DOWNLOAD Sharp MX-5500N / MX-6200N / MX-7000N (serv.man72) Service Manual ↓ Size: 5.46 MB | Pages: 20 in PDF or view online for FREE

Model
MX-5500N MX-6200N MX-7000N (serv.man72)
Pages
20
Size
5.46 MB
Type
PDF
Document
Service Manual
Brand
Device
Copying Equipment / Installation Manual-Main Unit
File
mx-5500n-mx-6200n-mx-7000n-sm72.pdf
Date

Sharp MX-5500N / MX-6200N / MX-7000N (serv.man72) Service Manual ▷ View online

MX-7000N  MX-5500N/6200N/7000N  1 – 16
5)
Remove the rear end regulation plate F and R, and remove the
screw.
6)
Install the rear end regulation plate F and R, and fix with the
screw.
7)
Remove the screw, and remove the mylar sheet. Change the
installing direction and install with screws. (2 positions)
8)
Open the waste toner bottle section cover.
9)
Remove the B5 size regulation plate.
10) Install the B5 size regulation plate to the tray 1.
11) Attach the A4 size regulation plate to inner side of the waste
toner bottle section cover.
1
1
2
2
3
3
MX-7000N  MX-5500N/6200N/7000N  1 – 17
12) Close the waste toner bottle section cover.
13) Close the tandem cassette.
c. Tray 3, tray4
1)
Pull out gently the tray 3/4 until it stops.
If paper remains in the tray, remove it.
2)
Adjust the guide plates A and B by squeezing their lock levers
and sliding them to match the vertical and horizontal dimen-
sions of the paper to be loaded.
The guide plates A and B are slidable. Slide each guide plate
while squeezing its lock lever.
L. Specifications setup
Used to set the specifications with SIM26 according to the cus-
tomer's request.
To customize the following items after completion of the destination
setup, change the set values.
M. Image quality check
Be sure to check the following items related to image quality. For
details of the adjustment and checking procedures, refer to the “[6]
ADJUSTMENT” on the Service Manual.
Check that the following items are normal. If not, carry out the
adjustment.
NOTE: When installing the copier, be sure to carry out the copy
color balance and the printer color balance.
1)
Image skew (see ADJ 8)
2)
Image resist (see ADJ 12)
3)
Image loss, void area (see ADJ 20)
4)
Copy color balance (Auto adjustment)
5)
Printer color balance (Auto adjustment)
(1) Copy color balance adjustment (Auto adjustment)
a. Note before execution of the copy color balance adjust-
ment (Auto adjustment)
• Be sure to use the specified paper for color.
b. Adjustment procedure
1)
Enter the SIM 46-24 mode.
2)
Press [EXECUTE] key. (A3 or 11" x 17" paper is automatically
selected.)
The color patch image (adjustment pattern) is printed out.
A
B
SIM No
Content
26
6
Used to set the destination.
SIM No
Content
26
2
Paper size setting of the Tray1/LCC.
3
Used to set the auditor specification mode.
5
Used to set the number (1 or 2) of count of paper 
(A3 or WLT or 8K) that passes.
1:1pc 2:2pcs
* Targets: Total counter, maintenance counter, 
developer counter.
18
Used to set YES/NO of the toner save mode (Only 
in UK and Japan versions)
* Carry out the setting by the user's program 
except the UK version.
1:accept 2:inhibit
52
Used to set whether non-printed paper (insertion 
paper, cover paper) is counted up or not.
1:YES 2:NO
53
Used to set YES/NO of auto color calibration 
permission.
1:accept 2:inhibit
65
Used to set the limit number of sheets for stapling.
1:limited 2:unlimited
SIMULATION NO.46-24
TEST
ENGINE HALFTONE AUTO ADJUSTMENT
EXECUTE
CLOSE
PRESS [EXECUTE] TO PROCON EXECUTIONAND PRINT THE TEST PATCH.
(PLEASE USE SPECIFIED TYPE OF A3 OR 11"
17" SIZE PAPER
FOR THIS ADJUSTMENT)
MX-7000N  MX-5500N/6200N/7000N  1 – 18
3)
Set the color patch image (adjustment pattern) paper printed in
procedure 2) on the document table.
Place the printed color patch image (adjustment pattern) paper
so that the thin lines on the paper are on the left side. At this
time, place 5 sheets of white paper on the printed color patch
image (adjustment pattern) paper.
4)
Press [FACTORY] key, and press [EXECUTE] key.
The copy color balance adjustment is automatically executed
and prints the color balance check patch image.
5)
Press [OK] key.
Note:
Do not cancel the simulation until "PLEASE QUIT THIS
MODE" is displayed.
6)
Check the color balance and density.
Check to insure that the printed color balance check patch
image is within the following specifications.
The print density must be changed gradually from the lighter
level to the darker level. The density changing direction must
not be reversed.
The density level of each color must be almost at the same
level.
Patch B may not be copied.
Patch A must not be copied.
(2) Printer color balance adjustment 
(Auto adjustment)
a. Note for execution of the color balance adjustment (Auto
adjustment)
• The copy color balance adjustment must have been completed
properly.
• Be sure to use the specified paper for color.
b. Adjustment procedure
1)
Enter the SIM 67-24 mode.
2)
Press [EXECUTE] key. (A3 or 11" x 17" paper is automatically
selected.)
The color patch image (adjustment pattern) is printed out.
SIMULATION NO.46-24
TEST
ENGINE HALFTONE AUTO ADJUSTMENT
PLEASE SELECT THE MODE (FACTORY) OR (SERVICE) AND PLACE
THE PRINTED TEST PATCH ON DOCUMENT GLASS THEN PRESS [EXECUTE].
*LIGHT AREA AT LEFT SIDE ON DOCUMENT GLASS.
,
SERVICE
FACTORY
EXECUTE
CLOSE
SIMULATION NO. 46-24
TEST
ENGINE HALFTONE AUTO ADJUSTMENT
OK
CONFIRM THE ADJUSTED PATCH AND PRESS [OK] TO REGISTER THIS PATCH DATA
,PRESS [REPEAT] TO CONTINUE THIS PROCEDURE.
REPEAT
CLOSE
SIMULATION NO. 46-24
TEST
ENGINE HALFTONE AUTO ADJUSTMENT
CLOSE
COMPLETED THIS PROCEDURE.
PLEASE QUIT THIS MODE.
C
Y
High density
Low density
Fig. 1 PG image
Max
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
M
Bk
1) The max. density
section is not blurred.
3) Patch for each of C, M, Y, BK
The patch density is identical between patches or not reversed.
The patch density is changed gradually.
2) Patch C or D of each of Y, C, M,
and BK is very slightly copied.
Patch A of each of Y, M,
C, and BK are not copied.
SIMULATION NO.67-24
TEST
PRINTER ENGINE HALFTONE AUTO ADJUSTMENT MODE
EXECUTE
CLOSE
PRESS [EXECUTE] TO PROCON EXECUTION AND PRINT THE TEST PATCH.
(PLEASE USE SPECIFIED TYPE OF A3 OR 11" 17" SIZE PAPER
FOR THIS ADJUSTMENT)
MX-7000N  MX-5500N/6200N/7000N  1 – 19
3)
Set the color patch image (adjustment pattern) paper printed
on the document table.
Place the printed color patch image (adjustment pattern) paper
so that the thin lines on the paper are on the left side. At this
time, place 5 sheets of white paper on the printed color patch
image (adjustment pattern) paper.
4)
Press [FACTORY] key, and press [EXECUTE] key.
The copy color balance adjustment is automatically executed
and prints the color balance check patch image. Wait until the
operation panel shown in the next procedure is displayed.
5)
Press [OK] key.
NOTE:
Do not cancel the simulation until "PLEASE QUIT THIS
MODE" is displayed.
6)
Check the color balance and density.
Check to insure that the printed color balance check patch
image is within the following specifications.
The print density must be changed gradually from the lighter
level to the darker level. The density changing direction must
not be reversed.
The density level of each color must be almost at the same
level.
Patch B may not be copied.
Patch A must not be copied.
N. Function and operation check
Check that the following operations are normal.
O. Setup and adjustment data recording
Print the various setup data and the adjustment data (list) with
SIM22-6 and keep the data.
• In case of a memory trouble, if the data are not kept, all the
adjustments must be made again.
• If the data are kept, the setup values and the adjustment values
can be entered without adjustments, shortening the servicing
time.
PRINTER CALIBRATION
SIMULATION NO.67-24
TEST
PRINTER ENGINE HALFTONE AUTO ADJUSTMENT MODE
PLEASE SELECT THE MODE (FACTORY) OR (SERVICE) AND PLACE
THE PRINTED TEST PATCH ON DOCUMENT GLASS THEN PRESS [EXECUTE].
*LIGHT AREA AT LEFT SIDE ON DOCUMENT GLASS.
,
SERVICE
FACTORY
EXECUTE
CLOSE
CLOSE
SIMULATION NO.67-24
TEST
PRINTER ENGINE HALFTONE AUTO ADJUSTMENT MODE
OK
CONFIRM THE ADJUSTED PATCH AND PRESS [OK] TO REGISTER THIS PATCH DATA
PRESS [REPEAT] TO CONTINUE THIS PROCEDURE.
REPEAT
SIMULATION NO.67-24
TEST
PRINTER ENGINE HALFTONE AUTO ADJUSTMENT MODE
CLOSE
COMPLETED THIS PROCEDURE.
PLEASE QUIT THIS MODE.
Check item list
Equipped condition
Key-in (operation panel)
Display (operation panel)
Paper feed 
operation
Hand feed
Paper tray
Paper size detection
Originals size 
detection
Original table 
mode
DSPF mode
DSPF 
operation/
duplex 
operation
S-S mode
D-S mode
S-D mode
D-D mode
Bookbinding operation
When the finisher is installed
Stapling operation
When the finisher is installed
Grouping operation
When the finisher is installed
Sorting operation
When the finisher is installed
High density
Low density
Fig. 1 PG image
Max
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
C
M
Y
Bk
1) Max. density section
is not blurred.
3) Patch for each of C, M, Y, BK
The patch density is identical between patches or not reversed.
The patch density is changed gradually.
2) Patch C or D of each of Y, C,
M, Bk is very slightly copied.
Patch A of Y, M, C, and
BK are not copied.
PRINTER CALIBRATION
Page of 20
Display

Click on the first or last page to see other MX-5500N / MX-6200N / MX-7000N (serv.man72) service manuals if exist.