MX-5500N, MX-6200N, MX-7000N (serv.man25). MX- PEX2 SERVICE MANUAL — Sharp Copying Equipment Peripheral (repair manual). Page 46

View Sharp MX-5500N / MX-6200N / MX-7000N (serv.man25) Peripheral online

42
Restoring functionality after service
Restoring functionality after service
Complete your inspection and service by reinstalling and verifying the Fiery X3eTY2.
T
O
 
REINSTALL
 
AND
 
VERIFY
 
THE
 F
IERY 
X3
E
TY2
1.
Reseat all boards, cables, connectors, and other parts loosened or removed during 
service.
When routing cables in the Fiery X3eTY2, verify the following:
Improper connection of the internal power cables can damage the Fiery X3eTY2. See 
“Checking connections” on page 10, which includes Figure G on page 11.
2.
Replace the cover on the Fiery X3eTY2 pan (see Figure F on page 9).
Make sure all cables are low and fully inside the pan before you replace the cover. Align 
the mounting holes in the cover with the holes in the pan.
3.
Secure the cover to the Fiery X3eTY2 pan with the eight screws that you removed earlier.
• Covers are securely installed after 
routing cables
• Cables are not looped around internal 
circuit boards, or components (such as 
capacitors and resistors)
• Cable routing does not interfere with 
the operation of internal components
• Cables do not lie on or against any internal 
heating element
• Cables do not interfere with removing 
or replacing components
• Cables do not interfere with opening or 
closing Fiery X3eTY2 panels 
• Cables are not tangled
• Cable slack is secured with a tie wrap
43
Restoring functionality after service
4.
Mount the Fiery X3eTY2 on the back of the MFP.
Align the slotted holes on the Fiery X3eTY2 with the upper mounting screws attached to 
the MFP (see Figure V). Carefully lower the Fiery X3eTY2 until the narrow ends of the 
slotted holes engage the four mounting screws.
F
IGURE
 V
Mounting the Fiery X3eTY2 on the MFP
5.
Replace the two lower mounting screws that secure the bottom edge of the Fiery X3eTY2 
to the MFP.
6.
Tighten all four mounting screws.
Make sure that the screws are fully tightened and that the Fiery X3eTY2 is firmly 
attached to the MFP.
Upper mounting screw
(1 of 2)
Lower mounting screw
(1 of 2)
Slotted hole (1 of 2)
N
OTE
:
 The exact mounting 
location of the 
Fiery X3eTY2 
on the MFP may differ from 
that shown in this figure.
44
Restoring functionality after service
7.
Connect any external cables that you removed during inspection or service 
(see Figure W).
Make sure that the following cables are properly connected:
• Network cable
• MFP interface cable
• MFP Ethernet cable
F
IGURE
 W
External Fiery X3eTY2 connections
MFP interface connector
MFP Ethernet connector (10/100 BaseT)
Network connector (10/100/1000 BaseT)
Monitor port
(not used, may be covered)
Serial port
(not used, may be covered)
USB-Type A ports
USB-Type B port (not used)
45
Restoring functionality after service
8.
If you installed a new HDD, install system software (see page 50).
A spare HDD is shipped without system software.
9.
Make sure both service switches are in normal position (away from the motherboard).
10.
Power on the MFP using the main power switch inside the front compartment, and then 
the secondary power switch on the Control Panel. Then move the power switch on the 
Fiery X3eTY2 to the ON (|) position. 
Allow the MFP to start up and display ready status on the Control Panel.
11.
Before you leave the customer site, verify Fiery X3eTY2 operation as described in the 
following flow diagram:
F
IGURE
 X
Steps to verify the Fiery X3eTY2
Power up and print test pages
(see page 46).
Check the Setup options (see 
Configuration and Setup on the User 
Documentation CD).
Connect the Fiery X3eTY2 to the 
network and verify (see page 48). 
46
Restoring functionality after service
Printing Fiery X3eTY2 pages
The MFP touch panel allows you to print special pages that reside on the Fiery X3eTY2 
HDD. These pages include the following:
Test Page:
 Verifies that the Fiery X3eTY2 is functional and connected properly to the 
MFP. Print the Test Page before connecting the Fiery X3eTY2 to the network.
Configuration page:
 Lists all the settings in effect from the current Setup. After you 
have finished running Setup, print a Configuration page to confirm your settings. If 
the Fiery X3eTY2 is rebooting, allow the Fiery X3eTY2 to reboot and return to Idle 
before printing a Configuration page.
Before you perform any service procedure, print the Configuration page (if possible) so 
that you can return the settings to their former configurations, if necessary.
After the connection to the network is made, the network administrator can customize 
Setup options according to the network and user environment. Using the 
Configuration page as a guide can help speed up this process.
If desired, you can also print additional Fiery X3eTY2 pages.
T
O
 
PRINT
 F
IERY 
X3
E
TY2 
PAGES
1.
Complete the steps listed below for your MFP model:
MX-7000/6200/5500
MX-4500/3500
• Press the Copy tab on the MFP touch 
panel.
• Press the Fiery icon at the bottom of 
the touch panel.
• Press Fiery Settings.
The Fiery Settings screen appears.
• Press the System Settings button on 
the MFP.
• On the touch panel, press Admin 
Password and then press Password.
• On the touch panel, use the keyboard 
to enter the administrator password for 
the MFP. Press OK and then press OK 
again at the next screen.
This password is not the same as the 
administrator password for the 
Fiery X3eTY2.
• At the System Settings screen, use the 
arrows to scroll to Printer Settings and 
press Printer Settings.
• Press Fiery Settings.
The Fiery Settings screen appears.

Click on the first or last page to see other MX-5500N / MX-6200N / MX-7000N (serv.man25) service manuals if exist.