DOWNLOAD Sharp MX-5500N / MX-6200N / MX-7000N (serv.man25) Service Manual ↓ Size: 2.87 MB | Pages: 99 in PDF or view online for FREE

Model
MX-5500N MX-6200N MX-7000N (serv.man25)
Pages
99
Size
2.87 MB
Type
PDF
Document
Peripheral
Brand
Device
Copying Equipment / MX- PEX2 SERVICE MANUAL
File
mx-5500n-mx-6200n-mx-7000n-sm25.pdf
Date

Sharp MX-5500N / MX-6200N / MX-7000N (serv.man25) Peripheral ▷ View online

 
7
Accessing the Fiery X3eTY2
2.
Make sure that the Fiery Settings screen reads Idle.
 
If Printing, Processing, or RIPping appears, the Fiery X3eTY2 is processing a job, and 
you must wait until the system finishes and reaches Idle state.
 
3.
Press the menu button to display the Functions menu.
4.
Use the down button to scroll to Shut Down. Use the line selection button to select 
Shut Down.
 
The Shut Down menu appears with the following options:
• Restart Server: Resets the Fiery X3eTY2 server software without resetting the 
underlying operating system.
• Shut Down System: Shuts down the Fiery X3eTY2 properly so that you can safely 
power off the Fiery X3eTY2.
• Reboot System: Resets both the Fiery X3eTY2 and the underlying operating system, 
and then reboots the Fiery X3eTY2.
 
5.
Use the line selection button to select Shut Down System.
6.
When a message appears prompting you to check the controller power switch or power 
off the controller, press OK.
7.
Move the power switch on the Fiery X3eTY2 to the Off (O) position (see Figure D).
F
 
IGURE
 
 D
 
Fiery X3eTY2 power panel
 
8.
Power off the MFP using the secondary power switch on the Control Panel, and then the 
main power switch inside the front compartment.
N
 
OTE
 
:
 
If you are recycling power, wait at least five seconds before powering back on.
Service switches
(may be covered)
Power switch
LED display
(may be covered)
Power connector
 
8
Accessing the Fiery X3eTY2
 
T
 
O
 
 
 
ACCESS
 
 
 
AND
 
 
 
OPEN
 
 
 
THE
 
 F
 
IERY 
 
X3
 
E
 
TY2
 
1.
Remove all external cables that are connected to the Fiery X3eTY2.
2.
Loosen the two upper mounting screws that secure the Fiery X3eTY2 to the back of the 
MFP (see Figure E).
 
Loosen, but do not remove, the upper mounting screws.
 
3.
Remove the two lower mounting screws that secure the Fiery X3eTY2 to the MFP.
4.
Lift up to release the Fiery X3eTY2 from the upper mounting screws. Remove the 
Fiery X3eTY2 from the MFP.
F
 
IGURE
 
 E
 
Removing the Fiery X3eTY2 from the MFP
Lift Fiery X3eTY2 to clear 
upper mounting screws. 
Upper mounting screw
(1 of 2)
Lower mounting screw
(1 of 2)
Slotted hole (1 of 2)
N
OTE
:
 The exact mounting 
location of the 
Fiery X3eTY2 
on the MFP may differ from 
that shown in this figure.
 
9
Accessing the Fiery X3eTY2
5.
Place the Fiery X3eTY2 on a flat surface.
6.
Remove the eight screws that secure the cover to the Fiery X3eTY2 pan (see Figure F).
 
Set aside the screws so that you can replace them later.
 
7.
Lift the cover away from the pan, and set aside the cover.
F
 
IGURE
 
 F
 
Opening the Fiery X3eTY2
The Fiery X3eTY2 is now ready for inspection and service.
Screw (1 of 8)
Pan
Cover
 
10
Checking connections
 
Checking connections
 
The most common causes of problems are faulty and loose connections. Before you 
conclude that any internal component has failed, remove, inspect, and reseat all 
appropriate connections, and then verify that the problem still occurs. 
Before you touch any parts inside the Fiery X3eTY2, attach a grounding wrist strap. 
Touching the metal pan also discharges static electricity.
 
T
 
O
 
 
 
CHECK
 
 
 
CABLE
 
 
 
CONNECTIONS
 
1.
Access and open the Fiery X3eTY2 (see page 8).
2.
Place the Fiery X3eTY2 on a flat surface so that internal components are facing up.
3.
Verify that the battery is properly installed (see page 18).
4.
Inspect the HDD data cable to make sure it is intact.
 
Faulty data cables are easily overlooked. Check the contact point between the cable and 
the connector to ensure that they have not separated. If a data cable is suspect, substitute 
it with a tested cable.
 
5.
Check the cables of the exhaust fan and the CPU fan.
 
Make sure that the cables are intact.
 
6.
Check the service board cable.
 
Make sure that the cable is intact and properly connected to the service board and the 
motherboard. For more information, see page 23.
 
7.
Verify that the internal power cables are intact and properly connected to the power 
supply, HDD, motherboard, and Fiery X3eTY2 power switch.
 
Make sure that the black and white wires are properly connected to the correct leads on 
the Fiery X3eTY2 power switch. For more information, see Figure S on page 35.
The following diagram illustrates the internal cable connections between hardware 
components.
Page of 99
Display

Click on the first or last page to see other MX-5500N / MX-6200N / MX-7000N (serv.man25) service manuals if exist.