) Main unit has
stopped, power indicator lamp is lights off.
5)
Turning power off of the Main unit.
6)
Plug off of the Main unit.
OFF
ON
1
: ‘15/Apr
1
Click on the first or last page to see other MX-AP14 service manuals if exist.