DOWNLOAD Sharp MX-6240N / MX-7040N (serv.man91) Service Manual ↓ Size: 34.26 KB | Pages: 3 in PDF or view online for FREE

 

Sharp Electronics (UK) Ltd., Technical Services Group

 

CCE-1471 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
1. Model Name: 

MX-FR36U (Option for MX-6240N/7040N) 

 
2. Description: 

Upgrade of ICUM, and ICU1-ROM 

 

From May 2015 production 

ROM control No. 

ICUM 

ICU1 

ICU2 

E00 

0510Sc00 

0510Sc00 

0102Sc00 

  Item of change: See the attached sheets. 

 Note) This report is a T/R for the data security kit option, corresponding to general 
       T/R No. CCE-1470 

 
 
 

 

 

ROM Version History Table 

 

No. 

ROM control No. 

ICUM 

ICU1 

ICU2 

Action 

T/R No. 

(3) 

D00 

0410Sc00 

0410Sc00 

0102Sc00 

2014/2 

CCE-1271 

(2) 

C00 

0310Sc00 

0310Sc00 

0102Sc00 

2013/9 

CCE-1190 

(1) 

B00 

0210Sc00 

0210Sc00 

0101Sc00 

2013/1 

CCE-1110R 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

TECHNICAL BULLETIN 

 

Sharp Electronics (UK) Ltd., Technical Services Group

 

CCE-1471 

[Description] 

No. 

Item 

Details 

1 

Main unit control 

Modification of L8-20 which may occur when condition signalling between internal modules is 
not done properly. 

2 

Main unit control 

Modification of a failure to complete Fax firmware upgrade during firmware upgrade 

3 

Main unit control 

Modification of a failure to restart the unit properly while acquiring the image (snapshot) during 
the firmware upgrade due to lack of some data necessary. 

4 

Main unit control 

Modification of the problem that the colour changes before and after the halftone process 
control if the correction amount of halftone process control largely changes from the previous 
value. 

5 

Main unit control 

Modification of Scan job which keep remaining internally. The problem occurs if Eco scan 
setting was enabled but cancelled after previewing for Copy job. 

6 

Main unit control 

Modification of the problems that FAX receiving may stop after reaching to the pre-set limit or 
the job may disappear when printing because the internal processing at the time of job 
completion cannot work correctly. 

7 

Main unit control 

Correction of the problem that the trimmer function of Copy mode becomes unavailable when 
using the account application. 

8 

Main unit control 

Correction of slower performance during batch printing while MFP is in vendor mode. 

9 

Main unit control 

Modification of a problem which occurs with following steps: 1) Print out a test pattern in Paper 
Settings from Bypass tray in duplex. 2) The Bypass tray gets empty 3) Add papers to the 
bypass tray. 4) The test pattern is printed in simplex. 

10  UI 

Modification of a failure to delete the job completed from Job Status (Direct print from USB flash 
drive). User cannot delete the job on the Job Status screen. 

11  UI 

Modification of a problem with "Automatically print stored jobs after login" in User Control which 
is disabled while external authentication for OSA is enabled. 

12  Network 

Factory default of LPD timeout period is changed from 0 (infinite) to 90 sec. 
*The value above will not be changed when updating the firmware in the field. 

13  Network 

Modification of machine lockup (ex. operation panel does not function) due to the unauthorized 
memory access caused by defective internal management processing in WSD module. 

14  Network 

The modification of garbled images which appear while the data communication speed of a 
device is 10 Mbps. 

15  Network 

Modification of a communication error which occurs in case the devices with different MAC 
address share same IP address (i.e. load balancer is installed). 

16  Network 

Modification of different Fax event notification between OSA4.5 and OSA4.1 

17  Network 

Correction of the problem that the machine locks up when accessing the specific MIB with the 
undefined INDEX.  

18  Network 

Modification of an error to authenticate IEEE802.1X for wired LAN 

19  Network 

Modification of network lockup which occurs during the port scan on tandem port. 

20  Network 

Enabling display of Machine ID information in MIB 

21  Network 

Modification is made so that prompt authentication by a login user is enabled/disabled in Soft 
SW. 
 
SIM55-3 SW No.24 Data3 
0: Enabled (Default for all destinations other than Europe) 
1: Disabled 

22  Printer 

Modification of print operation which may stop displaying "Rendering" during mass printing.

 

23  Printer 

Correction of the problem that the machine may lock up when printing the data including the 
specific font with PCL6. 

24  Printer 

Correction of the problem that the performance may be slowing down in the process of 
continuous printing. 

25  Printer 

Setup of the print port for Web Page 

26  Printer 

Correction of the problem that the performance becomes worse or the print job is completed 
without printing all data when printing with PS in some cases. 

 

 

Sharp Electronics (UK) Ltd., Technical Services Group

 

CCE-1471 

 

No. 

Item 

Details 

27  Printer 

Correction of the trouble that the image data is occasionally not printed out when using PCL6 
driver. 

28  Printer 

Correction of the problem that the data may be printed in solid black if the processing of CMYK 
8bit expansion and the processing of halftone process control are performed simultaneously. 

29  Printer 

Modification of machine lock up/ printing failure which occurs while printing particular PS file. 

30  Printer 

Modification of problem with printing smooth transition of gradation in light grey 
The problem occurs while printing InDesign data from MacOS10.6.8. 

31  Printer 

Modification of printing objects with different colour which occurs while printing from AS400. 

32  Image Send 

Correction of PPD2_PRI jam which occurred under following conditions: 
- Fax Soft SW (SW38-8) was set to "Do not output error page in case of fax data reception 
error". 
- Communication error occurred while receiving Fax image data. 
- The device was printing data. 

33  Image Send 

34  Image Send 

If multiple number of received Fax data are manually transferred from Preview screen in a 
batch, sometimes the data output fails. This problem has been corrected. 

35  Image Send 

Modification of the problem that Sender cannot be OFF even though it is OFF on PC-FAX 
driver. 

36  OSA 

Modification of an error to activate Fax OSA application after recovering from power save mode