DOWNLOAD Sharp MX-5500N / MX-6200N / MX-7000N (serv.man25) Service Manual ↓ Size: 2.87 MB | Pages: 99 in PDF or view online for FREE

 

Always observe the following general precautions when servicing the Fiery X3eTY2:

 

If there is any evidence of shipping or handling damage to packing boxes or their 
contents, save the damaged boxes and parts, call the shipper immediately to file a claim, 
and notify your authorized service/support center.

 

The Fiery X3eTY2 is probably connected to an existing Local Area Network (LAN) 
based on Ethernet hardware. The network is the link between the customer’s computer, 
existing laser printers, and other prepress equipment. Never disturb the LAN by breaking 
or making a network connection, altering termination, installing or removing 
networking hardware or software, or shutting down networked devices without the 
knowledge and express permission of the network administrator.

 

Only the network administrator should assign an IP address on a network device. 
Entering an incorrect IP address to the Fiery X3eTY2 can cause unpredictable errors on 
any or all devices.

 

Static electricity is always a concern when servicing electronic devices. It is highly 
unlikely that the area around the Fiery X3eTY2 is static-free. Carpeting, leather-soled 
shoes, synthetic clothing fibers, silks, and plastics may generate a static charge of more 
than 10,000 volts. Static discharge is capable of destroying the circuits etched in silicon 
microchips, or dramatically shortening their life span. By observing standard precautions, 
you can avoid extra service calls and save the cost of a new board.

When possible, work on a ground-connected antistatic mat. Wear an antistatic 
wristband, grounded at the same place as the antistatic mat. If that is not possible:

• Attach a grounding strap to your wrist. Attach the other end to a good ground.

• After removing an electronic component, place it into an antistatic bag immediately. 

Do not walk across a carpet or vinyl floor while carrying an unprotected board.

• Leave new electronic components inside their antistatic bags until you are ready to 

install them. 

• When you unpack the electronic components, touch a metal area of the Fiery X3eTY2 

to discharge the static on your body. Place the components on a grounded antistatic 
surface, component-side up.

 

The power supply cord is used as the main disconnect device. Ensure that the 

socket-outlet is located/installed near the equipment and is easily accessible.

 

Der Netzstecker dient zur sicheren Trennung des Gerätes von der Stromversorgung. Stellen Sie sicher, dass sich die 

Steckdose in unmittelbarer Nähe des Gerätes befindet und leicht zugänglich ist.

 

Le cordon d’alimentation doit être débranché pour une mise hors tension totale du produit. La prise de courant 

doit être située ou installée à proximité du matériel et être facilement accessible.

 

Danger of explosion if battery is replaced with incorrect type. Replace only 

with the same type recommended by the manufacturer. Dispose of used batteries 
according to the manufacturer’s instructions.

 

Es besteht Explosionsgefahr, wenn die Batterien durch einen falschen Batterientyp ersetzt werden. Ersetzen Sie sie 

deshalb nur durch denselben, vom Hersteller empfohlenen Typ. Entsorgen Sie leere Batterien entsprechend den Anweisungen 
des Herstellers.

 

IIl y a danger d’explosion en cas de remplacement avec le mauvais type de batterie. Remplacer uniquement avec 

une batterie du même type recommandé par le constructeur. Les batteries usagées doivent être jetées conformément aux 
instructions du fabricant.

 

This product relies on the building’s installation for short-circuit 

(overcurrent) protection. Ensure that a fuse or circuit breaker no larger than 120 VAC, 
15A U.S. (240 VAC, 10A international) is used on the phase conductors (all current-
carrying conductors).

 

Dieses Produkt ist darauf angewiesen, dass im Gebäude ein Kurzschluss- bzw. Überstromschutz installiert ist. 

Stellen Sie sicher, dass eine Sicherung oder ein Unterbrecher von nicht mehr als 240 V Wechselstrom, 10 A (bzw. in den USA 
120 V Wechselstrom, 15 A) an den Phasenleitern (allen stromführenden Leitern) verwendet wird.

 

La protection contre les courts-circuits (surtension) du produit est assurée par l’installation électrique du local où 

il est installé. S’assurer qu’un fusible ou un disjoncteur inférieur ou égal à 120 V CA, 15 A aux Etats-Unis (240 V CA, 10 A 
dans les autres pays) est utilisé pour les conducteurs de phase (conducteurs de courant).

 

Fiery X3eTY2 exploded view

i

The CPU cooling 

assembly shown here may differ 
from the cooling assembly 
installed in your system. For 
more information, see page 24.

 

To service the Fiery X3eTY2, you must perform the following tasks:

• Shut down the Fiery X3eTY2; power off both the Fiery X3eTY2 and the MFP.

• Remove the Fiery X3eTY2 from the MFP.

• Open the Fiery X3eTY2.

 

Before you touch any parts inside the Fiery X3eTY2, make sure to wear an 

ESD grounding wrist strap and follow all ESD safety precautions. 

 

Fiery Settings screen

 

• Press the Copy tab on the MFP touch 

panel.

• Press the Fiery icon at the bottom of 

the touch panel.

• Press Fiery Settings.

The Fiery Settings screen appears.

• Press the System Settings button on 

the MFP.

• On the touch panel, press Admin 

Password and then press Password.

• On the touch panel, use the keyboard 

to enter the administrator password for 
the MFP. Press OK and then press OK 
again at the next screen.

This password is not the same as the 
administrator password for the 
Fiery X3eTY2.

• At the System Settings screen, use the 

arrows to scroll to Printer Settings and 
press Printer Settings.

• Press Fiery Settings.

The Fiery Settings screen appears.

Server Name
Idle

##### MB              x.x

Info