DOWNLOAD Sharp MX-5500N / MX-6200N / MX-7000N (serv.man32) Service Manual ↓ Size: 1.84 MB | Pages: 9 in PDF or view online for FREE

MX-7000N  MX-LCX2  2 – 9

2)

Loosen the stopper fixing screw (1 pc.) on the lower right side
of the paper feed tray to disable the stopper function.

3)

Then pull out the paper feed tray again until it stops.

[When shifted to the front side]
To adjust the print line in the direction A from the paper center as
shown in the figure:
1)

Loosen the red fixing screws (2 pcs. for each) of the front/back
size guide adjustment plate, and slide the side guide adjust-
ment plate in the direction A (R side) by the shift dimension.
Tighten the red fixing screws (2 pcs. for each). Slide the auxil-
iary guide in the direction of A by the same dimension.

Slightly push the paper feed tray into the machine. Return the
stopper to the original position, and fix it with the fixing screw
(1 pc.). 
At that time, check that the stopper pawl is engaged with the
stopper receiver of the large capacity tray.

2)

Push the large capacity tray slowly into the original position.

Then make a copy to check to insure that there is no more shift.
Repeat the procedures until there is no shift.
[When shifted to the rear side]
To adjust the print line in the direction B from the paper center as
shown in the figure:
1)

Loosen the red fixing screws (2 pcs. for each) of the front/back
size guide adjustment plate, and slide the side guide adjust-
ment plate in the direction B (F side) by the shift dimension.
Tighten the red fixing screws (2 pcs. for each), and slightly
push the paper feed tray into the machine. Return the stopper
to the original position, and fix it with the fixing screw (1 pc.).
Slide the auxiliary guide in the direction of B by the same
dimension.
At that time, check that the stopper pawl is engaged with the
stopper receiver of the large capacity tray.

2)

Push the large capacity tray slowly into the original position.

Then make a copy to check to insure that there is no more shift.
Repeat the procedures until there is no shift.

A

R side

F side

B

R side

F side

MX-7000N  MX-LCX2  2 – 9

2)

Loosen the stopper fixing screw (1 pc.) on the lower right side
of the paper feed tray to disable the stopper function.

3)

Then pull out the paper feed tray again until it stops.

[When shifted to the front side]
To adjust the print line in the direction A from the paper center as
shown in the figure:
1)

Loosen the red fixing screws (2 pcs. for each) of the front/back
size guide adjustment plate, and slide the side guide adjust-
ment plate in the direction A (R side) by the shift dimension.
Tighten the red fixing screws (2 pcs. for each). Slide the auxil-
iary guide in the direction of A by the same dimension.

Slightly push the paper feed tray into the machine. Return the
stopper to the original position, and fix it with the fixing screw
(1 pc.). 
At that time, check that the stopper pawl is engaged with the
stopper receiver of the large capacity tray.

2)

Push the large capacity tray slowly into the original position.

Then make a copy to check to insure that there is no more shift.
Repeat the procedures until there is no shift.
[When shifted to the rear side]
To adjust the print line in the direction B from the paper center as
shown in the figure:
1)

Loosen the red fixing screws (2 pcs. for each) of the front/back
size guide adjustment plate, and slide the side guide adjust-
ment plate in the direction B (F side) by the shift dimension.
Tighten the red fixing screws (2 pcs. for each), and slightly
push the paper feed tray into the machine. Return the stopper
to the original position, and fix it with the fixing screw (1 pc.).
Slide the auxiliary guide in the direction of B by the same
dimension.
At that time, check that the stopper pawl is engaged with the
stopper receiver of the large capacity tray.

2)

Push the large capacity tray slowly into the original position.

Then make a copy to check to insure that there is no more shift.
Repeat the procedures until there is no shift.

A

R side

F side

B

R side

F side

MX-7000N  MX-LCX2  2 – 9

2)

Loosen the stopper fixing screw (1 pc.) on the lower right side
of the paper feed tray to disable the stopper function.

3)

Then pull out the paper feed tray again until it stops.

[When shifted to the front side]
To adjust the print line in the direction A from the paper center as
shown in the figure:
1)

Loosen the red fixing screws (2 pcs. for each) of the front/back
size guide adjustment plate, and slide the side guide adjust-
ment plate in the direction A (R side) by the shift dimension.
Tighten the red fixing screws (2 pcs. for each). Slide the auxil-
iary guide in the direction of A by the same dimension.

Slightly push the paper feed tray into the machine. Return the
stopper to the original position, and fix it with the fixing screw
(1 pc.). 
At that time, check that the stopper pawl is engaged with the
stopper receiver of the large capacity tray.

2)

Push the large capacity tray slowly into the original position.

Then make a copy to check to insure that there is no more shift.
Repeat the procedures until there is no shift.
[When shifted to the rear side]
To adjust the print line in the direction B from the paper center as
shown in the figure:
1)

Loosen the red fixing screws (2 pcs. for each) of the front/back
size guide adjustment plate, and slide the side guide adjust-
ment plate in the direction B (F side) by the shift dimension.
Tighten the red fixing screws (2 pcs. for each), and slightly
push the paper feed tray into the machine. Return the stopper
to the original position, and fix it with the fixing screw (1 pc.).
Slide the auxiliary guide in the direction of B by the same
dimension.
At that time, check that the stopper pawl is engaged with the
stopper receiver of the large capacity tray.

2)

Push the large capacity tray slowly into the original position.

Then make a copy to check to insure that there is no more shift.
Repeat the procedures until there is no shift.

A

R side

F side

B

R side

F side

MX-7000N  MX-LCX2  2 – 9

2)

Loosen the stopper fixing screw (1 pc.) on the lower right side
of the paper feed tray to disable the stopper function.

3)

Then pull out the paper feed tray again until it stops.

[When shifted to the front side]
To adjust the print line in the direction A from the paper center as
shown in the figure:
1)

Loosen the red fixing screws (2 pcs. for each) of the front/back
size guide adjustment plate, and slide the side guide adjust-
ment plate in the direction A (R side) by the shift dimension.
Tighten the red fixing screws (2 pcs. for each). Slide the auxil-
iary guide in the direction of A by the same dimension.

Slightly push the paper feed tray into the machine. Return the
stopper to the original position, and fix it with the fixing screw
(1 pc.). 
At that time, check that the stopper pawl is engaged with the
stopper receiver of the large capacity tray.

2)

Push the large capacity tray slowly into the original position.

Then make a copy to check to insure that there is no more shift.
Repeat the procedures until there is no shift.
[When shifted to the rear side]
To adjust the print line in the direction B from the paper center as
shown in the figure:
1)

Loosen the red fixing screws (2 pcs. for each) of the front/back
size guide adjustment plate, and slide the side guide adjust-
ment plate in the direction B (F side) by the shift dimension.
Tighten the red fixing screws (2 pcs. for each), and slightly
push the paper feed tray into the machine. Return the stopper
to the original position, and fix it with the fixing screw (1 pc.).
Slide the auxiliary guide in the direction of B by the same
dimension.
At that time, check that the stopper pawl is engaged with the
stopper receiver of the large capacity tray.

2)

Push the large capacity tray slowly into the original position.

Then make a copy to check to insure that there is no more shift.
Repeat the procedures until there is no shift.

A

R side

F side

B

R side

F side