DOWNLOAD Sharp MX-5500N / MX-6200N / MX-7000N (serv.man33) Service Manual ↓ Size: 3.72 MB | Pages: 13 in PDF or view online for FREE

Model
MX-5500N MX-6200N MX-7000N (serv.man33)
Pages
13
Size
3.72 MB
Type
PDF
Document
Peripheral
Brand
Device
Copying Equipment / MX-LCX3 LCT A3-Installation Manual
File
mx-5500n-mx-6200n-mx-7000n-sm33.pdf
Date

Sharp MX-5500N / MX-6200N / MX-7000N (serv.man33) Peripheral ▷ View online

MX-7000N  MX-LCX3  3 – 6
<2>
Turn the adjustment screw above to adjust the height.
After adjustment with the adjustment screw, tighten the screws
on the both ends of the caster movable plate which were loos-
ened in the previous procedure.
NOTE: Adjust so that the marks on the left and the right sides
of the caster movable plate and the lead edge of the triangular
hole are at the same height.
<3>
Check the height in procedure C-1). If the height is not proper,
go to <2>. If the height is proper, install the positioning plates
to the front and the rear sides and fix them with the fixing
screws B (1 pc. for each side).
Front side
Rear side
c. If the upper section of the LCC left side is locked first
and the positioning plate cannot be inserted :
<1>
Loosen the caster screw in the lower section of the LCC right
side.
<2>
Turn the adjuster to lower the LCC right side.
<3>
Tighten the caster screw.
Right side
<4>
Check the height in procedure 1). If the height is not proper,
separate the LCC (the procedure is described later) and go to
"b".
If the height is proper, install the positioning plates to the front
and the rear sides with fixing screws B.
Since the LCC may be moved by the paper weight
when closing the tray, the adjuster must be securely
on the floor.
MX-7000N  MX-LCX3  3 – 7
Front side
Rear side
2)
Check to confirm that the upper section of the LCC left side is
locked.
After checking, lower the adjuster on the lower section of the
LCC right side until it does not rotate.
Locked state
Adjuster section
- When the upper side is not locked
Raise the adjuster on the lower side of the LCC right side until
the hole shown in the figure below comes at the center, and
check that it is locked.
* If lock is incomplete, when the power switch is turned on, the
message, "Check installation of tray 5" is displayed on the
operation panel.
1)
Check that the right caster section is grounded.
Loosen two screws on the lower side of the LCC right side,
ground the caster on the floor, and tighten the screws.
2)
Installation of the left front cabinet
Engage the pawls of the left front cabinet (Package part No. 5)
with the five square holes in the left front side of the LCC, and
press the left front cabinet and fix with the fixing screw C
(Package part No. 8) (1 pc.).
F
MX-7000N  MX-LCX3  3 – 8
[How to separate the LCC from the machine]
1)
Remove the left front cabinet of the LCC.
2)
Remove the positioning plate installed to the front and the rear
sides of the left lower side of the LCC.
Front side
Rear side
3)
Raise the adjuster installed to the front and the rear sides of
the lower section of the LCC right side.
4)
Push the resin cover beneath the lock section on the top of the
left side of the LCC and shift the LCC to the right. Release the
top lock.
5)
Shift the LCC to the right to separate.
D. Connector connection
1)
Remove the screw (one for each) from the connector covers
on the main unit and then remove the connector covers
(2pcs.).
2)
Connect the large capacity tray interface harness connector
(a) and the heating heater interface harness connector (b) to
the main unit connector, and tighten the connector screw to fix
the connector.
a
b
MX-7000N  MX-LCX3  3 – 9
E. Select the paper size
1)
Slowly pull out the paper feed base tray until it stops.
2)
Side plate size changeover
<1>
Loosen the wing bolt (A) on the front and the rear side of the
LCC upper part, and slide the handle to the neutral position.
<2>
Move the side plate to the desired paper size position.
<3>
Slide the handle to the desired paper size position, and lock it
and tighten the wing bolt (A).
3)
Rear edge plate size changeover
<1>
Lift the MC-CL handle at the top of the rear edge plate and
shift it to the desired paper size position.
<2>
Insert the lead edge of the movable shaft into the hole in the
lower section of the rear edge plate with the upper lever, and
lock the rear edge plate to the desired paper size position.
<3>
Push the large capacity tray slowly into the original position.
F. Turn ON the main power switch of the main 
unit
1)
Connect the power plug of the main unit into the power outlet.
A3/A4
12/A3W
11
8.5
A4R
B4/B5
A3/A4
12/A3W
11
8.5
A4R
B4/B5
A
A
Page of 13
Display

Click on the first or last page to see other MX-5500N / MX-6200N / MX-7000N (serv.man33) service manuals if exist.