Sharp MX-5500N / MX-6200N / MX-7000N (serv.man26) Peripheral ▷ View online
MX-PEX2 Installation in MX-5500N/6200N/7000N 3 – 2
3. Install of the I/F unit
1)
Remove the three screws of the MFP cnt PWB. Install the I/F
unit (package part No.1) with the three screws that was
detached from MFP cnt PWB.
* When installing the I/F unit, use an extreme care to make
unit (package part No.1) with the three screws that was
detached from MFP cnt PWB.
* When installing the I/F unit, use an extreme care to make
the sheet metal not come in contact with the MFP cnt PWB.
4. Installation of the control box
1)
Insert the control box until the connectable position for HDD-
IDE cable, connect the HDD-IDE cable.
IDE cable, connect the HDD-IDE cable.
2)
Insert the control box until the position that fix the HDD-IDE
cable to the clamp, put the HDD-IDE cable to the sheet (A),
and fix it to the clamp.
* Check that the HDD-IDE cable is not twisting, hanging
cable to the clamp, put the HDD-IDE cable to the sheet (A),
and fix it to the clamp.
* Check that the HDD-IDE cable is not twisting, hanging
down, etc.
3)
Push the control box into the main unit. Lay the finger handle.
Fix with the screws.
Fix with the screws.
4)
Cut out the cut-out portion of the right rear cabinet.
5)
Push into the cable to the right cabinet rear cover, and attach
it. At this time, check that the pawls are properly fitted to the
main unit.
it. At this time, check that the pawls are properly fitted to the
main unit.
1
2
3
1
2
1
A
2
3
1
2
2
3
3
2
4
5
2
3
1
MX-PEX2 Installation in MX-5500N/6200N/7000N 3 – 3
5. Installation of the printer controller
1)
Remove the four screws from the rear cabinet. Attach two step
screws (package part No. 2) to the two positions in four posi-
tions where the fixing screws have been removed.
screws (package part No. 2) to the two positions in four posi-
tions where the fixing screws have been removed.
2)
Engage the printer controller unit with the step screws, and
slide it to the right door side.
slide it to the right door side.
3)
Fix the print controller unit using the two screws of the four
screws removed in step 1.
screws removed in step 1.
4)
Connect the cable (A) of the I/F unit, the LAN cable (package
part No. 3), and the AC power cord (C) (package part No. 4).
part No. 3), and the AC power cord (C) (package part No. 4).
6. Caution label attachment
1)
Attach the caution label (package part No. 5) near a AC power
cord inlet of the main unit.
cord inlet of the main unit.
7. Turn ON the power switch of the print
controller unit and main unit
1)
Insert the power plug of the print controller unit into the power
outlet.
outlet.
1
1
1
1
2
1
2
2
A
B
C
MX-PEX2 Installation in MX-5500N/6200N/7000N 3 – 4
2)
Insert the power plug of the main unit into the power outlet.
3)
Turn ON the power switch of the print controller unit.
4)
Open the front cabinet. Turn ON the power switch in the front
cabinet of the main unit.
cabinet of the main unit.
5)
Turn ON the power switch on the operation panel.
8. Note for network setting and
calibration resetting
CAUTION: After the MX-PEX2 is installed, be sure the setting
of items as follows again.
(Reconfiguration in setting is required, because the
information that had been keeping before installa-
tion is initialized.)
(Reconfiguration in setting is required, because the
information that had been keeping before installa-
tion is initialized.)
1)
System setting
→ Printer Setting (administrator area) → Fiery
Setting
→ Carry out the initial setting from Fiery menu.
2)
After the initial setting and automatic reboot
→ Printer Setting
(administrator area)
→ Fiery Setting → Carry out the calibra-
tion from Fiery menu again.
A. About the Fiery Setting
Refer to the configuration manual "SETTING UP THE FIERY
X3ETY2 FROM THE COPIER TOUCH PANEL".
X3ETY2 FROM THE COPIER TOUCH PANEL".
B. About the calibration
Refer to the color printing manual "Calibration".
1)
1)
To execute the calibration from the touch panel of Copier, refer
to the "Calibrating from the Fiery X3eTY2 copier touch panel".
to the "Calibrating from the Fiery X3eTY2 copier touch panel".
2)
To execute the calibration with a color measurement meter,
refer to the "Calibrating with ColorWise Pro Tools Calibrator".
refer to the "Calibrating with ColorWise Pro Tools Calibrator".
ON
"ON"
ON
ON
CAUTION:
No part of this publication may be reproduced,
stored in a retrieval system, or transmitted in
any form or by any means, electronic, mechanical,
photocopying, recording, or otherwise, without
prior written permission of the publisher.
stored in a retrieval system, or transmitted in
any form or by any means, electronic, mechanical,
photocopying, recording, or otherwise, without
prior written permission of the publisher.
COPYRIGHT
©
XXXX BYSHARP CORPORATION
ALL RIGHTS RESERVED.
The PWB’s of this model employs lead-free solder. The “LF” marks indicated on the PWB’s and the Service Manual mean “Lead-Free” solder.
The alphabet following the LF mark shows the kind of lead-free solder.
(1) NOTE FOR THE USE OF LEAD-FREE SOLDER THREAD
When repairing a lead-free solder PWB, use lead-free solder thread.
Never use conventional lead solder thread, which may cause a breakdown or an accident.
Since the melting point of lead-free solder thread is about 40°C higher than that of conventional lead solder thread, the use of the
exclusive-use soldering iron is recommendable.
exclusive-use soldering iron is recommendable.
(2) NOTE FOR SOLDERING WORK
Since the melting point of lead-free solder is about 220°C, which is about 40°C higher than that of conventional lead solder, and its soldering
capacity is inferior to conventional one, it is apt to keep the soldering iron in contact with the PWB for longer time. This may cause land
separation or may exceed the heat-resistive temperature of components. Use enough care to separate the soldering iron from the PWB when
completion of soldering is confirmed.
capacity is inferior to conventional one, it is apt to keep the soldering iron in contact with the PWB for longer time. This may cause land
separation or may exceed the heat-resistive temperature of components. Use enough care to separate the soldering iron from the PWB when
completion of soldering is confirmed.
Since lead-free solder includes a greater quantity of tin, the iron tip may corrode easily. Turn ON/OFF the soldering iron power frequently.
If different-kind solder remains on the soldering iron tip, it is melted together with lead-free solder. To avoid this, clean the soldering iron
tip after completion of soldering work.
tip after completion of soldering work.
If the soldering iron tip is discolored black during soldering work, clean and file the tip with steel wool or a fine filer.
Example:
5mm
Lead-Free
Solder composition
code (Refer to the
table at the right.)
code (Refer to the
table at the right.)
<Solder composition code of lead-free solder>
Solder composition
Sn-Ag-Cu
Sn-Ag-Bi
Sn-Ag-Bi-Cu
Sn-Ag-Bi-Cu
Sn-Zn-Bi
Sn-In-Ag-Bi
Sn-Cu-Ni
Sn-Ag-Sb
Bi-Sn-Ag-P
Bi-Sn-Ag
Bi-Sn-Ag
a
b
z
i
n
s
p
Solder composition code
a
LEAD-FREE SOLDER
Click on the first or last page to see other MX-5500N / MX-6200N / MX-7000N (serv.man26) service manuals if exist.