Sharp MX-5500N / MX-6200N / MX-7000N (serv.man60) Service Manual ▷ View online
MX-7000N LSU SECTION i – 6
3)
Remove the screws (A), and remove the earth wire (B).
Remove the cover (C).
* When installing the cover (C), engage the pawls (D) to cover
Remove the cover (C).
* When installing the cover (C), engage the pawls (D) to cover
lower (E). At this time be careful it bite the wire.
4)
Remove the screws (F), and remove the cover (G).
* When removing the cover (G), be careful to work place and
* When removing the cover (G), be careful to work place and
method, to don't enter the dust into the unit. Trouble (image
not fully etc.) may occur.
not fully etc.) may occur.
* When installing the cover, lock the pawl (H).
5)
Disconnect the connector (I), and remove the screws (J), and
remove the polygon motor (K). Disconnect the connector (L).
* When disassembling, be careful to drop the screw (etc.)
remove the polygon motor (K). Disconnect the connector (L).
* When disassembling, be careful to drop the screw (etc.)
inside the LSU.
* Don't touch the cover glass surface (M) of polygon motor.
6)
Loosen the screw (N), and remove the LSU thermistor 2 (O).
Disconnect the connector (P).
* When disassembling, be careful to drop the screw (etc.)
Disconnect the connector (P).
* When disassembling, be careful to drop the screw (etc.)
inside the LSU.
e. LSU thermistor 1
1)
Remove the left cabinet. (Refer to the “[A] EXTERNAL OUT-
FIT”.)
FIT”.)
2)
Remove the LSU. (Refer to the “(1) LSU”.)
3)
Remove the screws (A), and remove the earth wire (B) and
cover (C).
cover (C).
B
C
D
D
E
A
G
F
H
K
I
J
1-d
L
M
Unit
Parts
1
LSU
f
LSU thermistor 1
O
P
N
1-e
1-f
C
A
A
A
B
A
MX-7000N LSU SECTION i – 7
4)
Remove the screw (D), and remove the LSU thermistor 1 (E).
Disconnect the connector (F).
Disconnect the connector (F).
B. Others
(1) LSU shutter solenoid CL
1)
Remove the left cabinet. (Refer to the “[A] EXTERNAL OUT-
FIT”.)
FIT”.)
2)
Remove the LSU. (Refer to the "(1) LSU".)
3)
Disconnect the connector (A), and remove the screw (B), and
remove the LSU shutter solenoid CL unit (C).
* When installing, insert the U-cut part (D) of solenoid arm to
remove the LSU shutter solenoid CL unit (C).
* When installing, insert the U-cut part (D) of solenoid arm to
the shaft (E).
4)
Disconnect the connector (F). Remove the screws (G), and
remove the LSU shutter solenoid CL (H).
* When installing, hook the solenoid pin (I) to the solenoid arm
remove the LSU shutter solenoid CL (H).
* When installing, hook the solenoid pin (I) to the solenoid arm
(J).
(2) LSU shutter solenoid BK
1)
Remove the rear cabinet and rear cabinet lower. (Refer to the
"[A] EXTERNAL OUTFIT".)
"[A] EXTERNAL OUTFIT".)
Parts
Mainte
nance
Page
a
LSU shutter solenoid CL
–
i - 7
b
LSU shutter solenoid BK
–
i - 7
c
Cleaning base
✕
▲
i - 9
Parts
a
LSU shutter solenoid CL
D
E
F
1-f
b
a
c
a
Parts
b
LSU shutter solenoid BK
A
B
C
D
E
F
G
G
H
I
J
a
b
MX-7000N LSU SECTION i – 8
2)
Remove the screws (A), and open the control box (B).
3)
Remove the screws (C), and remove the flywheel (D).
* Check to confirm that has not come in contact with the har-
* Check to confirm that has not come in contact with the har-
ness etc.
4)
Disconnect the connector (E). Remove the screws (F). Disen-
gage the pawl (G), and remove the duct (H).
gage the pawl (G), and remove the duct (H).
5)
Disconnect the connector (I). Remove the screws (J), and
remove the LSU shutter solenoid BK uint (K).
* When installing, engage the shutter drive shaft (L) to the
remove the LSU shutter solenoid BK uint (K).
* When installing, engage the shutter drive shaft (L) to the
solenoid arm (M).
6)
Disconnect the connector (N), and remove the snap band (O).
Remove the screws (P), and remove the mounting plate (Q).
* When installing, engage the spring (R) to the groove (S) of
Remove the screws (P), and remove the mounting plate (Q).
* When installing, engage the spring (R) to the groove (S) of
the mounting plate and the groove (T) of the solenoid arm.
7)
Disengage the pawl (U), and remove the LSU shutter solenoid
BK (V).
BK (V).
B
B
A
A
C
D
C
G
F
H
E
J
K
L
M
I
N
P
P
Q
R
S
T
O
V
U
b
MX-7000N LSU SECTION i – 9
(3) Cleaning base
1)
Open the front cabinet (A).
2)
Remove the cleaning rod (B).
3)
Remove the dirty cleaning base (C).
4)
Open the cover (D), and pull out the cleaning base (E) for
replacement.
replacement.
5)
Attach the new cleaning base (F) to the mounting hole with fit-
ting to the pawl.
ting to the pawl.
Parts
Mainte
nance
c
Cleaning base
✕
▲
c
A
B
C
c
D
E
F
Click on the first or last page to see other MX-5500N / MX-6200N / MX-7000N (serv.man60) service manuals if exist.