Sharp MX-5500N / MX-6200N / MX-7000N (serv.man46) Service Manual ▷ View online
MX-7000N SIMULATION 7 – 11
2-2
Purpose
Operation test/Check
Function (Purpose) Used to check the operations of the sen-
sors and detectors in the automatic docu-
ment feeder unit and the control circuits.
ment feeder unit and the control circuits.
Section
DSPF
Operation/Procedure
The operating conditions of the sensors and detectors are dis-
played.
Sensors and detectors which are turned on are highlighted.
The operating conditions of the sensors and detectors are dis-
played.
Sensors and detectors which are turned on are highlighted.
NOTE: SWD_LEN and SWD_AD are not ON/OFF display.
2-3
Purpose
Operation test/Check
Function (Purpose) Used to check the operations of the loads
in the automatic document feeder unit and
the control circuits.
the control circuits.
Section
DSPF
Operation/Procedure
1)
1)
Select a target of the operation check with the touch panel.
2)
Press [EXECUTE] key.
The selected load is operated.
When [EXECUTE] is pressed, the operation is stopped.
The selected load is operated.
When [EXECUTE] is pressed, the operation is stopped.
3
3-2
Purpose
Operation test/Check
Function (Purpose) Used to check the operation of sensor and
detector in the finisher and the control cir-
cuits.
cuits.
Section
Finisher
Operation/Procedure
The operating conditions of the sensors and detectors are dis-
played.
Sensors and detectors which are turned on are highlighted.
The operating conditions of the sensors and detectors are dis-
played.
Sensors and detectors which are turned on are highlighted.
<4K finisher>
SSET
DSPF installation detection
SOCD
DSPF open/close detection
SCOV
DSPF cover SW
SLCOV
DSPF lower door open/close detection
SPED1
DSPF document empty detection
SPED2
DSPF document detection
SPPD1
DSPF document pass detection 1
SPPD2
DSPF document pass detection 2
SPPD3
DSPF document pass detection 3
SPPD4
DSPF document pass detection 4
SPPD5
DSPF document pass detection 5
SPOD
DSPF paper exit detection
SPRDMD
DSPF random feed paper size detection
SPLS1
DSPF document length detection short
SPLS2
DSPF document length detection long
STLD
DSPF document tray lower limit detection
STUD
DSPF document tray upper limit detection
STMPU
DSPF stamp unit installation detection
SWD_LEN
DSPF guide plate position
SWD_AD
DSPF document detection volume output
SPUM
DSPF paper feed motor
SPFM
DSPF transport motor
SPOM
DSPF paper exit motor
SLUM
DSPF lift motor
SPFFAN
DSPF fan motor
SPFC
DSPF paper feed clutch
SRRC
DSPF resist roller clutch
SRRBC
DSPF resist roller break clutch
DSPF SENSOR CHECK SWD_LEN : **** SWD_AD : ***
CLOSE
SIMULATION NO.02-02
TEST
1/1
SSET
SOCD
SCOV
SLCOV
SPED1
SPED2
SPPD1
SPPD2
SPPD3
SPPD4
SPPD5
SPOD
SPRDMD
SPLS1
SPLS2
STLD
STUD
STMPU
STRRC
DSPF No. 1 resist roller clutch
STRRBC
DSPF No. 1 resist roller break clutch
STRC
DSPF transport clutch
STMPS
Stamp solenoid (only when installed)
FJPID
Interface transport unit entry port detection
FJPOD
Interface transport unit exit port detection
FJPDD
Interface transport unit cover detection
FED
Entry port paper detection
FAED1
Tray 1 area detection 1
FAED2
Tray 1 area detection 2
FAED3
Tray 1 area detection 3
FFJHPD
Alignment plate HP detection front
FRJHPD
Alignment plate HP detection rear
FBED1
Tray 1 paper detection
FBED2
Tray 2 paper detection
FCCD
Tray approaching detection
FSLD1
Tray 1 paper surface detection
FPDD1
Paper exit detection
FSLD2
Tray 2 paper surface detection
FASHPD
Rear edge assist HP detection
FSWHPD
Oscillation guide HP detection
FSWOPD
Oscillation guide open detection
FSTPD
Staple tray paper detection
FSHPD
Staple drive HP detection
FSTHPD
Staple shift HP detection
FSD
Staple empty detection
FSTD
Needle lead edge position detection
FFANLK
Fan motor lock detection
FSJOGD
Stapler alignment interference detection
FSAD
Staple safety SW
FSSUC
Saddle staple unit detection
FSHTD
Shutter open detection
FCD
Upper door open detection
FFDD
Front cover open detection
F24V
24V output interruption detection
FPSW1
PUSHSW1 detection
FPSW2
PUSHSW2 detection
FPSW3
PUSHSW3 detection
SIMULATION NO.02-03
TEST
DSPF OUTPUT CHECK
1/1
CLOSE
SPUM
SPFM
SPOM
SLUM
SPFFAN
SPFC
SRRC
SRRBC
STRRC
STRRBC
STRC
EXECUTE
STMPS
MX-7000N SIMULATION 7 – 12
<4K finisher DIPSW>
<4K saddle finisher>
<4K saddle finisher DIPSW>
<4K finisher/4K saddle finisher punch unit>
3-3
Purpose
Operation test/Check
Function (Purpose) Used to check the operation of the load in
the finisher and the control circuit.
Section
Finisher
Operation/Procedure
1)
1)
Select a target of the operation check with the touch panel.
2)
Press [EXECUTE] key.
The selected load is operated.
When [EXECUTE] is pressed, the operation is stopped.
The selected load is operated.
When [EXECUTE] is pressed, the operation is stopped.
<4K finisher>
<4K saddle finisher saddle section>
<External punch unit>
FAED21
Tray 2 area detection 1
FAED22
Tray 2 area detection 2
FAED23
Tray 2 area detection 3
FDSW1
DIPSW1 detection
FDSW2
DIPSW2 detection
FDSW3
DIPSW3 detection
FDSW4
DIPSW4 detection
FDSW5
DIPSW5 detection
FDSW6
DIPSW6 detection
FDSW7
DIPSW7 detection
FDSW8
DIPSW8 detection
FSPIND
Saddle entry port paper detection
FSPDD
Saddle paper exit detection
FSDTPD
Saddle tray paper detection
FS1PD
Saddle paper detection 1
FS2PD
Saddle paper detection 2
FS3PD
Saddle paper detection 3
FSLGE
Paper pushing plate motor lock detection
FSLGHPD
Paper pushing plate HP detection
FSLGTD
Paper pushing plate lead edge position detection
FSFOE
Paper folding motor lock detection
FSFOHPD
Paper folding HP detection
FSPPHPD
Paper positioning plate HP detection
FSPPPD
Paper positioning plate paper detection
FSAHPD
Alignment plate HP detection
FSSIND
Stitcher storage detection
FSVPPD
Vertical path paper detection
FSCRPD
Semi-circular roller phase detection
FSGHPD
Guide HP detection
FSSHP1
Stitch operation HP detection 1
FSSHP2
Stitch operation HP detection 2
FSSD1
Saddle needle presence detection 1
FSSD2
Saddle needle presence detection 2
FSAHPC
Alignment HP sensor connector connection detection
FSFOHPC
Paper folding HP sensor connector connection detection
FSEJDC
Paper exit door sensor connector connection detection
FSFDC
Front door open/close sensor connector connection
detection
detection
FSPPHPC
Paper positioning plate HP sensor connector connection
detection
detection
FSLGTC
Paper pushing plate lead edge sensor connector
connection detection
connection detection
FSINDD
Inlet port cover open detection
FSEJDD
Paper exit cover open detection
FSINDSW
Saddle inlet port door detection
FSFDSW
Front door open detection SW
FSEJDSW
Paper exit door open detection SW
FSPSW1
S-PUSHSW detection
FSBHPC
Paper pushing plate HP sensor connector connection
detection
detection
FSDSW1
S-DIPSW1 detection
FSDSW2
S-DIPSW2 detection
FSDSW3
S-DIPSW3 detection
FSDSW4
S-DIPSW4 detection
FSDSW5
S-DIPSW5 detection
FSDSW6
S-DIPSW6 detection
FSDSW7
S-DIPSW7 detection
FSDSW8
S-DIPSW8 detection
FPE
Punch motor lock detection
FPUC
Punch unit connection detection
FPHPD
Punch HP detection
FPSHPD
Punch horizontal resist HP detection
FPFDD
Punch front door open detection
FPDD
Punch dust detection
FPUDSW
Punch upper cover open/close detection SW
FINRPS
Entry port reverse path solenoid
FJPM
Interface transport motor
FJFM
Interface transport fan motor
FFM
Entry port transport motor
FAM
Bundle paper exit motor
FFJM
Alignment motor front
FRJM
Alignment motor rear
FSM
Staple shift motor
FTLM1
Tray 1 lift motor
FTLM2
Tray 2 lift motor
FFSM
Staple motor
FSWM
Oscillation motor
FASM
Rear edge assist motor
FINRRS
Inlet port roller separation solenoid
FBRRS
Buffer roller separation solenoid
FFDRRS
Paper exit roller separation solenoid
FBES
Buffer rear edge holding solenoid
FSHC
Shutter open/close clutch
FAORC
Bundle exit lower roller clutch
FSIFM
Saddle entry port transport motor
FSFM
Saddle transport motor
FSFOM
Paper folding motor
FSGM
Guide motor
FSJM
Saddle alignment motor
FSFSTM
Stitch motor front
FSRSTM
Stitch motor motor rear
FSLGM
Paper holding motor
FSFS
Saddle flapper solenoid
FS1DFS
Paper deflection plate 1 solenoid
FS2DFS
Paper deflection plate 2 solenoid
FSFCS
Transport plate contact solenoid
FPPM
Paper positioning motor
FPNM
Punch motor
FPSM
Punch horizontal resist motor
FIN SENSOR CHECK
CLOSE
SIMULATION NO.03-02
TEST
1/1
FJPID
FJPOD
FJPDD
FED
FAED1
FAED2
FAED3
FFJHPD
FSTHPD
FSD
FSTD
FFANLK
FRJHPD
FBED1
FBED2
FCCD
FSLD1
FPDD1
FSLD2
FASHPD
FSWHPD
FSWOPD
FSTPD
FSHPD
FSJOGD
FSAD
FSSUC
FSHTD
FCD
FFDD
F24V
FPSW1
FPSW2
FPSW3
FAED21
FAED22
FAED23
MX-7000N SIMULATION 7 – 13
3-10
Purpose
Adjustment
Function (Purpose) Used to adjust the finisher.
Section
Section
Finisher
Operation/Procedure
1)
1)
Select an item corresponding to the adjustment content with
[
[
↑] and [↓] keys on the touch panel.
2)
Enter the adjustment value with 10-key.
3)
Press [OK] key. (The set value is saved.)
<4K finisher>
<4K saddle finisher>
3-30
Purpose
Operation test/Check
Function (Purpose) Used to check the operations of the sen-
sors and detectors in the inserter and the
control circuits.
control circuits.
Section
Inserter
Operation/Procedure
The operating conditions of the sensors and detectors are dis-
played.
Sensors and detectors which are turned on are highlighted.
The operating conditions of the sensors and detectors are dis-
played.
Sensors and detectors which are turned on are highlighted.
3-31
Purpose
Operation test/Check
Function (Purpose) Used to check the operations of the loads
in the inserter and the control circuit.
Section
Inserter
Operation/Procedure
1)
1)
Select a target of the operation check with the touch panel.
2)
Press [EXECUTE] key.
The selected load is operated.
When [EXECUTE] is pressed, the operation is stopped.
The selected load is operated.
When [EXECUTE] is pressed, the operation is stopped.
Item
Display
Item
Set
range
Default
value
A
FRONT
ADJUST
ADJUST
Alignment position
adjustment (front)
adjustment (front)
0 - 20
10
B
STAPLE
REAR
REAR
Staple binding position
adjustment (one position
at the rear)
adjustment (one position
at the rear)
94 - 106
100
C
STAPLE
FRONT
FRONT
Staple binding position
adjustment (one position
in front)
adjustment (one position
in front)
94 - 106
100
D
PUNCH
CENTER
CENTER
Punch center adjustment
30 - 70
50
E
PUNCH HOLE
Punch hole position
adjustment
adjustment
46 - 52
50
Item
Display
Item
Set
range
Default
value
A
SADDLE
POSITION
POSITION
Saddle binding position
adjustment
adjustment
197 - 203
200
B
FOLDING
POSITION
POSITION
Saddle folding position
adjustment
adjustment
192 - 208
200
C
FRONT
ADJUST
ADJUST
Alignment position
adjustment (front)
adjustment (front)
0 - 20
10
D
STAPLE
REAR
REAR
Staple binding position
adjustment (one position
at the rear)
adjustment (one position
at the rear)
94 - 106
100
E
STAPLE
FRONT
FRONT
Staple binding position
adjustment (one position
in front)
adjustment (one position
in front)
94 - 106
100
F
PUNCH
CENTER
CENTER
Punch center adjustment
30 - 70
50
G
PUNCH HOLE
Punch hole position
adjustment
adjustment
46 - 52
50
SIMULATION NO.03-03
TEST
FIN LOAD CHECK
EXECUTE
1/1
CLOSE
FINRPS
FJPM
FJFM
FFM
FAM
FFJM
FRJM
FSM
FTLM1
FTLM2
FFSM
FSWM
FASM
FINRRS
FBRRS
FFDRRS
FBES
FSHC
FAORC
TH_SEN
Inserter sub tray pull-out detection
TS_SEN
Inserter sub tray storage detection
T_SEN
Inserter tray paper length detection
EMP_SEN
Inserter tray empty detection
REG_SEN
Inserter resist detection
TIM_SEN
Inserter timing detection
JCK_SEN
Inserter JAM cover open/close detection
H_SEN
Inserter reverse detection
HI_SEN
Inserter paper exit detection
HYK_SEN
Inserter reverse unit open/close detection
P_ST_SW
Inserter start SW
P_MO_SW
Inserter staple mode select SW
P_PN_SW
Inserter punch select SW
SET_SW
Inserter set SW
K_MOT
Inserter paper feed motor
Y_MOT
Inserter horizontal transport motor
H_MOT
Inserter reverse motor
F_SOL
Inserter flapper solenoid
A : 10
;
FRONT ADJUST
B : 100
;
STAPLE REAR
C : 100
;
STAPLE FRONT
D : 50
;
PUNCH CENTER
A:
SIMULATION NO.03-10
FINISHER ADJUSTMENT
10
0
20
OK
TEST
CLOSE
E : 50
;
PUNCH HOLE
FIN SENSOR CHECK
CLOSE
SIMULATION NO.03-30
TEST
1/1
TH_SEN
TS_SEN
T_SEN
EMP_SEN
REG_SEN
TIM_SEN
JCK_SEN
H_SEN
HI_SEN
HYK_SEN
P_ST_SW
P_MO_SW
P_PN_SW
SET_SW
MX-7000N SIMULATION 7 – 14
3-32
Purpose
Setting (Adjustment)
Function (Purpose) Used to set the adjustment value of the
inserter paper width detection level.
Section
Inserter
Operation/Procedure
1)
1)
Select an item corresponding to the adjustment content with
[
[
↑] and [↓] keys on the touch panel.
2)
Enter the adjustment value with 10-key.
3)
Press [OK] key. (The set value is saved.)
4
4-2
Purpose
Operation test/Check
Function (Purpose) Used to check the operations of the sen-
sors and detectors in the large capacity tray
(LCC) and the control circuit.
(LCC) and the control circuit.
Section
Large capacity tray (LCC)
Operation/Procedure
The operating conditions of the sensors and detectors are dis-
played.
Sensors and detectors which are turned on are highlighted.
The operating conditions of the sensors and detectors are dis-
played.
Sensors and detectors which are turned on are highlighted.
<A4 LCC>
<A3 LCC>
4-3
Purpose
Operation test/Check
Function (Purpose) Used to check the operations of the loads
in the large capacity tray (LCC) and the
control circuit.
control circuit.
Section
Large capacity tray (LCC)
Operation/Procedure
1)
1)
Select a target of the operation check with the touch panel.
2)
Press [EXECUTE] key.
The selected load is operated.
When [EXECUTE] is pressed, the operation is stopped.
The selected load is operated.
When [EXECUTE] is pressed, the operation is stopped.
<A4 LCC>
R_CL
Inserter resist clutch
P_LED
Inserter operation panel upper LED
Item
Display
Item
Set
range
A
MAX. POSITION
Inserter tray width detection
adjustment value (Max. width)
adjustment value (Max. width)
0 - 1023
B
POSITION 1
Inserter tray width detection
adjustment value (Adjustment
position 1)
adjustment value (Adjustment
position 1)
0 - 1023
C
POSITION 2
Inserter tray width detection
adjustment value (Adjustment
position 2)
adjustment value (Adjustment
position 2)
0 - 1023
D
MIN. POSOTION
Inserter tray width detection
adjustment value (Min. width)
adjustment value (Min. width)
0 - 1023
SIMULATION NO.03-31
TEST
INSERTER LOAD CHECK
1/1
CLOSE
K_MOT
Y_MOT
H_MOT
F_SOL
R_CL
P_LED
EXECUTE
A : 72
;
MAX. POSITION
B : 200
;
POSITION1
C : 10
;
POSITION2
D : 100
;
MIN. POSITION
A:
SIMULATION NO.03-32
INSERTER TRAY VALUE SETTING
72
0 1023
OK
TEST
CLOSE
LPFD
LCC transport sensor
LUD
LCC tray upper limit detection
LDD
LCC tray lower limit detection
LPED
LCC tray paper empty detection
LCD
LCC tray insertion detection
LDSW
LCC upper open/close detection SW
LRE
LCC lift motor encoder detection
L24VM
LCC 24V power monitor
LLSW
LCC upper limit SW
LTOD
LCC main unit connection detection
LPFD
LCC transport sensor
LUD
LCC tray upper limit detection
LDD
LCC tray lower limit detection
LPED
LCC tray paper empty detection
LCD
LCC tray insertion detection
LDSW
LCC upper open/close detection SW
LRE
LCC lift motor encoder detection
L24VM
LCC 24V power monitor
LLSW
LCC upper limit SW
LPUSW
LCC paper upper surface detection SW
LRRSW
LCC reverse winding detection SW
LTLSW
LCC tray lift SW
LTLD
LCC tray lock sensor
LIPSW
LCC illegal paper detection SW
LTOD
LCC main unit connection sensor
LPFM
LCC transport motor
LLM
LCC lift motor
LPFC
LCC paper feed clutch
LPFS
LCC paper feed solenoid
LTRC
LCC transport clutch
LCC SENSOR CHECK
CLOSE
SIMULATION NO.04-02
TEST
1/1
LPFD
LUD
LDD
LPED
LCD
LDSW
LRE
L24VM
LLSW
LTOD
Click on the first or last page to see other MX-5500N / MX-6200N / MX-7000N (serv.man46) service manuals if exist.