Sharp MX-5500N / MX-6200N / MX-7000N (serv.man25) Peripheral ▷ View online
2
Scope of this guide
Scope of this guide
This guide does not describe how to install the Fiery X3eTY2 controller onto the MFP
or how to troubleshoot or service the MFP. For detailed information about components
inside the MFP, see the documentation provided by the MFP manufacturer.
or how to troubleshoot or service the MFP. For detailed information about components
inside the MFP, see the documentation provided by the MFP manufacturer.
Tools needed
To install or service the Fiery X3eTY2, bring the following tools and parts to the
customer site:
customer site:
• ESD wrist grounding strap and antistatic mat
• #1 and #2 Phillips head screwdrivers (non-magnetic)
• Small flat-blade screwdriver
• Needlenose pliers (to straighten bent pins)
• Windows XP or 2000 computer
For additional system requirements, see page 51.
Bring this guide, documentation for any optional service kits you are installing, and any
technical notes for the Fiery X3eTY2 to the customer site.
technical notes for the Fiery X3eTY2 to the customer site.
3
Precautions
Precautions
Always observe the following general precautions when servicing the Fiery X3eTY2:
1.
Report any shipping damage.
If there is any evidence of shipping or handling damage to packing boxes or their
contents, save the damaged boxes and parts, call the shipper immediately to file a claim,
and notify your authorized service/support center.
contents, save the damaged boxes and parts, call the shipper immediately to file a claim,
and notify your authorized service/support center.
2.
Never alter an existing network without permission.
The Fiery X3eTY2 is probably connected to an existing Local Area Network (LAN)
based on Ethernet hardware. The network is the link between the customer’s computer,
existing laser printers, and other prepress equipment. Never disturb the LAN by breaking
or making a network connection, altering termination, installing or removing
networking hardware or software, or shutting down networked devices without the
knowledge and express permission of the network administrator.
based on Ethernet hardware. The network is the link between the customer’s computer,
existing laser printers, and other prepress equipment. Never disturb the LAN by breaking
or making a network connection, altering termination, installing or removing
networking hardware or software, or shutting down networked devices without the
knowledge and express permission of the network administrator.
3.
Never assign an IP address in Network Setup.
Only the network administrator should assign an IP address on a network device.
Entering an incorrect IP address to the Fiery X3eTY2 can cause unpredictable errors on
any or all devices.
Entering an incorrect IP address to the Fiery X3eTY2 can cause unpredictable errors on
any or all devices.
4.
Follow standard ESD (electrostatic discharge) precautions while working on the internal
components of the Fiery X3eTY2.
components of the Fiery X3eTY2.
Static electricity is always a concern when servicing electronic devices. It is highly
unlikely that the area around the Fiery X3eTY2 is static-free. Carpeting, leather-soled
shoes, synthetic clothing fibers, silks, and plastics may generate a static charge of more
than 10,000 volts. Static discharge is capable of destroying the circuits etched in silicon
microchips, or dramatically shortening their life span. By observing standard precautions,
you can avoid extra service calls and save the cost of a new board.
unlikely that the area around the Fiery X3eTY2 is static-free. Carpeting, leather-soled
shoes, synthetic clothing fibers, silks, and plastics may generate a static charge of more
than 10,000 volts. Static discharge is capable of destroying the circuits etched in silicon
microchips, or dramatically shortening their life span. By observing standard precautions,
you can avoid extra service calls and save the cost of a new board.
When possible, work on a ground-connected antistatic mat. Wear an antistatic
wristband, grounded at the same place as the antistatic mat. If that is not possible:
wristband, grounded at the same place as the antistatic mat. If that is not possible:
• Attach a grounding strap to your wrist. Attach the other end to a good ground.
• After removing an electronic component, place it into an antistatic bag immediately.
Do not walk across a carpet or vinyl floor while carrying an unprotected board.
• Leave new electronic components inside their antistatic bags until you are ready to
install them.
• When you unpack the electronic components, touch a metal area of the Fiery X3eTY2
to discharge the static on your body. Place the components on a grounded antistatic
surface, component-side up.
surface, component-side up.
5.
Avoid flexing a printed circuit board, and handle it by opposing edges (not corners) only.
6.
Never set a cup of coffee—or any liquid—on or near any components or the MFP.
4
Precautions
Power Supply Cord Notice
CAUTION:
The power supply cord is used as the main disconnect device. Ensure that the
socket-outlet is located/installed near the equipment and is easily accessible.
ACHTUNG:
Der Netzstecker dient zur sicheren Trennung des Gerätes von der Stromversorgung. Stellen Sie sicher, dass sich die
Steckdose in unmittelbarer Nähe des Gerätes befindet und leicht zugänglich ist.
ATTENTION :
Le cordon d’alimentation doit être débranché pour une mise hors tension totale du produit. La prise de courant
doit être située ou installée à proximité du matériel et être facilement accessible.
Lithium Battery Notice
CAUTION:
Danger of explosion if battery is replaced with incorrect type. Replace only
with the same type recommended by the manufacturer. Dispose of used batteries
according to the manufacturer’s instructions.
according to the manufacturer’s instructions.
ACHTUNG:
Es besteht Explosionsgefahr, wenn die Batterien durch einen falschen Batterientyp ersetzt werden. Ersetzen Sie sie
deshalb nur durch denselben, vom Hersteller empfohlenen Typ. Entsorgen Sie leere Batterien entsprechend den Anweisungen
des Herstellers.
des Herstellers.
ATTENTION :
IIl y a danger d’explosion en cas de remplacement avec le mauvais type de batterie. Remplacer uniquement avec
une batterie du même type recommandé par le constructeur. Les batteries usagées doivent être jetées conformément aux
instructions du fabricant.
instructions du fabricant.
Short Circuit Protection
WARNING:
This product relies on the building’s installation for short-circuit
(overcurrent) protection. Ensure that a fuse or circuit breaker no larger than 120 VAC,
15A U.S. (240 VAC, 10A international) is used on the phase conductors (all current-
carrying conductors).
15A U.S. (240 VAC, 10A international) is used on the phase conductors (all current-
carrying conductors).
WARNUNG:
Dieses Produkt ist darauf angewiesen, dass im Gebäude ein Kurzschluss- bzw. Überstromschutz installiert ist.
Stellen Sie sicher, dass eine Sicherung oder ein Unterbrecher von nicht mehr als 240 V Wechselstrom, 10 A (bzw. in den USA
120 V Wechselstrom, 15 A) an den Phasenleitern (allen stromführenden Leitern) verwendet wird.
120 V Wechselstrom, 15 A) an den Phasenleitern (allen stromführenden Leitern) verwendet wird.
ATTENTION :
La protection contre les courts-circuits (surtension) du produit est assurée par l’installation électrique du local où
il est installé. S’assurer qu’un fusible ou un disjoncteur inférieur ou égal à 120 V CA, 15 A aux Etats-Unis (240 V CA, 10 A
dans les autres pays) est utilisé pour les conducteurs de phase (conducteurs de courant).
dans les autres pays) est utilisé pour les conducteurs de phase (conducteurs de courant).
5
Precautions
F
IGURE
B
Fiery X3eTY2 exploded view
i
Key
1. Cover
2. CPU clamp
3. CPU fan
4. CPU heatsink
5. DIMM
6. CPU
7. Battery
8. Motherboard
9. Interface board
10. Service board cable
11. HDD SATA data cable
12. Power supply
13. HDD bracket
14. HDD (hard disk drive)
15. Exhaust fan
16. Service board
17. Pan
N
OTE
:
The CPU cooling
assembly shown here may differ
from the cooling assembly
installed in your system. For
more information, see page 24.
from the cooling assembly
installed in your system. For
more information, see page 24.
4
1
8
10
9
5
2
3
7
11
12
13
14
15
16
6
17
Click on the first or last page to see other MX-5500N / MX-6200N / MX-7000N (serv.man25) service manuals if exist.