DOWNLOAD Sharp MX-5500N / MX-6200N / MX-7000N (serv.man32) Service Manual ↓ Size: 1.84 MB | Pages: 9 in PDF or view online for FREE

MX-7000N  MX-LCX2  2 – 3

3)

Release the lock, and open the right door.

4)

Remove the screws, and remove the upper cover.

5)

Close the right door.

6)

Remove the fixing screws (2 pcs.) of the machine entry port,
and remove the entry port cover.

7)

Attach the entry port cover reversely to the machine and fix it
with the two fixing screws which was removed in procedure 3).
* When working, be careful to prevent damage of the paper

pass (transport) surface on the entry port cover.

8)

Release the lock, and open the right door.

9)

Install the upper cover, and fix with the screws.

MX-7000N  MX-LCX2  2 – 4

10) Close the right door.

1)

Hold the grips of the front and the rear cabinets with both
hands, and lift the left side.

2)

Hang the metal fixture of the large capacity tray on the lower
front/rear connecting plate of the main unit side. Push the large
capacity tray onto the main unit and attach it.

At that time, pull the large capacity tray in a right direction and
check that a large capacity tray is locked to the main body.

* If lock is incomplete, when the power switch is turned on, the

message, “Check installation of tray 5” is displayed on the
operation panel.

* Push the large capacity tray onto the machine, and lock it

securely.

Note 1)
When lifting the LCC, insert fingers firmly into the grip sections of
the front and rear cabinets and install slowly.

Note 2)
Turn the lock release screw of the front cover counterclockwise to
loosen and check that the screw is free.

* If the screw is tight at that time, installation will be incomplete.

R

F

MX-7000N  MX-LCX2  2 – 5

<<How to separate the large capacity tray from the main
unit>>
1)

Turn the lock release screw of the front cover clockwise and
tighten the screw securely to release lock.

2)

Then hold the grips of the front and the rear cabinets with both
hands, and lift the left side. The large capacity tray will come
off.

1)

After installing the large capacity tray to the main unit, loosen
the screws (one in the front and one in the rear) of the adjust-
ment caster mounting plate attached to the lower side of the
large capacity tray.
At that time, the casters of the adjustment caster mounting
plate are brought into contact with the floor by the spring force.

2)

Tighten the screws (one in the front and one in the rear) of the
caster mounting plate which were loosened in procedure 1).

1)

Remove the fixing screws (one for each) from the connector
cover on the main unit and then remove the two connector
covers.

2)

Connect the large capacity tray interface harness connector
(a) and the heating heater interface harness connector (b) to
the main unit connector, and tighten the connector screw to fix
the connector.

Since the factory setting of the paper size is A4, if paper size switch
is required, perform the following procedures.
1)

Pull out the large capacity tray until it stops.

F side

R side

a

b

MX-7000N  MX-LCX2  2 – 6

2)

Loosen the stopper fixing screw (1 pc.) on the lower right side
of the paper feed tray to disable the stopper function.

3)

Then pull out the paper feed tray again until it stops.

a. Side plate size switch
1)

Remove the four fixing screws (blue) which are fixing the
upper and the lower sections of the side plate F and the side
plate R.

2)

Then fit the paper feed tray on the lower side of the side plate
F and the side plate R with the engraved marks of the side
plates according to the size, and insert it. Also fit the upper
side to the size and fix it with the four fixing screws (blue) that
have been removed in step 1).

b. Auxiliary guide size switch
1)

When changing the size of the side plate R, check to confirm
the mark positions of "

" on the side plate R and the size

guide adjustment plate.

2)

Loosen the fixing screw (flat screw 1pc.) of the auxiliary guide.

3)

Change the mark position (

) of the auxiliary guide and the

cassette R from A4 to LT, and fix them with the fixing screw
(flat screw, 1pc.). 

At that time, adjust so that the mark positions (

) on the

auxiliary guide and the cassette R are at the same positions of
the mark positions (

) of the side plate R and the size guide

adjustment plate checked in the procedure 1).
(If the scale of the size guide adjustment plate is at the center,
set it to the center. If the size guide adjustment plate is in 1mm
in the front side, set it in 1mm in the front side.)

c. Rear edge shaft switch
1)

Remove the rear edge shaft fixing screw (blue) on the right
side of the paper feed tray, and remove the rear edge shaft.

F side

R side

F side

R side

A4

LT