DOWNLOAD Sharp MX-5500N / MX-6200N / MX-7000N (serv.man32) Service Manual ↓ Size: 1.84 MB | Pages: 9 in PDF or view online for FREE

Model
MX-5500N MX-6200N MX-7000N (serv.man32)
Pages
9
Size
1.84 MB
Type
PDF
Document
Peripheral
Brand
Device
Copying Equipment / MX-LCX2 LCT A4-Installation Manual
File
mx-5500n-mx-6200n-mx-7000n-sm32.pdf
Date

Sharp MX-5500N / MX-6200N / MX-7000N (serv.man32) Peripheral ▷ View online

MX-7000N  MX-LCX2  2 – 5
<<How to separate the large capacity tray from the main
unit>>
1)
Turn the lock release screw of the front cover clockwise and
tighten the screw securely to release lock.
2)
Then hold the grips of the front and the rear cabinets with both
hands, and lift the left side. The large capacity tray will come
off.
D. Adjust the caster
1)
After installing the large capacity tray to the main unit, loosen
the screws (one in the front and one in the rear) of the adjust-
ment caster mounting plate attached to the lower side of the
large capacity tray.
At that time, the casters of the adjustment caster mounting
plate are brought into contact with the floor by the spring force.
2)
Tighten the screws (one in the front and one in the rear) of the
caster mounting plate which were loosened in procedure 1).
E. Connector connection
1)
Remove the fixing screws (one for each) from the connector
cover on the main unit and then remove the two connector
covers.
2)
Connect the large capacity tray interface harness connector
(a) and the heating heater interface harness connector (b) to
the main unit connector, and tighten the connector screw to fix
the connector.
F. Paper size switch
(1) Paper size switch from A4 to LT
Since the factory setting of the paper size is A4, if paper size switch
is required, perform the following procedures.
1)
Pull out the large capacity tray until it stops.
F side
R side
a
b
MX-7000N  MX-LCX2  2 – 6
2)
Loosen the stopper fixing screw (1 pc.) on the lower right side
of the paper feed tray to disable the stopper function.
3)
Then pull out the paper feed tray again until it stops.
a. Side plate size switch
1)
Remove the four fixing screws (blue) which are fixing the
upper and the lower sections of the side plate F and the side
plate R.
2)
Then fit the paper feed tray on the lower side of the side plate
F and the side plate R with the engraved marks of the side
plates according to the size, and insert it. Also fit the upper
side to the size and fix it with the four fixing screws (blue) that
have been removed in step 1).
b. Auxiliary guide size switch
1)
When changing the size of the side plate R, check to confirm
the mark positions of "
" on the side plate R and the size
guide adjustment plate.
2)
Loosen the fixing screw (flat screw 1pc.) of the auxiliary guide.
3)
Change the mark position (
) of the auxiliary guide and the
cassette R from A4 to LT, and fix them with the fixing screw
(flat screw, 1pc.). 
At that time, adjust so that the mark positions (
) on the
auxiliary guide and the cassette R are at the same positions of
the mark positions (
) of the side plate R and the size guide
adjustment plate checked in the procedure 1).
(If the scale of the size guide adjustment plate is at the center,
set it to the center. If the size guide adjustment plate is in 1mm
in the front side, set it in 1mm in the front side.)
c. Rear edge shaft switch
1)
Remove the rear edge shaft fixing screw (blue) on the right
side of the paper feed tray, and remove the rear edge shaft.
F side
R side
F side
R side
A4
LT
MX-7000N  MX-LCX2  2 – 7
2)
Tighten the removed rear edge shaft with the fixing screw
(blue), and store it in the storage space inside the front cabi-
net.
3)
Push the paper feed tray slightly, and return the disabled stop-
per to the original position, and fix with the fixing screw (1pc.).
At that time, check to insure that the stopper pawl is engaged
with the stopper reception of the large capacity tray unit.
4)
Push the large capacity tray slowly into the original position.
G. Turn ON the main power switch of the main 
unit
1)
Connect the  power plug of the main unit into the power outlet.
2)
Open the front cabinet of the main unit. Turn ON the power
switch in the front cabinet.
3)
Turn ON the power switch on the operation panel.
"ON"
ON
ON
MX-7000N  MX-LCX2  2 – 8
H. Size setting
Execute SIM 26-2 "Size setting" with the key operations of the main
unit.
1)
The size selection menu of the large capacity tray is displayed
on the operation message display.
2)
Select the number (Size to set) on the message screen, and
input the key.
I. Carry out the print off-center adjustment
(1) Adjustment with the simulation
Since the off-center adjustment has been made at shipping, there
is normally no need to adjust. However, if the center is shifted,
carry out the following steps to adjust.
1)
Set a test chart (document) on the document table properly.
2)
Execute SIM 50-10 (Print off center) by the key operation of
the main unit.
3)
In SIM 50-10, the display is shown as follows to allow setting of
the print off-center adjustment value for each paper feed tray.
[When shifted to the front side]
To adjust the print line in the direction A from the paper center as
shown in the figure, increment the number of value. Then make a
copy to check to insure that there is no more shift. Repeat the pro-
cedures until there is no shift.
[When shifted to the rear side]
To adjust the print line in the direction B from the paper center as
shown in the figure, decrement the number of value.
Then make a copy to check to insure that there is no more shift.
Repeat the procedures until there is no shift.
* For details of the adjustment and checking procedures, refer to
the "[6] ADJUSTMENT" on the Service Manual for main unit.
(2) Mechanical adjustment
Since the off-center adjustment is performed when shipping, there
is basically no need to perform this adjustment. If the center is
shifted, however, the simulation is normally used. If the shift is not
removed, perform the following adjustment procedure
1)
Pull out the large capacity tray gently until it stops.
Item
Default
A
BK-MAG
Main scan print magnification ratio BK
100
B
MFT
Print off-center adjustment value (Manual 
paper feed)
50
C CS1
Print off-center adjustment value (Tray 1)
50
D CS2
Print off-center adjustment value (Tray 2)
50
E
CS3
Print off-center adjustment value (Tray 3)
50
F
CS4
Print off-center adjustment value (Tray 4)
50
G LCC
Print off-center adjustment value 
(LCC)
50
H ADU
Print off-center adjustment value (ADU)
50
I
MULTI COUNT
Number of print
1
J
PAPER
MFT
Tray selection
1 : Manual paper feed
2
CS 1
2 : Tray 1
CS 2
3 : Tray 2
CS 3
4 : Tray 3
CS 4
5 : Tray 4
LCC
6 : LCC
K
DUPLEX
YES
Duplex 
selection
0 : Selection
1
NO
1 : Unselection
R side
Center line of image (first image
ȫ
F side
(Fig. 1)
Direction A
R side
Center line of image (first image
ȫ
F side
(fig. 2)
Direction B
Page of 9
Display

Click on the first or last page to see other MX-5500N / MX-6200N / MX-7000N (serv.man32) service manuals if exist.