DOWNLOAD Sharp MX-5500N / MX-6200N / MX-7000N (serv.man33) Service Manual ↓ Size: 3.72 MB | Pages: 13 in PDF or view online for FREE

Model
MX-5500N MX-6200N MX-7000N (serv.man33)
Pages
13
Size
3.72 MB
Type
PDF
Document
Peripheral
Brand
Device
Copying Equipment / MX-LCX3 LCT A3-Installation Manual
File
mx-5500n-mx-6200n-mx-7000n-sm33.pdf
Date

Sharp MX-5500N / MX-6200N / MX-7000N (serv.man33) Peripheral ▷ View online

MX-7000N  MX-LCX3  3 – 11
(2) Mechanical adjustment-1
Since the off-center adjustment has been made at shipping, there
is normally no need to adjust. If the center is shifted, however,
adjust with the simulation. If the shift is not recovered, perform the
following steps to adjust.
<1>
Slowly pull out the paper feed base tray until it stops.
[When shifted to the front side]
When shifting the line of printing from the center of the paper in the
direction A of arrow as shown below:
<2>
Loosen the blue off-center adjustment screws (each 2 pcs.), and
move the side plate by the dimension shifted in the direction A (R
side), and tighten the loosened blue screws.
NOTE: Move the side plates by the same dimension on the front
side and the rear side.
<3>
Push the large capacity tray slowly into the original position.
Then make a copy again to check to insure that there is no more
shifet. Repeat this procedure as required.
[When shifted to the rear side]
When shifting the line of printing from the center of the paper in the
B direction of arrow as shown below:
<2>
Loosen the blue off-center adjustment screws (each 2 pcs.), and
move the side plate by the dimension shifted in the direction B (F
side), and tighten the loosened blue screws.
NOTE: Move the side plates by the same dimension on the front
side and the rear side.
MX-7000N  MX-LCX3  3 – 12
<3>
Push the large capacity tray slowly into the original position.
Then make a copy again to check to insure that there is no more
shifet. Repeat this procedure as required.
(3) Mechanical adjustment-2
Since the regulation plates are adjusted when shipping, there is
basically no need to readjust. If, however, diagonal feed is poorly
operated, adjust the regulation plate width and the diagonal feed in
the following procedures:
a. Regulation plate width adjustment
1)
Press the lock button on the front cabinet and lower the paper
feed base tray to the paper supply position. Pull out the large
capacity tray.
2)
Set a sheet of paper on the paper feed base tray. Check that
the front regulation plate is at the marked center, and push it in
contact with the front regulation plate. Loosen the blue screws
of the rear regulation plate.
3)
Use the mark of the rear regulation plate, and fix the blue
screws at the position so that the clearance between paper
and the rear regulation plate is evenly 1mm.
NOTE: The positions of the regulation plates are even to the right
and left marks.
1mm
MX-7000N  MX-LCX3  3 – 13
b. Diagonal feed adjustment
1)
Press the lock button on the front cabinet and lower the paper
feed base tray to the paper supply position. Pull out the tray.
2)
Adjust the diagonal feed.
[In the case of diagonal feed 1]
Loosen the blue screw (A) on the front regulation plate.
Referring to the degree of diagonal feed, move the regulation
plate in the direction of (-) and fix the blue screw.
[In the case of diagonal feed 2]
Loosen the blue screw (A) on the front regulation plate.
Referring to the degree of diagonal feed, move the regulation
plate in the direction of (+) and fix the blue screw.
3)
Set a sheet of paper on the paper feed base tray and adjust
the regulation plate width. (Refer to "a. Regulation plate width
adjustment.")
* After completion of the adjustment, check that the front regu-
lation plate and the rear regulation plate are in parallel to
each other.
Diagonal feed 1
Transport
direction
Diagonal feed 2
1
3
2
3
A
1
A
2
3
MX-7000N  MX-LCX3  3 – 13
b. Diagonal feed adjustment
1)
Press the lock button on the front cabinet and lower the paper
feed base tray to the paper supply position. Pull out the tray.
2)
Adjust the diagonal feed.
[In the case of diagonal feed 1]
Loosen the blue screw (A) on the front regulation plate.
Referring to the degree of diagonal feed, move the regulation
plate in the direction of (-) and fix the blue screw.
[In the case of diagonal feed 2]
Loosen the blue screw (A) on the front regulation plate.
Referring to the degree of diagonal feed, move the regulation
plate in the direction of (+) and fix the blue screw.
3)
Set a sheet of paper on the paper feed base tray and adjust
the regulation plate width. (Refer to "a. Regulation plate width
adjustment.")
* After completion of the adjustment, check that the front regu-
lation plate and the rear regulation plate are in parallel to
each other.
Diagonal feed 1
Transport
direction
Diagonal feed 2
1
3
2
3
A
1
A
2
3
Page of 13
Display

Sharp MX-5500N / MX-6200N / MX-7000N (serv.man33) Peripheral ▷ Download