DOWNLOAD Sharp MX-6500N / MX-7500N (serv.man10) Service Manual ↓ Size: 46.6 MB | Pages: 127 in PDF or view online for FREE

MX-7500N  MX-CF11 (INSERTER)  16 – 5

7) Attach the base cover. (1 screw (Packed items No. 3))

8) Attach the front door to the front inner cover, and attach the L-

hinge pins (Packed items No. 12).
MEMO: Insert the L-hinge pin in the lower section into the back

of the Black Mylar.

9) Attach the front inner cover to the tray unit. (2 screws)

10) Attach  the  accessory cover   (Packed  items No. 1) with the

screw (Packed items No. 17) and the winding bushing (Packed

items No. 21).

1) Connect the connector to the decurler unit.

Base cover

MX-7500N  MX-CF11 (INSERTER)  16 – 6

MEMO:  When the  adjuster  bolt is  turned  counterclockwise,  the

height  is  decreased. When  turned  clockwise,  the height is

increased.
NOTE: The specification of the height and the tilt adjustment are as

follows.
Height: The difference of level between top surface of the adjacent

device is within +/-2mm.
Tilt: The difference of clearance between upper and lower part of

the adjacent device is within +/-2mm.

1) Place an adjustment dish under every adjuster bolt, and screw

the bolt. (4 positions)

2) Turn  the adju ster  bolts  (1) and (2)   in  the above   figure,  and

adjust the height.

3) Turn  the adju ster  bolts  (3) and (4)   in  the above   figure,  and

adjust the tilt.

MX-7500N  MX-ST10/CA10 (HIGH CAPACITY STACKER/PAPER CART)  17 – 1

MX-7500N

Service Manual

 

1) Remove the L-Plate.

2) Remove the Locking Plate.

* For European countries, there are three types of Power cords.  

1)

Always work on this unloading in a foursome.

2)

Lay your hands on the palette as shown in the photos below.

NOTE: Try not to lay your hands on the adjuster volts.

NOTE: Before installation, be sure to turn both the operation and
main  power switches off and disconnect the power plug from the
power outlet. Make double sure that the data lamp on the operation
panel does not light up or blink when per- forming installation. 
NOTE: Necessary works before moving the machine.
-  Remove the paper cart from the stacker  before moving.
-  Fix the locking plate which were removed at  B-2) Remove the
Locking Plate.

1)

Attach the guide plate. 

Tighten the paper guide C (Packed item No. 13 with MX-
RB15) at the paper feed entry with screws (Packed item No. 1
with the decurler). 

1

Handle

1

2

Stacker tray

1

3

Frame cart

1

4

Guide plate

1

5

Bracket

1

6

Earth plate

1

7

Paper holder

1

8

Adjuster support

4

9

Sems screw (M5 x 10)

2

10

Hexagonal screw (M3 x 6)

2

11

Bind screw (M4 x 8)

6

12 *

Power cord

1

13

Spacer molt

1

14

Guide mylar

1

15

Label

1

16

Connection Plate

1

Inside the front door

16

Right Side

MX-7500N  MX-ST10/CA10 (HIGH CAPACITY STACKER/PAPER CART)  17 – 2

Attach the guide plate (Packed item No. 4) to the same posi-
tion as above with the screws (Packed item No. 10 x2).

a) Remove the screw. 

b) Attach the black Mylar.   

Attach the black mylar sheet to the paper guide along the ref-
erence line. For the reference, see the figure below.  

c) Fix the guide plate with the black mylar to the paper feed
part of the stacker with the screw (Packed items No.10 Hexag-
onal screw M3x6).  

1)

Tighten the earth plate (Packed item No.6) with screws
(Packed item No.11 x2). 
When connected to MX-RB15 
Insert the screw into the lower hole and tighten it. 

When connected to MX-CF11 or MX-ST10 (linkage of two)
Insert the screw into the upper hole and tighten it. 

1)

Tighten the bracket (Packed item No. 5) to the connection
option with the screws (Packed item No. 11 x4). 

TopPage

: ‘13/Nov