Sharp MX-5500N / MX-6200N / MX-7000N (serv.man66) Service Manual ▷ View online
MX-7000N FUSING SECTION O – 17
2)
Remove the screw (A), and remove the cover (B). Disconnect
the connector (C). Remove the screws (D), and remove the
cover R (E).
the connector (C). Remove the screws (D), and remove the
cover R (E).
3)
Remove the screws (F), and remove the cover F (G).
4)
Disconnect the connector (H). Remove the screw (I), and
remove the sensor unit (J).
remove the sensor unit (J).
5)
Remove the E-ring (K). Lift the actuator (L), and remove the
gear (M) and the bearing (N).
gear (M) and the bearing (N).
6)
Remove the screw (O), and remove the earth plate (P).
Remove the E-ring (Q), and remove the bearing (R). Remove
the transport roller 9 (Drive) (S).
Remove the E-ring (Q), and remove the bearing (R). Remove
the transport roller 9 (Drive) (S).
m. Upper separation pawl, Upper separation pawl SP
1)
Remove the fusing unit. (Refer to the "(1) FUSING UNIT".)
2)
Remove the screws (A). Rotate the fusing web unit (B), and
remove it.
* When installing, engage the fusing web unit (B) to the pawls
remove it.
* When installing, engage the fusing web unit (B) to the pawls
(C) of the upper cover.
* When installing, be careful to prevent bending the electrode
(D), and check that the electrode is contacted.
A
B
C
D
E
D
F
F
G
I
H
J
L
N
M
K
Unit
Parts
Mainte
nance
1
Fusing unit
C
Upper separation pawl
✕
▲
D
Upper separation pawl SP
✕
▲
S
1-B
O
P
Q
R
1-C
1-D
A
A
B
B
C
D
MX-7000N FUSING SECTION O – 18
3)
Remove the screws (E), and remove the separation pawl hold-
ers (F). Disengage the upper separation pawls (G), and
remove the upper separation pawl SPs (H).
ers (F). Disengage the upper separation pawls (G), and
remove the upper separation pawl SPs (H).
n. Lower separation pawl, Lower separation pawl SP
1)
Remove the fusing unit. (Refer to the "(1) FUSING UNIT".)
2)
Remove the screw (A), and remove the cover (B). Disconnect
the connector (C). Remove the screws (D), and remove the
cover R (E).
the connector (C). Remove the screws (D), and remove the
cover R (E).
3)
Remove the screws (F), and remove the cover F (G).
4)
Remove the screws (H), and remove the lower cover (I).
5)
Open the paper guide (J). Remove the springs (K).
6)
Remove the screw (L), and remove the mounting plate (M).
Remove the paper guide (N).
Remove the paper guide (N).
Unit
Parts
Mainte
nance
1
Fusing unit
E
Lower separation pawl
✕
▲
F
Lower separation pawl SP
✕
▲
E
H
1-D
1-D
1-C
E
E
F
F
H
G
1-F
1-E
A
B
C
D
E
D
F
F
G
H
H
I
H
J
K
N
M
L
MX-7000N FUSING SECTION O – 19
7)
Remove the lower separation pawl units (O). Disengage the
lower separation pawl SPs (Q) from the lower separation
pawls (P).
lower separation pawl SPs (Q) from the lower separation
pawls (P).
o. Web unit
1)
Remove the fusing unit. (Refer to the "(1) Fusing unit".)
2)
Remove the screws (A). Rotate the fusing web unit (B), and
remove it.
* When installing, engage the fusing web unit (B) to the pawls
remove it.
* When installing, engage the fusing web unit (B) to the pawls
(C) of the upper cover.
* When installing, be careful to prevent bending the electrode
(D), and check that the electrode is contacted.
3)
Remove the screw (E), and remove the bearing (F).
4)
Remove the wind-up side (G) of web unit. Remove the collar
(H).
(H).
5)
Remove the springs (I) and the bearings (J). Remove the roller
(K).
(K).
6)
Pull out the shafts (L) from rear side.
* When installing, be careful to the installing direction of the
* When installing, be careful to the installing direction of the
shafts. First of all, insert the side where the tip of the shaft
each is steps.
each is steps.
Unit
Parts
Mainte
nance
1
Fusing unit
G
Web unit
✕
▲
Q
1-F
P
1-E
O
1-G
A
A
B
B
C
D
E
F
G
H
I
J
K
J
I
L
L
MX-7000N FUSING SECTION O – 20
7)
Remove the web unit (M). Remove the collar (N) and the break
rubber (O).
* When installing the collar (N) and the break rubber (O), pre-
rubber (O).
* When installing the collar (N) and the break rubber (O), pre-
vent damage of the web unit (M), install to other side of red
line (P).
line (P).
* When installing, hang the web unit to the shafts (Q) and the
roller (R), and arrange as shown below.
B. Others
(1) Fusing cooling fan
1)
Remove the rear cabinet. (Refer to the "[A] EXTERNAL OUT-
FIT".)
FIT".)
2)
Remove the screws (A), and open the control box (B).
3)
Remove the snap bands (C). Remove the harness (E) from the
wire saddles (D).
wire saddles (D).
Parts
Page
a
Fusing cooling fan
O -20
b
Fusing motor
O -21
c
External variable motor
O -21
d
Fusing web cleaning motor
O -22
e
Fusing air outlet fan
O -23
M
1-G
N
O
P
Q
A
Q
R
b
e
d
a
c
Parts
a
Fusing cooling fan
a
B
B
A
A
D
C
C
D
E
Click on the first or last page to see other MX-5500N / MX-6200N / MX-7000N (serv.man66) service manuals if exist.