DOWNLOAD Sharp MX-5500N / MX-6200N / MX-7000N (serv.man30) Service Manual ↓ Size: 2.09 MB | Pages: 6 in PDF or view online for FREE

MX-7000N  MX-PNX2A/B/C/D  6 – 4

2)

Install the Connection fixture R (Package part No. 8) to the
main unit with the fixing screws (Package part No. 4).

1)

Engage the finisher that has installed punch unit to the main
unit, and temporarily fix.
* Insert the rail of the finisher unit into the rail reception fixture

of main unit, fix temporarily.

2)

Open the front door of punch unit.

3)

Check that the center of the screw hole of the punch unit is in
the range of specification of an oval hole of the mounting fix-
ture  in front side of main unit.

* When not the range of specification, execute the adjustment

procedure of each finisher. If the adjustment is not required,
execute the procedure for touch of the auxiliary caster with
the floor of each finisher.

* Refer to the adjustment procedure of each finisher.

* Refer to the procedure for touch of the auxiliary caster with the

floor of each finisher.

1)

Engage the finisher that has installed punch unit to the main
unit.

2)

Open the front door of punch unit.

MX-7000N  MX-PNX2A/B/C/D  6 – 5

3)

Fix the main unit and the punch unit with the fixing screw
(Package part No. 4 of MX-FNX3 or MX-FNX4).

4)

Close the front door of punch unit.

5)

Install the fixing screw (Package part No. 4 of MX-FNX3 or
MX-FNX4) on rear side.

6)

Install the rear cover of punch unit with the fixing screws.

7)

By using nippers, split the removed connector cover of the fin-
isher along the perforated line.

8)

Install the connector cover of the finisher and fix it with the fix-
ing screw.

1)

Connect two connectors of the finisher to the main unit, and
tighten the screws.

MX-7000N  MX-PNX2A/B/C/D  6 – 6

1)

Attach the punch position label to the position indicated in the
figure.
[For scanner] (Package part No. 11 of MX-FNX3 or MX-FNX4)

[For DSPF] (Package part No. 12 of MX-FNX3 or MX-FNX4)

1)

Connect the power plug of the main unit into the power outlet.

2)

Open the front cabinet of the main unit. Turn ON the power
switch in the front cabinet.

3)

Turn ON the power switch on the operation panel.

Edge of R part in corner

Second label

Lose the clearance.

First label

Edge of R part in corner

* The corner of the upper

cabinet rear part

Reference line of
sticking label on.

edge R2.5

Tangential line

of R2.5

MX-7000N  MX-PNX2A/B/C/D  6 – 6

1)

Attach the punch position label to the position indicated in the
figure.
[For scanner] (Package part No. 11 of MX-FNX3 or MX-FNX4)

[For DSPF] (Package part No. 12 of MX-FNX3 or MX-FNX4)

1)

Connect the power plug of the main unit into the power outlet.

2)

Open the front cabinet of the main unit. Turn ON the power
switch in the front cabinet.

3)

Turn ON the power switch on the operation panel.

Edge of R part in corner

Second label

Lose the clearance.

First label

Edge of R part in corner

* The corner of the upper

cabinet rear part

Reference line of
sticking label on.

edge R2.5

Tangential line

of R2.5