DOWNLOAD Sharp MX-6201N / MX-7001N (serv.man39) Service Manual ↓ Size: 8.88 MB | Pages: 26 in PDF or view online for FREE

Model
MX-6201N MX-7001N (serv.man39)
Pages
26
Size
8.88 MB
Type
PDF
Document
Service Manual
Brand
Device
Copying Equipment / FUSING SECTION
File
mx-6201n-mx-7001n-sm39.pdf
Date
PREV: Sharp MX-6201N / MX-7001N (serv.man38) Service Manual

Sharp MX-6201N / MX-7001N (serv.man39) Service Manual ▷ View online

MX-7001N  FUSING SECTION  O – 17
l. Transport roller 9 (Drive)
1)
Remove the fusing unit.  (Refer to the "(1) Fusing unit".)
2)
Remove the screw (A), and remove the cover (B). Disconnect
the connector (C). Remove the screws (D), and remove the
cover R (E).
3)
Remove the screws (F), and remove the cover F (G).
4)
Disconnect the connector (H). Remove the screw (I), and
remove the sensor unit (J).
5)
Remove the E-ring (K). Lift the actuator (L), and remove the
gear (M) and the bearing (N).
6)
Remove the screw (O), and remove the earth plate (P).
Remove the E-ring (Q), and remove the bearing (R). Remove
the transport roller 9 (Drive) (S).
Unit
Parts
Mainte
nance
1
Fusing unit
C
Transport roller 9 (Drive)
✕ {
C
1-
A
B
C
D
E
D
F
F
G
I
H
J
L
N
M
K
S
1-C
O
P
Q
R
MX-7001N  FUSING SECTION  O – 18
m. Upper separation pawl, Upper separation pawl SP
1)
Remove the fusing unit. (Refer to the "(1) FUSING UNIT".)
2)
Remove the screws (A). Rotate the fusing web unit (B), and
remove it.
* When installing, engage the fusing web unit (B) to the pawls
(C) of the upper cover.
* When installing, be careful to prevent bending the electrode
(D), and check that the electrode is contacted.
3)
Remove the screws (E), and remove the separation pawl hold-
ers (F). Disengage the upper separation pawls (G), and
remove the upper separation pawl SPs (H).
n. Separation pawl solenoid, Lower separation pawl, Lower
separation pawl SP
1)
Remove the fusing unit. (Refer to the "(1) FUSING UNIT".)
2)
Remove the screw (A), and remove the cover (B). Disconnect
the connector (C). Remove the screws (D), and remove the
cover R (E).
Unit
Parts
Mainte
nance
1
Fusing unit
D
Upper separation pawl
✕ ▲
E
Upper separation pawl SP
✕ ▲
1-D
1-E
A
A
B
B
C
D
Unit
Parts
Mainte
nance
1
Fusing unit
F
Separation pawl solenoid
–
G
Lower separation pawl
✕ ▲
H
Lower separation pawl SP
✕ ▲
E
H
1-E
1-E
1-D
E
E
F
F
H
G
1-H
1-G
1-F
A
B
C
D
E
D
MX-7001N  FUSING SECTION  O – 19
3)
Disconnect the connector (F). Remove the screws (G), and
remove the separation pawl solenoid (H).
4)
Remove the screws (I), and remove the cover F (J).
5)
Remove the screws (K), and remove the lower cover (L).
6)
Open the paper guide (M). Remove the springs (N).
7)
Remove the screw (O), and remove the mounting plate (P).
Remove the paper guide (Q).
8)
Remove the spring (R). Remove the screw (S), and remove
the mounting plate (T) and separation shaft (U).
9)
Remove the lower separation pawl units (V). Disengage the
lower separation pawl SPs (X) from the lower separation pawls
(W).
1-F
F
H
G
I
I
J
K
K
L
K
M
N
Q
P
O
S
T
U
R
X
1-G
W
1-H
V
MX-7001N  FUSING SECTION  O – 20
o. Web unit
1)
Remove the fusing unit.  (Refer to the "(1) Fusing unit".)
2)
Remove the screws (A). Rotate the fusing web unit (B), and
remove it.
* When installing, engage the fusing web unit (B) to the pawls
(C) of the upper cover.
* When installing, be careful to prevent bending the electrode
(D), and check that the electrode is contacted.
3)
Remove the screw (E), and remove the bearing (F).
4)
Remove the wind-up side (G) of web unit. Remove the collar
(H).
5)
Remove the springs (I) and the bearings (J). Remove the roller
(K).
6)
Pull out the shafts (L) from rear side.
* When installing, be careful to the installing direction of the
shafts. First of all, insert the side where the tip of the shaft
each is steps.
Unit
Parts
Mainte
nance
1
Fusing unit
I
Web unit
✕ ▲
1-I
A
A
B
B
C
D
E
F
G
H
K
I
J
J
I
L
L
Page of 26
Display

Click on the first or last page to see other MX-6201N / MX-7001N (serv.man39) service manuals if exist.

RANDOM: