Sharp MX-5500N / MX-6200N / MX-7000N (serv.man26) Peripheral ▷ View online
MX-PEX2 Installation in MX-5500N/6200N/7000N 3 – 1
MX-PEX2
Service Manual
[3] Installation in MX-5500N/
6200N/7000N
<Note before installation>
* Start installation after checking that the LINE indicator and the
* Start installation after checking that the LINE indicator and the
DATA indicator below it on the operation panel are neither lit nor
blinking.
blinking.
1. Turn OFF the power of the main unit
1)
Turn the power switch located on the operation panel to the
"OFF" position.
"OFF" position.
2)
After checking that the operation panel has gone out, open the
front cabinet and turn the main power switch to the “OFF” posi-
tion.
front cabinet and turn the main power switch to the “OFF” posi-
tion.
3)
Disconnect the power plug of the main unit from the power out-
let.
let.
2. Removal of the control box
1)
Remove the screw of right rear cabinet, push down the right
rear cabinet. Disengage the pawls, and remove the right rear
cabinet so that slide to the front side.
rear cabinet. Disengage the pawls, and remove the right rear
cabinet so that slide to the front side.
2)
Remove the screws of control box. Raise the finger handle,
and pull out the control box slowly.
and pull out the control box slowly.
3)
Pull out the control box until the position in which the clamp is
seen. Remove the HDD-IDE cable from the clamp.
seen. Remove the HDD-IDE cable from the clamp.
4)
Pull out the control box until the position in which the connector
of the HDD-IDE cable is seen. Pull the sheet, and remove the
HDD-IDE cable.
of the HDD-IDE cable is seen. Pull the sheet, and remove the
HDD-IDE cable.
"OFF"
"OFF"
"OFF"
3
4
1
2
1
1
2
2
3
1
2
1
2
MX-PEX2 Installation in MX-5500N/6200N/7000N 3 – 2
3. Install of the I/F unit
1)
Remove the three screws of the MFP cnt PWB. Install the I/F
unit (package part No.1) with the three screws that was
detached from MFP cnt PWB.
* When installing the I/F unit, use an extreme care to make
unit (package part No.1) with the three screws that was
detached from MFP cnt PWB.
* When installing the I/F unit, use an extreme care to make
the sheet metal not come in contact with the MFP cnt PWB.
4. Installation of the control box
1)
Insert the control box until the connectable position for HDD-
IDE cable, connect the HDD-IDE cable.
IDE cable, connect the HDD-IDE cable.
2)
Insert the control box until the position that fix the HDD-IDE
cable to the clamp, put the HDD-IDE cable to the sheet (A),
and fix it to the clamp.
* Check that the HDD-IDE cable is not twisting, hanging
cable to the clamp, put the HDD-IDE cable to the sheet (A),
and fix it to the clamp.
* Check that the HDD-IDE cable is not twisting, hanging
down, etc.
3)
Push the control box into the main unit. Lay the finger handle.
Fix with the screws.
Fix with the screws.
4)
Cut out the cut-out portion of the right rear cabinet.
5)
Push into the cable to the right cabinet rear cover, and attach
it. At this time, check that the pawls are properly fitted to the
main unit.
it. At this time, check that the pawls are properly fitted to the
main unit.
1
2
3
1
2
1
A
2
3
1
2
2
3
3
2
4
5
2
3
1
MX-PEX2 Installation in MX-5500N/6200N/7000N 3 – 3
5. Installation of the printer controller
1)
Remove the four screws from the rear cabinet. Attach two step
screws (package part No. 2) to the two positions in four posi-
tions where the fixing screws have been removed.
screws (package part No. 2) to the two positions in four posi-
tions where the fixing screws have been removed.
2)
Engage the printer controller unit with the step screws, and
slide it to the right door side.
slide it to the right door side.
3)
Fix the print controller unit using the two screws of the four
screws removed in step 1.
screws removed in step 1.
4)
Connect the cable (A) of the I/F unit, the LAN cable (package
part No. 3), and the AC power cord (C) (package part No. 4).
part No. 3), and the AC power cord (C) (package part No. 4).
6. Caution label attachment
1)
Attach the caution label (package part No. 5) near a AC power
cord inlet of the main unit.
cord inlet of the main unit.
7. Turn ON the power switch of the print
controller unit and main unit
1)
Insert the power plug of the print controller unit into the power
outlet.
outlet.
1
1
1
1
2
1
2
2
A
B
C
MX-PEX2 Installation in MX-5500N/6200N/7000N 3 – 4
2)
Insert the power plug of the main unit into the power outlet.
3)
Turn ON the power switch of the print controller unit.
4)
Open the front cabinet. Turn ON the power switch in the front
cabinet of the main unit.
cabinet of the main unit.
5)
Turn ON the power switch on the operation panel.
8. Note for network setting and
calibration resetting
CAUTION: After the MX-PEX2 is installed, be sure the setting
of items as follows again.
(Reconfiguration in setting is required, because the
information that had been keeping before installa-
tion is initialized.)
(Reconfiguration in setting is required, because the
information that had been keeping before installa-
tion is initialized.)
1)
System setting
→ Printer Setting (administrator area) → Fiery
Setting
→ Carry out the initial setting from Fiery menu.
2)
After the initial setting and automatic reboot
→ Printer Setting
(administrator area)
→ Fiery Setting → Carry out the calibra-
tion from Fiery menu again.
A. About the Fiery Setting
Refer to the configuration manual "SETTING UP THE FIERY
X3ETY2 FROM THE COPIER TOUCH PANEL".
X3ETY2 FROM THE COPIER TOUCH PANEL".
B. About the calibration
Refer to the color printing manual "Calibration".
1)
1)
To execute the calibration from the touch panel of Copier, refer
to the "Calibrating from the Fiery X3eTY2 copier touch panel".
to the "Calibrating from the Fiery X3eTY2 copier touch panel".
2)
To execute the calibration with a color measurement meter,
refer to the "Calibrating with ColorWise Pro Tools Calibrator".
refer to the "Calibrating with ColorWise Pro Tools Calibrator".
ON
"ON"
ON
ON
CAUTION:
Click on the first or last page to see other MX-5500N / MX-6200N / MX-7000N (serv.man26) service manuals if exist.