Sharp MX-6500N / MX-7500N (serv.man120) Service Manual / Technical Bulletin ▷ View online
Sharp Electronics (UK) Ltd., Technical Services Group
CCE-1413
[Description]
No.
Item
Details
1
Main unit control
Following settings have been added to the Detail tab in Paper Settings.
1) Motor Speed Setting
2) Registration Adjustment (Manual)
3) Maximum Density Setting
Setting range of Paper Settings has been expanded as listed below:
1) Fusing Temperature Settings (Old: -10 to 10/ New: -20 to 20)
2) Primary Transfer Setting (Old: -20 to 20/ New: -30 to 30)
3) Secondary Transfer Setting (Old: -20 to 20/ New: -30 to 30)
4) PTC Current Value Setting (Old: -30 to 30 / New: -40 to 40)
5) Settable weight of Coated Paper (Gloss) and Coated Paper (Matt) (Old: 55 to 256g/m²
/ New: 55 to 300g/m²)
1) Motor Speed Setting
2) Registration Adjustment (Manual)
3) Maximum Density Setting
Setting range of Paper Settings has been expanded as listed below:
1) Fusing Temperature Settings (Old: -10 to 10/ New: -20 to 20)
2) Primary Transfer Setting (Old: -20 to 20/ New: -30 to 30)
3) Secondary Transfer Setting (Old: -20 to 20/ New: -30 to 30)
4) PTC Current Value Setting (Old: -30 to 30 / New: -40 to 40)
5) Settable weight of Coated Paper (Gloss) and Coated Paper (Matt) (Old: 55 to 256g/m²
/ New: 55 to 300g/m²)
2
Main unit control
Custom size paper output has been allowed upon the setting of "Edge-to-Edge Printing"
on printer driver.
This allows the more appropriate "Edge-to-Edge Printing" on fixed size paper.
on printer driver.
This allows the more appropriate "Edge-to-Edge Printing" on fixed size paper.
3
Main unit control
Modification has been made so that when Saddle Stitch and Trimming are set for output
of one sheet to the machine with MX-FN22, the paper is trimmed but no saddle stitch is
performed.
of one sheet to the machine with MX-FN22, the paper is trimmed but no saddle stitch is
performed.
4
Main unit control
Correction of failure to match the print position on side 1 and 2 of SRA3 paper.
The failure occurred after the print position adjustment.
The failure occurred after the print position adjustment.
5
Main unit control
Correction of failure to output paper onto Right tray when Booklet maker and Right tray
are mounted.
are mounted.
6
Main unit control
Remedy of the problem with colour change which occurs in the midst of printing.
*You don't see any improvement just by upgrading the firmware. Please execute Colour
Balance adjustment at the time of firmware upgrade as may be necessary.
*You don't see any improvement just by upgrading the firmware. Please execute Colour
Balance adjustment at the time of firmware upgrade as may be necessary.
7
Main unit control
Modification of a problem which occurs with following steps: 1) Print out a test pattern in
Paper Settings from Bypass tray in duplex. 2) The Bypass tray gets empty 3) Add papers
to the bypass tray. 4) The test pattern is printed in simplex.
Paper Settings from Bypass tray in duplex. 2) The Bypass tray gets empty 3) Add papers
to the bypass tray. 4) The test pattern is printed in simplex.
8
Main unit control
Modification has been made so that one User Type setting can be applied to more than
one tray. This allows auto tray change in case of tray empty.
one tray. This allows auto tray change in case of tray empty.
9
Main unit control
The paper weight allowed for feeding from bypass tray on LCT has been expanded to
300g/m².
Also Heavy Paper 3, Heavy Paper 4, Glossy Paper, Labels and Embossed are allowed
to select as Paper Type.
300g/m².
Also Heavy Paper 3, Heavy Paper 4, Glossy Paper, Labels and Embossed are allowed
to select as Paper Type.
10 Main unit control
"Side1/2, XY Ratio Settings" is no more displayed on Paper Settings registration screen
on installation of Fiery because the magnification adjustment cannot be reflected.
on installation of Fiery because the magnification adjustment cannot be reflected.
11 Main unit control
Multi-level print speed setting has been implemented to increase the print speed of
custom size paper. The speed varies depends on the paper size.
custom size paper. The speed varies depends on the paper size.
12 Main unit control
Followings have been changed to improve the registration level:
(1) The timing to perform the registration adjustment
(2) Default value of AG in SIM44-28 to perform the registration adjustment when
necessary.
SIM44-28 AG(RG_PERM_TIMER): Changed from 1 to 0.
*Default value won't change just by upgrading the firmware. Please change the value of
AG in SIM44-28 at the time of firmware upgrade. In addition, execute SIM50-22 if
necessary.
(1) The timing to perform the registration adjustment
(2) Default value of AG in SIM44-28 to perform the registration adjustment when
necessary.
SIM44-28 AG(RG_PERM_TIMER): Changed from 1 to 0.
*Default value won't change just by upgrading the firmware. Please change the value of
AG in SIM44-28 at the time of firmware upgrade. In addition, execute SIM50-22 if
necessary.
Sharp Electronics (UK) Ltd., Technical Services Group
CCE-1413
[Description]
No.
Item
Details
1
Main unit control
Following settings have been added to the Detail tab in Paper Settings.
1) Motor Speed Setting
2) Registration Adjustment (Manual)
3) Maximum Density Setting
Setting range of Paper Settings has been expanded as listed below:
1) Fusing Temperature Settings (Old: -10 to 10/ New: -20 to 20)
2) Primary Transfer Setting (Old: -20 to 20/ New: -30 to 30)
3) Secondary Transfer Setting (Old: -20 to 20/ New: -30 to 30)
4) PTC Current Value Setting (Old: -30 to 30 / New: -40 to 40)
5) Settable weight of Coated Paper (Gloss) and Coated Paper (Matt) (Old: 55 to 256g/m²
/ New: 55 to 300g/m²)
1) Motor Speed Setting
2) Registration Adjustment (Manual)
3) Maximum Density Setting
Setting range of Paper Settings has been expanded as listed below:
1) Fusing Temperature Settings (Old: -10 to 10/ New: -20 to 20)
2) Primary Transfer Setting (Old: -20 to 20/ New: -30 to 30)
3) Secondary Transfer Setting (Old: -20 to 20/ New: -30 to 30)
4) PTC Current Value Setting (Old: -30 to 30 / New: -40 to 40)
5) Settable weight of Coated Paper (Gloss) and Coated Paper (Matt) (Old: 55 to 256g/m²
/ New: 55 to 300g/m²)
2
Main unit control
Custom size paper output has been allowed upon the setting of "Edge-to-Edge Printing"
on printer driver.
This allows the more appropriate "Edge-to-Edge Printing" on fixed size paper.
on printer driver.
This allows the more appropriate "Edge-to-Edge Printing" on fixed size paper.
3
Main unit control
Modification has been made so that when Saddle Stitch and Trimming are set for output
of one sheet to the machine with MX-FN22, the paper is trimmed but no saddle stitch is
performed.
of one sheet to the machine with MX-FN22, the paper is trimmed but no saddle stitch is
performed.
4
Main unit control
Correction of failure to match the print position on side 1 and 2 of SRA3 paper.
The failure occurred after the print position adjustment.
The failure occurred after the print position adjustment.
5
Main unit control
Correction of failure to output paper onto Right tray when Booklet maker and Right tray
are mounted.
are mounted.
6
Main unit control
Remedy of the problem with colour change which occurs in the midst of printing.
*You don't see any improvement just by upgrading the firmware. Please execute Colour
Balance adjustment at the time of firmware upgrade as may be necessary.
*You don't see any improvement just by upgrading the firmware. Please execute Colour
Balance adjustment at the time of firmware upgrade as may be necessary.
7
Main unit control
Modification of a problem which occurs with following steps: 1) Print out a test pattern in
Paper Settings from Bypass tray in duplex. 2) The Bypass tray gets empty 3) Add papers
to the bypass tray. 4) The test pattern is printed in simplex.
Paper Settings from Bypass tray in duplex. 2) The Bypass tray gets empty 3) Add papers
to the bypass tray. 4) The test pattern is printed in simplex.
8
Main unit control
Modification has been made so that one User Type setting can be applied to more than
one tray. This allows auto tray change in case of tray empty.
one tray. This allows auto tray change in case of tray empty.
9
Main unit control
The paper weight allowed for feeding from bypass tray on LCT has been expanded to
300g/m².
Also Heavy Paper 3, Heavy Paper 4, Glossy Paper, Labels and Embossed are allowed
to select as Paper Type.
300g/m².
Also Heavy Paper 3, Heavy Paper 4, Glossy Paper, Labels and Embossed are allowed
to select as Paper Type.
10 Main unit control
"Side1/2, XY Ratio Settings" is no more displayed on Paper Settings registration screen
on installation of Fiery because the magnification adjustment cannot be reflected.
on installation of Fiery because the magnification adjustment cannot be reflected.
11 Main unit control
Multi-level print speed setting has been implemented to increase the print speed of
custom size paper. The speed varies depends on the paper size.
custom size paper. The speed varies depends on the paper size.
12 Main unit control
Followings have been changed to improve the registration level:
(1) The timing to perform the registration adjustment
(2) Default value of AG in SIM44-28 to perform the registration adjustment when
necessary.
SIM44-28 AG(RG_PERM_TIMER): Changed from 1 to 0.
*Default value won't change just by upgrading the firmware. Please change the value of
AG in SIM44-28 at the time of firmware upgrade. In addition, execute SIM50-22 if
necessary.
(1) The timing to perform the registration adjustment
(2) Default value of AG in SIM44-28 to perform the registration adjustment when
necessary.
SIM44-28 AG(RG_PERM_TIMER): Changed from 1 to 0.
*Default value won't change just by upgrading the firmware. Please change the value of
AG in SIM44-28 at the time of firmware upgrade. In addition, execute SIM50-22 if
necessary.
Sharp Electronics (UK) Ltd., Technical Services Group
CCE-1413
[Description]
No.
Item
Details
1
Main unit control
Following settings have been added to the Detail tab in Paper Settings.
1) Motor Speed Setting
2) Registration Adjustment (Manual)
3) Maximum Density Setting
Setting range of Paper Settings has been expanded as listed below:
1) Fusing Temperature Settings (Old: -10 to 10/ New: -20 to 20)
2) Primary Transfer Setting (Old: -20 to 20/ New: -30 to 30)
3) Secondary Transfer Setting (Old: -20 to 20/ New: -30 to 30)
4) PTC Current Value Setting (Old: -30 to 30 / New: -40 to 40)
5) Settable weight of Coated Paper (Gloss) and Coated Paper (Matt) (Old: 55 to 256g/m²
/ New: 55 to 300g/m²)
1) Motor Speed Setting
2) Registration Adjustment (Manual)
3) Maximum Density Setting
Setting range of Paper Settings has been expanded as listed below:
1) Fusing Temperature Settings (Old: -10 to 10/ New: -20 to 20)
2) Primary Transfer Setting (Old: -20 to 20/ New: -30 to 30)
3) Secondary Transfer Setting (Old: -20 to 20/ New: -30 to 30)
4) PTC Current Value Setting (Old: -30 to 30 / New: -40 to 40)
5) Settable weight of Coated Paper (Gloss) and Coated Paper (Matt) (Old: 55 to 256g/m²
/ New: 55 to 300g/m²)
2
Main unit control
Custom size paper output has been allowed upon the setting of "Edge-to-Edge Printing"
on printer driver.
This allows the more appropriate "Edge-to-Edge Printing" on fixed size paper.
on printer driver.
This allows the more appropriate "Edge-to-Edge Printing" on fixed size paper.
3
Main unit control
Modification has been made so that when Saddle Stitch and Trimming are set for output
of one sheet to the machine with MX-FN22, the paper is trimmed but no saddle stitch is
performed.
of one sheet to the machine with MX-FN22, the paper is trimmed but no saddle stitch is
performed.
4
Main unit control
Correction of failure to match the print position on side 1 and 2 of SRA3 paper.
The failure occurred after the print position adjustment.
The failure occurred after the print position adjustment.
5
Main unit control
Correction of failure to output paper onto Right tray when Booklet maker and Right tray
are mounted.
are mounted.
6
Main unit control
Remedy of the problem with colour change which occurs in the midst of printing.
*You don't see any improvement just by upgrading the firmware. Please execute Colour
Balance adjustment at the time of firmware upgrade as may be necessary.
*You don't see any improvement just by upgrading the firmware. Please execute Colour
Balance adjustment at the time of firmware upgrade as may be necessary.
7
Main unit control
Modification of a problem which occurs with following steps: 1) Print out a test pattern in
Paper Settings from Bypass tray in duplex. 2) The Bypass tray gets empty 3) Add papers
to the bypass tray. 4) The test pattern is printed in simplex.
Paper Settings from Bypass tray in duplex. 2) The Bypass tray gets empty 3) Add papers
to the bypass tray. 4) The test pattern is printed in simplex.
8
Main unit control
Modification has been made so that one User Type setting can be applied to more than
one tray. This allows auto tray change in case of tray empty.
one tray. This allows auto tray change in case of tray empty.
9
Main unit control
The paper weight allowed for feeding from bypass tray on LCT has been expanded to
300g/m².
Also Heavy Paper 3, Heavy Paper 4, Glossy Paper, Labels and Embossed are allowed
to select as Paper Type.
300g/m².
Also Heavy Paper 3, Heavy Paper 4, Glossy Paper, Labels and Embossed are allowed
to select as Paper Type.
10 Main unit control
"Side1/2, XY Ratio Settings" is no more displayed on Paper Settings registration screen
on installation of Fiery because the magnification adjustment cannot be reflected.
on installation of Fiery because the magnification adjustment cannot be reflected.
11 Main unit control
Multi-level print speed setting has been implemented to increase the print speed of
custom size paper. The speed varies depends on the paper size.
custom size paper. The speed varies depends on the paper size.
12 Main unit control
Followings have been changed to improve the registration level:
(1) The timing to perform the registration adjustment
(2) Default value of AG in SIM44-28 to perform the registration adjustment when
necessary.
SIM44-28 AG(RG_PERM_TIMER): Changed from 1 to 0.
*Default value won't change just by upgrading the firmware. Please change the value of
AG in SIM44-28 at the time of firmware upgrade. In addition, execute SIM50-22 if
necessary.
(1) The timing to perform the registration adjustment
(2) Default value of AG in SIM44-28 to perform the registration adjustment when
necessary.
SIM44-28 AG(RG_PERM_TIMER): Changed from 1 to 0.
*Default value won't change just by upgrading the firmware. Please change the value of
AG in SIM44-28 at the time of firmware upgrade. In addition, execute SIM50-22 if
necessary.
Sharp Electronics (UK) Ltd., Technical Services Group
CCE-1413
[Description]
No.
Item
Details
1
Main unit control
Following settings have been added to the Detail tab in Paper Settings.
1) Motor Speed Setting
2) Registration Adjustment (Manual)
3) Maximum Density Setting
Setting range of Paper Settings has been expanded as listed below:
1) Fusing Temperature Settings (Old: -10 to 10/ New: -20 to 20)
2) Primary Transfer Setting (Old: -20 to 20/ New: -30 to 30)
3) Secondary Transfer Setting (Old: -20 to 20/ New: -30 to 30)
4) PTC Current Value Setting (Old: -30 to 30 / New: -40 to 40)
5) Settable weight of Coated Paper (Gloss) and Coated Paper (Matt) (Old: 55 to 256g/m²
/ New: 55 to 300g/m²)
1) Motor Speed Setting
2) Registration Adjustment (Manual)
3) Maximum Density Setting
Setting range of Paper Settings has been expanded as listed below:
1) Fusing Temperature Settings (Old: -10 to 10/ New: -20 to 20)
2) Primary Transfer Setting (Old: -20 to 20/ New: -30 to 30)
3) Secondary Transfer Setting (Old: -20 to 20/ New: -30 to 30)
4) PTC Current Value Setting (Old: -30 to 30 / New: -40 to 40)
5) Settable weight of Coated Paper (Gloss) and Coated Paper (Matt) (Old: 55 to 256g/m²
/ New: 55 to 300g/m²)
2
Main unit control
Custom size paper output has been allowed upon the setting of "Edge-to-Edge Printing"
on printer driver.
This allows the more appropriate "Edge-to-Edge Printing" on fixed size paper.
on printer driver.
This allows the more appropriate "Edge-to-Edge Printing" on fixed size paper.
3
Main unit control
Modification has been made so that when Saddle Stitch and Trimming are set for output
of one sheet to the machine with MX-FN22, the paper is trimmed but no saddle stitch is
performed.
of one sheet to the machine with MX-FN22, the paper is trimmed but no saddle stitch is
performed.
4
Main unit control
Correction of failure to match the print position on side 1 and 2 of SRA3 paper.
The failure occurred after the print position adjustment.
The failure occurred after the print position adjustment.
5
Main unit control
Correction of failure to output paper onto Right tray when Booklet maker and Right tray
are mounted.
are mounted.
6
Main unit control
Remedy of the problem with colour change which occurs in the midst of printing.
*You don't see any improvement just by upgrading the firmware. Please execute Colour
Balance adjustment at the time of firmware upgrade as may be necessary.
*You don't see any improvement just by upgrading the firmware. Please execute Colour
Balance adjustment at the time of firmware upgrade as may be necessary.
7
Main unit control
Modification of a problem which occurs with following steps: 1) Print out a test pattern in
Paper Settings from Bypass tray in duplex. 2) The Bypass tray gets empty 3) Add papers
to the bypass tray. 4) The test pattern is printed in simplex.
Paper Settings from Bypass tray in duplex. 2) The Bypass tray gets empty 3) Add papers
to the bypass tray. 4) The test pattern is printed in simplex.
8
Main unit control
Modification has been made so that one User Type setting can be applied to more than
one tray. This allows auto tray change in case of tray empty.
one tray. This allows auto tray change in case of tray empty.
9
Main unit control
The paper weight allowed for feeding from bypass tray on LCT has been expanded to
300g/m².
Also Heavy Paper 3, Heavy Paper 4, Glossy Paper, Labels and Embossed are allowed
to select as Paper Type.
300g/m².
Also Heavy Paper 3, Heavy Paper 4, Glossy Paper, Labels and Embossed are allowed
to select as Paper Type.
10 Main unit control
"Side1/2, XY Ratio Settings" is no more displayed on Paper Settings registration screen
on installation of Fiery because the magnification adjustment cannot be reflected.
on installation of Fiery because the magnification adjustment cannot be reflected.
11 Main unit control
Multi-level print speed setting has been implemented to increase the print speed of
custom size paper. The speed varies depends on the paper size.
custom size paper. The speed varies depends on the paper size.
12 Main unit control
Followings have been changed to improve the registration level:
(1) The timing to perform the registration adjustment
(2) Default value of AG in SIM44-28 to perform the registration adjustment when
necessary.
SIM44-28 AG(RG_PERM_TIMER): Changed from 1 to 0.
*Default value won't change just by upgrading the firmware. Please change the value of
AG in SIM44-28 at the time of firmware upgrade. In addition, execute SIM50-22 if
necessary.
(1) The timing to perform the registration adjustment
(2) Default value of AG in SIM44-28 to perform the registration adjustment when
necessary.
SIM44-28 AG(RG_PERM_TIMER): Changed from 1 to 0.
*Default value won't change just by upgrading the firmware. Please change the value of
AG in SIM44-28 at the time of firmware upgrade. In addition, execute SIM50-22 if
necessary.
Display
