DOWNLOAD Sharp MX-5500N / MX-6200N / MX-7000N (serv.man31) Service Manual ↓ Size: 3.06 MB | Pages: 10 in PDF or view online for FREE

MX-7000N  MX-CFX1  5 – 4

4)

Close the front cover of the finisher (or Punch unit).

5)

Remove the screws on rear side of the finisher (or Punch unit),
and remove the rear cover.

6)

Attach the fixing screw (Package part No. 4 of MX-FNX3 or
MX-FNX4).

7)

Install the rear cover of the finisher (or Punch unit) with the fix-
ing screws.

1)

Install the latch reception parts (Package part No. 8) to the
main unit with the fixing screws (Package part No. 1).

2)

Install the positioning pin (Package part No. 9) to the main unit
with the fixing screws (Package part No. 3).

* Be careful to the direction of the installation.

MX-7000N  MX-CFX1  5 – 5

1)

Engage the inserter that has installed finisher (Punch unit) to
the main unit.

2)

Release the lock, and remove the inserter from the main unit.

3)

Fix the rail (Package part No. 5) to the main unit side with the
fixing screws (Package part No. 2).

4)

Fix the rail to inserter with the fixing screws (Package part No.
1).

1)

Put the inserter that has installed the finisher (Punch unit)
close to the main unit.

2)

Check that the positioning pin of main unit is smoothly installed
to center of the guide for inserter positioning.

* When the positioning pin enters smoothly, progress to the

procedure of "G. Height adjustment of the finisher and the
inserter". 
When the positioning pin not enters smoothly, progress to
the following procedures.

3)

Loosen the fixing screws of the adjustment section on the rear
side of the inserter.

MX-7000N  MX-CFX1  5 – 6

4)

Turn the height adjustment bolt on the rear side so that the
height of the center of the positioning pin and the center of the
positioning guide is fit.

5)

Tighten the fixing screws of the adjustment section on the rear
side.

6)

Remove the screw, and open the rack cover.

7)

Loosen the fixing screws of the adjustment section on the front
side.

8)

Turn the height adjustment screws on the front side so that the
fixing screw of the adjustment section on the front side may
become the same position as a rear side. 

9)

Tighten the fixing screws of the adjustment section on the front
side.

10) Close the rack cover, and fix with the screw.

1)

Check the height of front cabinet of the inserter and front cabi-
net of the finisher.

Front

MX-7000N  MX-CFX1  5 – 7

2)

Check the height of rear cabinet of the inserter and rear cabi-
net of the finisher.

* When the height is properly adjusted, progress to the proce-

dure of "H. Check the clearance of the main unit and the
inserter". 
When the height is not properly adjusted, progress to the fol-
lowing procedures.
<Adjust of the height on front side>

3)

Remove each cabinet of the finisher, and loosen the front
caster fixing screws on the inserter side.
* The adjustment procedure is different according to the

installed finisher. For details, refer to the adjustment proce-
dure of each finisher.

4)

Turn the height adjustment bolt so that the upper cabinet may
become equal height.

5)

Tighten the caster fixing screws.

6)

Remove the rear cabinet of the finisher, and loosen the rear
caster fixing screws on the inserter side.

7)

Turn the height adjustment bolt so that the upper cabinet may
become equal height.

8)

Tighten the caster fixing screws.

Rear