Sharp MX-5500N / MX-6200N / MX-7000N (serv.man64) Service Manual ▷ View online
MX-7000N TRANSFER SECTION M – 13
* When installing, be careful to prevent damage of the primary
transfer belt where right side (K) of the PTC unit is a cause.
* When installing, check that rails (L) is engaged.
a. PTC cleaner B, PTC cleaner
1)
Remove the paper dust removal cleaner. (Refer to the “[G]
PAPER TRANSPORT SECTION”.)
PAPER TRANSPORT SECTION”.)
2)
Remove the PTC unit. (Refer to the "(1) PTC unit".)
3)
After disengaging the pawl (A), disengage the pawl (B).
Remove the holder cover (C).
Remove the holder cover (C).
4)
Disenage the pawl (D). Remove the PTC cleaner B (E), and
remove the PTC cleaner (F).
* When installing, check that the charger wire (G) is posi-
remove the PTC cleaner (F).
* When installing, check that the charger wire (G) is posi-
tioned to center of the cleaner pad (H).
* When installing the PTC cleaner B (E), be sure to check that
the pawl (D) and the pawl (I) of the PTC cleaner (F) is
engaged.
engaged.
* When removing or installing, be careful that the charger wire
(G) hang up the lower side (J) of the PTC cleaner (F).
b. Charger wire
1)
Remove the paper dust removal cleaner. (Refer to the “[G]
PAPER TRANSPORT SECTION”.)
PAPER TRANSPORT SECTION”.)
2)
Remove the PTC unit. (Refer to the "(1) PTC unit".)
3)
Remove the PTC cleaner B and PTC cleaner. (Refer to the “a.
PTC cleaner B, PTC cleaner”.)
PTC cleaner B, PTC cleaner”.)
Unit
Parts
Mainte
nance
1
PTC unit
a
PTC cleaner B
▲
b
PTC cleaner
▲
K
L
L
1-b
1-a
A
B
C
Unit
Parts
Mainte
nance
1
PTC unit
c
Charger wire
✕
▲
G
H
J
D
E
I
1-b
F
1-a
1-c
MX-7000N TRANSFER SECTION M – 14
4)
Remove the spring (B) from the pawl (A). Remove the round
terminal (D) from the pawl (C). Remove the charger wire (E).
Remove the spring (B) form the round terminal (F).
* When installing, hold the round terminal (D). Don't touch the
terminal (D) from the pawl (C). Remove the charger wire (E).
Remove the spring (B) form the round terminal (F).
* When installing, hold the round terminal (D). Don't touch the
wire directly.
* When installing, be careful to dirt of the wire and don't put oil
etc., and be sure to prevent the wire bending or twisting.
D. Secondary transfer separating drive unit
(1) Secondary transfer separating drive unit
1)
Release the lock (A), and open the right door unit (B).
2)
Remove the screws (C), and remove the paper guide (D).
3)
Remove the screws (E), and remove the pressure plate (F)
and springs (G).
and springs (G).
4)
Disconnect the connector (H). Remove the screw (I). Disenage
the pawl (J), and remove the cover (K).
the pawl (J), and remove the cover (K).
5)
Remove the screws (L), and remove the secondary transfer
separation drive unit (M).
separation drive unit (M).
Unit
Parts
Page
1
PTC unit
a
Secondary transfer
separation motor
separation motor
M -15
b
Secondary transfer
separation drive sensor
separation drive sensor
M -15
Parts
1
Secondary transfer drive unit
A
B
C
D
B
F
E
1-c
1
1-a
1-b
A
B
C
C
D
E
E
E
E
F
G
G
I
H
H
K
J
L
L
M
1
MX-7000N TRANSFER SECTION M – 15
a. Secondary transfer separation motor
1)
Release the lock (A), and open the right door unit (B).
2)
Remove the screws (C), and remove the paper guide (D).
3)
Remove the screws (E), and remove the pressure plate (F)
and springs (G).
and springs (G).
4)
Disconnect the connector (H). Remove the screws (I), and
remove the secondary transfer separation motor unit (J).
remove the secondary transfer separation motor unit (J).
5)
Disengage the pawls (K), and remove the coupling (M) and
spring (N) from the secondary transfer separation motor (L).
spring (N) from the secondary transfer separation motor (L).
b. Secondary tansfer separation drive sensor
1)
Release the lock (A), and open the right door unit (B).
Unit
Parts
1
Secondary transfer
separating drive unit
separating drive unit
a
Secondary transfer separation motor
1-a
A
B
C
C
D
E
E
E
E
F
G
G
Unit
Parts
1
Secondary transfer
separating drive unit
separating drive unit
b
Secondary transfer separation drive
sensor
sensor
I
H
I
J
K
M
K
N
L
1-a
1-b
A
B
MX-7000N TRANSFER SECTION M – 16
2)
Remove the screws (C), and remove the paper guide (D).
3)
Remove the screws (E), and remove the pressure plate (F)
and springs (G).
and springs (G).
4)
Disconnect the connector (H). Remove the screw (I). Disenage
the pawl (J), and remove the cover (K).
the pawl (J), and remove the cover (K).
5)
Disconnect the connector (L), and remove the secondary sep-
aration drive sensor (M).
aration drive sensor (M).
E. Others
(1) Transfer belt separation BK detection
1)
Remove the primary transfer unit. (Refer to the "A. Primary
transfer unit".)
transfer unit".)
2)
Remove the rear cabinet. (Refer to the "[A] EXTERNAL OUT-
FIT")
FIT")
3)
Remove the screws (A), and open the control box (B).
C
C
D
E
E
E
E
F
G
G
I
H
H
K
J
L
M
1-b
Parts
Page
a
Transfer belt separation BK detection
M -16
b
Sensor inside the PTC unit
M-17
Parts
a
Transfer belt separation BK detection
b
a
a
B
B
A
A
Click on the first or last page to see other MX-5500N / MX-6200N / MX-7000N (serv.man64) service manuals if exist.