Sharp MX-7090N / MX-8090N (serv.man3) Service Manual ▷ View online
MX-8090N Transit, Installation (using) environment, Note - ii
Operational environment
Temperature: 10 to 35 degrees C
Humidity: 20 to 85% RH
Atmospheric pressure: 590 to 1013hPa (altitude: 0 to 2000 m)
(2)
Contaminates
If dust enters the machine, it may cause dirty copy and a paper
jam, resulting in a shortened lifetime.
jam, resulting in a shortened lifetime.
(3)
Direct sunlight
If the machine is installed under the rays of the sun, the exterior of
the machine may be discolored and abnormal copies may be pro-
duced.
the machine may be discolored and abnormal copies may be pro-
duced.
(4)
Gases and chemicals
Do not install the machine at a place where there are gases and
chemicals. Especially be careful to avoid installation near a diazo-
type copier, which produces ammonium gas.
chemicals. Especially be careful to avoid installation near a diazo-
type copier, which produces ammonium gas.
Copy quality may be adversely affected and a trouble may be
caused.
caused.
* There was a trouble in a place where silicon-series gas or volatile
components are generated. Use great care for avoiding this.
(5)
Vibration
Avoid installation near a machine which produces vibrations.
If vibrations are applied to the copier machine, copy images may be
deflected and a trouble may be caused.
deflected and a trouble may be caused.
F. Note for handling PWB and electronic parts
When handling the PWB and the electronic parts, be sure to
observe the following precautions in order to prevent against dam-
age by static electricity.
observe the following precautions in order to prevent against dam-
age by static electricity.
• When in transit or storing, put the parts in an anti-static bag or an
anti-static case and do not touch them with bare hands.
• When and after removing the parts from an anti-static bag (case),
use an earth band as shown below:
• Put an earth band to your arm, and connect it to the machine.
85%
Humidity㧔RH㧕
60%
20%
MX-8090N Transit, Installation (using) environment, Note - iii
• When repairing or replacing an electronic part, perform the
procedure on an anti-static mat.
G. Note for proper drum, developing, fusing and
transfer unit handling
When handling the OPC drum, developing and transfer units,
observe the following items.
observe the following items.
Drum unit
• To prevent damage to the OPC drum, avoid working on the drum
unit in high intensity light areas.
• When the OPC drum is removed from the machine, cover it with
light blocking material. (When using paper, use about 10 sheets
of paper to cover it.)
of paper to cover it.)
• Be careful not to attach fingerprints, oil, grease, or other foreign
material on the OPC drum surface.
Transfer unit
• Be careful not to "leave” fingerprints, oil, grease, or other foreign
material on the transfer roller, primary transfer belt and second-
ary transfer belt.
ary transfer belt.
Developing unit
• Be careful not to "leave” fingerprints, oil, grease, or other foreign
material on the developing unit.
Fusing unit
• Be careful not to "leave” fingerprints, oil, grease, or other foreign
material on the fusing roller and the external heating belt.
• Do not leave the fusing roller in contact state for a long time.
If these items are neglected, a trouble may be generated in the
copy and print image quality.
copy and print image quality.
2. Transit and delivery
A. Implements, facility, and manpower
It is recommendable to use a forklift for bringing in the machine for
safety.
safety.
If no forklift is available, man-power of two persons is required. The
machine is considerably heavy, and requires safety precautions for
delivery and installation.
machine is considerably heavy, and requires safety precautions for
delivery and installation.
Transit of the machine must be made in packed condition to the
installing place.
installing place.
Since the hard disk drive is built in the machine, use care not to
exert vibrations or shocks to the machine when in transit.
exert vibrations or shocks to the machine when in transit.
B. Delivery
Remove the packing materials prior to installation in the office envi-
ronment.
ronment.
No.
Content
Method
1
Implements, facility,
and man power
and man power
Use a forklift. (If no forklift is available,
manpower of two persons is required.)
manpower of two persons is required.)
2
Delivery
Transit must be made in packed condition.
MX-8090N Transit, Installation (using) environment, Note - iv
3. Power configuration
A. Indoor wiring (power outlet) and breaker information
NOTE:
• Prepare an indoor wiring (power outlet) which is connected to the AC plug of the machine and its option units.
The required number of power outlets varies according to the combination of the option units.
Prepare the necessary number of them.
Prepare the necessary number of them.
Example: (North America) Finisher "2.9A", large-capacity multi-stage tray "8A" 12A>10.9A=2.9A+8A Connectable to the same circuit
(breaker).
(breaker).
• For the AC cord of an option unit, use another indoor wiring (another breaker) than that for the machine.
For North America only
• The machine power is of 200V, an indoor wiring work may be required.
For Europe only
• Both of AC code 1 and 2 can be connected together into 16A AC outlet in case, but if the power source is less than 16A in case, notice the
following rules.
For additional installation of breakers and 200V indoor wiring, use professionals to do the jobs.
MX-FN21/22
MX-ST10
Main Machine 1
Main Machine 2
MX-LC13 N
AC cord type
Inlet
Inlet
Direct
---
Inlet
North
America
America
70cpm
machine
80cpm
machine
machine
80cpm
machine
Power supply
rating
rating
120V/2.9A
120V/1.3A
208-240V/12A
---
120V/8A
Power capacity
120V/15A
120V/20A
240V/20A
---
120V/15A
Form of the
plug
plug
---
Form of the
power outlet
power outlet
---
MX-FN21/22
MX-ST10
Main Machine 1
Main Machine 2
MX-LC13 N
AC cord type
Inlet
Inlet
Inlet
Inlet
Inlet
Europe/
UK
UK
70cpm
machine
80cpm
machine
machine
80cpm
machine
Power supply
rating
rating
230V/1.5A
120V/1.3A
230V/8A
230V/8A
230V/4A
Power capacity
230V/10A
230V/20A
230V/15A
230V/15A
230V/10A
Form of the
plug
plug
Form of the
power outlet
power outlet
MX-ST10
-8
2"
MX-ST10
MX-RB13
MX-FN22
-8
2"
-8
,#
-8
,#
%XCEPT
MX-8090N CONFIGURATION 1 – 1
MX-8090N
Service Manual
[1] CONFIGURATION
1. System diagram
MX-8090N
MX-7090N
DIGITAL FULL COLOR
MULTIFUNCTIONAL SYSTEM
MULTIFUNCTIONAL SYSTEM
MX-LC12
LARGE CAPACITY TRAY
MX-MF10
MULTI BYPASS TRAY
MX-TR14
EXIT TRAY UNIT
MX-LCX3 N
MX-MF11
MULTI BYPASS TRAY
MX-RB14
PAPER PASS UNIT
MX-RB15
CURL CORRECTION
UNIT
UNIT
MX-CF11
INSERTER
MX-RB12 N
P APER P ASS
UNIT
UNIT
MX-TU14
EXIT TRAY CABINET
MX-LC13 N
MX-ST10
HIGH CAP
A CITY
ST A CKER
MX-CA10
P
APER CAR T
MX-CA10
P
APER CAR T
MX-ST10
HIGH CAP
A CITY
ST A CKER
MX-FD10
FOLDING UNIT
MX-PN13
A/B/C/D
PUNCH
MODULE
MODULE
MX-FN22
SADDLE STTICH
FINISHER
FINISHER
MX-FN21
FINISHER
MX-TM10
TRIMMING
MODULE
MODULE
MX-FD10
FOLDING UNIT
MX-RB13
RELA Y UNIT
MX-PN13
A/B/C/D
PUNCH
MODULE
MODULE
MX-FN22
SADDLE STTICH
FINISHER
FINISHER
MX-FN21
FINISHER
MX-TM10
TRIMMING
MODULE
MODULE
MX-PN13
A/B/C/D
PUNCH
MODULE
MODULE
MX-PX12
INTERFACE KIT
MX-LT10
LONG PAPER
FEEDING TRAY
FEEDING TRAY
MX -RB17
*1
CONNECTION
MODULE
MODULE
*1: Option for 2nd MX-LC13
MX-PF10
BARCODE FONT KIT
AR-SU1
STAMP UNIT
MX-SCX1
STAPLE CARTRIDGE
MX-SCX2
(For Saddle)
(For 100 sheets stapleing)
MX-PE14
FIERY SERVER
MX-PX13
INTERFACE KIT
MX-PE13
FIERY SERVER
MX-AMX1
APPLICATION
INTEGRATION MODULE
INTEGRATION MODULE
MX-AMX2
APPLICATION
COMMUNICATION MODULE
COMMUNICATION MODULE
MX-AMX3
EXTERNAL ACCOUNT
MODULE
MODULE
MX-SL10N
STATUS INDICATOR
LARGE CAPACITY TRAY
LARGE CAPACITY TRAYS
STAPLE CARTRIDGE
MX-KB16
KEYBOARD
Click on the first or last page to see other MX-7090N / MX-8090N (serv.man3) service manuals if exist.