DOWNLOAD Sharp MX-5500N / MX-6200N / MX-7000N (serv.man33) Service Manual ↓ Size: 3.72 MB | Pages: 13 in PDF or view online for FREE

Model
MX-5500N MX-6200N MX-7000N (serv.man33)
Pages
13
Size
3.72 MB
Type
PDF
Document
Peripheral
Brand
Device
Copying Equipment / MX-LCX3 LCT A3-Installation Manual
File
mx-5500n-mx-6200n-mx-7000n-sm33.pdf
Date

Sharp MX-5500N / MX-6200N / MX-7000N (serv.man33) Peripheral ▷ View online

MX-7000N  MX-LCX3  3 – 3
2)
Open the front cabinet of the main unit. Turn OFF the power
switch in the front cabinet.
3)
Disconnect the power plug of the main unit from the power out-
let.
B. Attach the mounting plate upper and the lower 
front/rear connecting plate
1)
Attach the mounting plate upper (Package part No. 1) with the
fixing screw A (Package part No. 6) to the installation part of
right side of the main unit. When installing, put the rubber sec-
tion (
) of the mounting plate upper on the lower side.
2)
Remove the fixing screws of the front/rear cover on the lower
part of the main unit. Attach the connecting plate lower front
(Package part No. 2) to the lower front side of the main unit
with the fixing screw B (Package part No. 7).
Attach the connecting plate lower rear (Package part No. 3) to
the lower rear side of the main unit with the fixing screw B
(Package part No. 7).
3)
Release the lock, and open the right door.
4)
Remove the screws, and remove the upper cover.
5)
Close the right door.
"OFF"
MX-7000N  MX-LCX3  3 – 4
6)
Remove the two fixing screws of the machine entry port, and
remove the entry port cover.
7)
Attach the entry port cover reversely to the machine and fix it
with the two fixing screws which was removed in procedure 3.
* When working, be careful to prevent damage of the paper
pass (transport) surface on the entry port cover.
8)
Release the lock, and open the right door.
9)
Install the upper cover, and fix with screws.
10) Close the right door.
C. Installation to the main unit and height 
adjustment
1)
Use the edge of the connection plates F/R mounted to the
lower side of the machine and the mark on the mounting plate
in the lower left side of the LCC to check the installation height.
Front side
Rear side
MX-7000N  MX-LCX3  3 – 5
a. When the height is properly adjusted:
When both the edges of the connecting plates on front and
rear are fit with the longest mark on the mounting plates each,
install the positioning plates (Package part No. 4) to the front
and the rear sides and fix them with the fixing screw B (Pack-
age part No. 7) (1 for each side).
Front side
Rear side
b. When the height is not properly adjusted:
Use the adjustment device on the lower left side of the LCC to
adjust the height of the left caster section.
Front side
Rear side
<1>
Loosen the hex washer based screws on the both ends of the
caster movable plate in the front and the rear sides.
F
R
MX-7000N  MX-LCX3  3 – 6
<2>
Turn the adjustment screw above to adjust the height.
After adjustment with the adjustment screw, tighten the screws
on the both ends of the caster movable plate which were loos-
ened in the previous procedure.
NOTE: Adjust so that the marks on the left and the right sides
of the caster movable plate and the lead edge of the triangular
hole are at the same height.
<3>
Check the height in procedure C-1). If the height is not proper,
go to <2>. If the height is proper, install the positioning plates
to the front and the rear sides and fix them with the fixing
screws B (1 pc. for each side).
Front side
Rear side
c. If the upper section of the LCC left side is locked first
and the positioning plate cannot be inserted :
<1>
Loosen the caster screw in the lower section of the LCC right
side.
<2>
Turn the adjuster to lower the LCC right side.
<3>
Tighten the caster screw.
Right side
<4>
Check the height in procedure 1). If the height is not proper,
separate the LCC (the procedure is described later) and go to
"b".
If the height is proper, install the positioning plates to the front
and the rear sides with fixing screws B.
Since the LCC may be moved by the paper weight
when closing the tray, the adjuster must be securely
on the floor.
Page of 13
Display

Sharp MX-5500N / MX-6200N / MX-7000N (serv.man33) Peripheral ▷ Download

  • DOWNLOAD Sharp MX-5500N / MX-6200N / MX-7000N (serv.man33) Service Manual ↓ Size: 3.72 MB | Pages: 13 in PDF or view online for FREE
  • Here you can View online or download the Peripheral for the Sharp MX-5500N / MX-6200N / MX-7000N (serv.man33) in PDF for free, which will help you to disassemble, recover, fix and repair Sharp MX-5500N / MX-6200N / MX-7000N (serv.man33) Copying Equipment. Information contained in Sharp MX-5500N / MX-6200N / MX-7000N (serv.man33) Peripheral (repair manual) includes:
  • Disassembly, troubleshooting, maintenance, adjustment, installation and setup instructions.
  • Schematics, Circuit, Wiring and Block diagrams.
  • Printed wiring boards (PWB) and printed circuit boards (PCB).
  • Exploded View and Parts List.