DOWNLOAD Sharp MX-5500N / MX-6200N / MX-7000N (serv.man26) Service Manual ↓ Size: 2.19 MB | Pages: 12 in PDF or view online for FREE

MX-PEX2  Configuration  1 – 1

MX-PEX2

Service Manual

 

1)

Remove the print controller unit.

1)

Check that all the items are included in the package.

The MFP model is detected when the power is turned on for the first time after the shipment from the factory, and the system that matches the
MFP (MX-5500N/6200N/7000N or MX-3500/4500 series) is started.
After the system is started, the initial setup screen is displayed.
After the completion of the setup, the detection of MFP model at the boot-up will not be executed.
It is necessary to return the controller to the default state if you want to re-connect it to another MFP after the setup.
System setting 

→ Printer Setting (administrator area) → Fiery Setting → Run Setup

Password: Fiery.1 (Default) 

→ Factory Default

NOTE: Please make sure to reset to the default state if you connect the controller to another model, because the controller starts

NOTE: MX-PEX1 was shipped after setting the basic setting (the information of MFP) by default, but MX-PEX2 is shipped in the fac-

MX-3500/4500 series

YES

YES

MX-5500N/6200N/7000N

NO

YES

1

I/F unit

1

2

Step screw

2

3

LAN cable (cross cable)

1

4

AC power cable

1

5

Caution label

1

6

CD-ROM

7

7

Quick guide

1

8

Release notes

1

9

KODAK chart

1

1

4

2

3

6

7

8

5

9

MX-PEX2  Installation in MX-3500/4500 series  2 – 1

MX-PEX2

Service Manual

 

<Note before installation>
* Start installation after checking that the LINE indicator and the

DATA indicator below it on the operation panel are neither lit nor
blinking.

1)

Turn the power switch located on the operation panel to the
"OFF" position.

2)

After checking that the operation panel has gone out, open the
front cabinet and turn the main power switch to the “OFF” opsi-
tion.

3)

Remove the power plug of the main unit from the outlet.

1)

Remove the ozone filter cover. Remove the screws, and
remove the right rear cabinet cover.

2)

Remove the screws, and pull out the MFP cnt PWB unit.

3)

Remove the three screws of the MFP cnt PWB. Install the I/F
unit (package part No. 1) with the three screws that was
detached from MFP cnt PWB.
* When installing the I/F unit, use an extreme care to make

the sheet metal not come in contact with the MFP cnt PWB.

MX-PEX2  Installation in MX-3500/4500 series  2 – 2

4)

Restore the MFP cnt PWB unit to the main unit, and fix with the
screws.

5)

Cut out the cut-out portion of the right rear cabinet cover for
cable along the perforated line. Attach the right rear cabinet
cover, and fix with the screw. Attach the ozone filter cover.

1)

Remove the four screws from the rear cabinet. Attach two step
screws (package part No. 2) to the two positions in four posi-
tions where the fixing screws have been removed.

2)

Engage the printer controller unit with the step screws, and
slide it to the right door side.

3)

Fix the print controller unit using the two screws of the four
screws removed in step 1.

1)

Connect the cable (A) of the I/F unit, the LAN cable (package
part No. 3), and the AC power cord (C) (package part No. 4).

MX-PEX2  Installation in MX-3500/4500 series  2 – 3

1)

Attach the caution label (package part No. 5) near a AC power
cord inlet of the main unit.

1)

Insert the power plug of the print controller unit into the power
outlet.

2)

Insert the power plug of the main unit to the outlet.

3)

Turn on the power switch of the print controller unit.

4)

Open the front cabinet. Turn ON the power switch in the front
cabinet of the main unit.

5)

Turn ON the power switch on the operation panel.

CAUTION: After the MX-PEX1/PEX2 is installed, be sure the

1)

System setting 

→ Printer Setting (administrator area) → Fiery

Setting 

→ Carry out the initial setting from Fiery menu. 

2)

After the initial setting and automatic reboot 

→ Printer Setting

(administrator area) 

→ Fiery Setting → Carry out the calibra-

tion from Fiery menu again. 

Refer to the configuration manual "SETTING UP THE FIERY
X3ETY2 FROM THE COPIER TOUCH PANEL".

Refer to the color printing manual "Calibration".
1)

To execute the calibration from the touch panel of Copier, refer
to the "Calibrating from the Fiery X3eTY2 copier touch panel".

2)

To execute the calibration with a color measurement meter,
refer to the "Calibrating with ColorWise Pro Tools Calibrator".