DOWNLOAD Sharp MX-5500N / MX-6200N / MX-7000N (serv.man56) Service Manual ↓ Size: 1.81 MB | Pages: 10 in PDF or view online for FREE

MX-7000N  SCANNER SECTION  D – 2

This section functions and operates as follows:
1)

The copy lamp radiates light onto the document, and the con-
trast of the reflected light is scanned by the three line (RGB)
CCD element and converted into image signals (analog).

2)

The image signals (analog) are converted into 10bit digital sig-
nals by the A/D converter.

3)

The image signals (digital) are sent to the image process sec-
tion (scanner control PWB).

The optical section drive power is transmitted from the scanner
motor (MIM) to the drive pulley and the wire through the belt, to
drive the copy lamp unit and the mirror base which are attached by
the drive wires.
The scanner motor (MIM) is controlled by the drive signal sent from
the scanner control PWB.

The scanner lamp (CLI) is driven by the scanner lamp drive voltage
generated in the CL inverter PWB according to the control signal
sent from the scanner control PWB.

The copy lamp radiates light onto the document, and the contrast of
the reflected light is scanned by the three line (RGB) CCD element
and converted into image signals (analog).
Each color component of RGB is separately extracted from the
document image by the three lines (RGB) of the CCD elements.
The red CCD extracts the red components from the document
image, the green CCD the green components, and the blue CCD
the blue components. This operation is called Color Separation.
A CCD element has three CCD elements of RGB.
Scanning of a document in the main scanning direction is per-
formed by the CCD elements. Scanning of a document in the sub
scanning direction is performed by shifting the scanner unit position
with the scanner motor.
Document images are optically reduced by the lens and projected
to the CCD elements.
Scanning resolution is 600 dpi.

(Image data per 1 line)

1)

Each image signal (analog) of RGB is converted into 10bit dig-
ital signal by the A/D converter.
Each color pixel has 10bit information.

2)

Each 10bit digital image signal of RGB is sent to the image
process section. 

Zooming in the sub scanning direction is performed by changing
the scanning speed in the sub scanning direction.
Zooming in the main scanning direction is performed by the image
process technology (software), it is not achieved optically.

R
G
B

Red component of
image data

Blue component of
image data

Freen component of
image data

R

G

B

CCD PWB

B ADC

Transfer IC

B

B

3

CCD

B

IC

G

IC

R

IC

G ADC

R ADC

R

R

G

G

MX-7000N  SCANNER SECTION  D – 3

1)

Remove the upper cabinet rear cover. (Refer to the "[A]
EXTERNAL OUTFIT".)

2)

Remove the DSPF unit. (Refer to the "[C] DSPF SECTION".)

3)

Remove the table glass and the SPF glass. (Refer to the “a.
Table glass, SPF glass”.)

4)

Remove the upper cabinet rear, the upper cabinet left, the
upper cabinet right, the front cabinet upper, and the operation
panel base plate. (Refer to the "[A] EXTERNAL OUTFIT".)

5)

Remove the operation panel unit. (Refer to the "[B] OPERA-
TION PANEL".)

6)

Remove the screw (A), and remove the earth wire (B). Discon-
nect the connectors (C). Remove the snap band (D), the mylar
sheet (E), and remove the harnesses (G) from edge saddles
(F).

1

Scanner unit

a

Table glass

{

D - 4

b

SPF  glass

{

c

Lens

{

D - 5

d

CCD

{

e

Reflector

{

D - 5

f

Mirror

{

g

Scanner lamp

{

h

CL inverter PWB

–

i

CCD unit

–

D - 6

j

Rails

✩

D - 7

k

Drive wire

✕

D - 7

l

Drive belt

✕

m

Scanner motor

–

D - 7

n

Scanner home position 
sensor

–

D - 8

o

Original cover SW

–

D - 8

p

Document detection light 
collector PWB

–

D - 8

q

Document detection light 
emitting PWB

–

D - 9

1

Scanner unit

MX-7000N  SCANNER SECTION  D – 4

7)

Remove the screws (H), and remove the support plate (I). Dis-
connect the connector (J), and remove the snap band (K).

8)

Disconnect the connector (L), and remove the screws (M), and
remove the air outlet duct (N).

9)

Remove the screws (O), and remove the scanner unit (P).

1)

Loosen the screws (A), and lower the angle adjustment plate
(B). 

2)

Open the DSPF unit (C).

1

Scanner unit

a

Table glass

{

b

SPF  glass

{

MX-7000N  SCANNER SECTION  D – 5

3)

Remove the screws (D), and remove the glass holder (E).
Remove the table glass (F). Remove the screws (G), and
remove the SPF glass (H).

1)

Remove the table glass and the SPF glass. (Refer to the "a.
Table glass, SPF glass".)

2)

Remove the screws (A), the earth wire (B), and remove the
dark box (C). Remove the lens cover (D).

3)

Clean the lens (E) and the CCD (F).

1)

Remove the table glass and the SPF glass. (Refer to the "a.
Table glass, SPF glass".)

2)

Clean the reflector (A) and mirror (B).

1

Scanner unit

c

Lens

{

d

CCD

{

1

Scanner unit

e

Reflector

{

f

Mirror

{

g

Scanner lamp

{

h

CL inverter PWB

–