DOWNLOAD Sharp MX-5500N / MX-6200N / MX-7000N (serv.man4) Service Manual ↓ Size: 83.06 KB | Pages: 2 in PDF or view online for FREE

Model
MX-5500N MX-6200N MX-7000N (serv.man4)
Pages
2 Few pages! See other manuals at the bottom of the first or last page.
Size
83.06 KB
Type
PDF
Document
Handy Guide
Brand
Device
Copying Equipment / GENERAL PROCEDURE FOR COLOUR CALIBRATION SET-UP
File
mx-5500n-mx-6200n-mx-7000n-sm4.pdf
Date

Sharp MX-5500N / MX-6200N / MX-7000N (serv.man4) Handy Guide ▷ View online

Sharp Electronics (UK) Ltd., Technical Services Group
Calibration
10. Execute SIM 44-27, clearing half tone process control correction values
11. Execute SIM 44-06, forced execution of process control
12. Execute SIM 44-26, forced execution of half tone image correction
NOTE: At this stage if an error occurs, proceed to step 13 and then step 17, after this
come back to step 12 and continue with the rest of the calibration procedure.
13. Ensure good quality A3 colour copy paper is in the machine and perform the Engine
Auto Colour Calibration by executing SIM 46-24
TIPS: Select “FACTORY” method when calibrating. When putting the calibration page on
the glass lay 5 sheets of clean A3 paper on top. Inspect the Self print of 16 patches
test sheet and check that the half tones end in about the same position for all colours,
if not select repeat and go through the same process again (this can be repeated up to
4 times)
If the customer is unhappy with the colour quality a new definition (DEF1, DEF2 or DEF3)
for FACTORY mode can be set in SIM 63-11 (see below). If this is done then step 13
will need to be repeated. THIS WILL AFFECT ALL COLOURS
14. Perform colour copy density adjustments for all modes in SIM 46-01, refer to relevant
section of service manual
15. Perform Black and white density adjustment in all modes by executing SIM46-02
using Sharp Grey Chart; refer to relevant section of service manual
16. Execute SIM 67-31, used to clear the printer calibration value
17. Ensure good quality A3 colour copy paper is in the machine and perform the Printer
Auto Colour Calibration by executing SIM 67-24 (same as step 13)
NOTE: New definition for FACTORY mode can also be set for printer in SIM 67-26, if a
different target is selected repeat step 15.
Sharp Electronics (UK) Ltd., Technical Services Group
Calibration
10. Execute SIM 44-27, clearing half tone process control correction values
11. Execute SIM 44-06, forced execution of process control
12. Execute SIM 44-26, forced execution of half tone image correction
NOTE: At this stage if an error occurs, proceed to step 13 and then step 17, after this
come back to step 12 and continue with the rest of the calibration procedure.
13. Ensure good quality A3 colour copy paper is in the machine and perform the Engine
Auto Colour Calibration by executing SIM 46-24
TIPS: Select “FACTORY” method when calibrating. When putting the calibration page on
the glass lay 5 sheets of clean A3 paper on top. Inspect the Self print of 16 patches
test sheet and check that the half tones end in about the same position for all colours,
if not select repeat and go through the same process again (this can be repeated up to
4 times)
If the customer is unhappy with the colour quality a new definition (DEF1, DEF2 or DEF3)
for FACTORY mode can be set in SIM 63-11 (see below). If this is done then step 13
will need to be repeated. THIS WILL AFFECT ALL COLOURS
14. Perform colour copy density adjustments for all modes in SIM 46-01, refer to relevant
section of service manual
15. Perform Black and white density adjustment in all modes by executing SIM46-02
using Sharp Grey Chart; refer to relevant section of service manual
16. Execute SIM 67-31, used to clear the printer calibration value
17. Ensure good quality A3 colour copy paper is in the machine and perform the Printer
Auto Colour Calibration by executing SIM 67-24 (same as step 13)
NOTE: New definition for FACTORY mode can also be set for printer in SIM 67-26, if a
different target is selected repeat step 15.
Sharp Electronics (UK) Ltd., Technical Services Group
Calibration
10. Execute SIM 44-27, clearing half tone process control correction values
11. Execute SIM 44-06, forced execution of process control
12. Execute SIM 44-26, forced execution of half tone image correction
NOTE: At this stage if an error occurs, proceed to step 13 and then step 17, after this
come back to step 12 and continue with the rest of the calibration procedure.
13. Ensure good quality A3 colour copy paper is in the machine and perform the Engine
Auto Colour Calibration by executing SIM 46-24
TIPS: Select “FACTORY” method when calibrating. When putting the calibration page on
the glass lay 5 sheets of clean A3 paper on top. Inspect the Self print of 16 patches
test sheet and check that the half tones end in about the same position for all colours,
if not select repeat and go through the same process again (this can be repeated up to
4 times)
If the customer is unhappy with the colour quality a new definition (DEF1, DEF2 or DEF3)
for FACTORY mode can be set in SIM 63-11 (see below). If this is done then step 13
will need to be repeated. THIS WILL AFFECT ALL COLOURS
14. Perform colour copy density adjustments for all modes in SIM 46-01, refer to relevant
section of service manual
15. Perform Black and white density adjustment in all modes by executing SIM46-02
using Sharp Grey Chart; refer to relevant section of service manual
16. Execute SIM 67-31, used to clear the printer calibration value
17. Ensure good quality A3 colour copy paper is in the machine and perform the Printer
Auto Colour Calibration by executing SIM 67-24 (same as step 13)
NOTE: New definition for FACTORY mode can also be set for printer in SIM 67-26, if a
different target is selected repeat step 15.
Sharp Electronics (UK) Ltd., Technical Services Group
Calibration
10. Execute SIM 44-27, clearing half tone process control correction values
11. Execute SIM 44-06, forced execution of process control
12. Execute SIM 44-26, forced execution of half tone image correction
NOTE: At this stage if an error occurs, proceed to step 13 and then step 17, after this
come back to step 12 and continue with the rest of the calibration procedure.
13. Ensure good quality A3 colour copy paper is in the machine and perform the Engine
Auto Colour Calibration by executing SIM 46-24
TIPS: Select “FACTORY” method when calibrating. When putting the calibration page on
the glass lay 5 sheets of clean A3 paper on top. Inspect the Self print of 16 patches
test sheet and check that the half tones end in about the same position for all colours,
if not select repeat and go through the same process again (this can be repeated up to
4 times)
If the customer is unhappy with the colour quality a new definition (DEF1, DEF2 or DEF3)
for FACTORY mode can be set in SIM 63-11 (see below). If this is done then step 13
will need to be repeated. THIS WILL AFFECT ALL COLOURS
14. Perform colour copy density adjustments for all modes in SIM 46-01, refer to relevant
section of service manual
15. Perform Black and white density adjustment in all modes by executing SIM46-02
using Sharp Grey Chart; refer to relevant section of service manual
16. Execute SIM 67-31, used to clear the printer calibration value
17. Ensure good quality A3 colour copy paper is in the machine and perform the Printer
Auto Colour Calibration by executing SIM 67-24 (same as step 13)
NOTE: New definition for FACTORY mode can also be set for printer in SIM 67-26, if a
different target is selected repeat step 15.
Display

Sharp MX-5500N / MX-6200N / MX-7000N (serv.man4) Handy Guide ▷ Download

  • DOWNLOAD Sharp MX-5500N / MX-6200N / MX-7000N (serv.man4) Service Manual ↓ Size: 83.06 KB | Pages: 2 in PDF or view online for FREE
  • Here you can View online or download the Handy Guide for the Sharp MX-5500N / MX-6200N / MX-7000N (serv.man4) in PDF for free, which will help you to disassemble, recover, fix and repair Sharp MX-5500N / MX-6200N / MX-7000N (serv.man4) Copying Equipment. Information contained in Sharp MX-5500N / MX-6200N / MX-7000N (serv.man4) Handy Guide (repair manual) includes:
  • Disassembly, troubleshooting, maintenance, adjustment, installation and setup instructions.
  • Schematics, Circuit, Wiring and Block diagrams.
  • Printed wiring boards (PWB) and printed circuit boards (PCB).
  • Exploded View and Parts List.