Sharp MX-5500N / MX-6200N / MX-7000N (serv.man18) Peripheral ▷ View online
MX-FNX4 DISASSEMBLY AND ASSEMBLY 6 – 31
f. Removal of upper door
1) Open the upper door [1], and release the hook [2] at two posi-
1) Open the upper door [1], and release the hook [2] at two posi-
tions.
2) Remove the screw [3], and remove the upper door [1].
g. Removal of buffer roller
1) Remove the buffer roller shaft [2] from the arm [1] at two posi-
1) Remove the buffer roller shaft [2] from the arm [1] at two posi-
tions.
2) Remove the clips [3] at two positions, and remove the two
buffer rollers [4].
(5) Return roller
a. Removal of front cover
1) Open the front cover [1], and remove the clip [2].
2) Lift the front cover [1], and remove it.
* For MX-FNX3, refer to 1-A-(1)-a.
1) Open the front cover [1], and remove the clip [2].
2) Lift the front cover [1], and remove it.
* For MX-FNX3, refer to 1-A-(1)-a.
b. Removal of rear cover
1)
1)
Shift the tray cable cover [1] to the tray side, and remove it.
2)
Remove the six screws [2], and lift and remove the rear cover
[3].
[3].
* For MX-FNX3, refer to 1-A-(2)-a.
c. Removal of saddle inlet front inside cover
1)
1)
Remove the three screws [1], and remove the saddle inlet front
inside cover [2].
inside cover [2].
d. Removal of front inside upper cover
1)
1)
Remove the four screws [1], and remove the front inside upper
cover [2].
cover [2].
* For MX-FNX3, refer to 1-A-(3)-d.
[3]
[1]
[2]
[3]
[3]
[1]
[1]
[2]
[4]
[1]
[2]
[2]
[1]
[3]
[2]
[1]
[2]
[1]
[1]
[2]
[1]
MX-FNX4 DISASSEMBLY AND ASSEMBLY 6 – 32
e. Removal of left upper cover
1) Remove the two screws [1].
2) With the upper door [2] open, tilt the left upper cover [3] to the
1) Remove the two screws [1].
2) With the upper door [2] open, tilt the left upper cover [3] to the
right, and remove it.
CAUTION: When installing, be sure to engage the two pawls [4] of
the left upper cover with the metal plates.
f. Removal of grate-shaped upper guide
1) Move down the tray [1] lower than the grate-shaped upper
1) Move down the tray [1] lower than the grate-shaped upper
guide [2]. (For moving of the tray, refer to "Removal of No. 1
tray.")
tray.")
2) Remove the five screws [3], and remove the grate-shaped
upper guide [2].
g. Removal of No.1 tray
CAUTION: Note for installing or moving the tray
When moving down the tray, push up the shutter [1],
and release the latch [2] on the lower surface of the tray
to lower the tray.
When the latch is released, the tray will free-fall. Hold
the tray with your hand during the removal.
and release the latch [2] on the lower surface of the tray
to lower the tray.
When the latch is released, the tray will free-fall. Hold
the tray with your hand during the removal.
1)
Remove the screw [1], and remove the metal plate [2] and the
slide guide [3]. If the grate-shaped upper guide has been
removed, this procedure is unnecessary.
slide guide [3]. If the grate-shaped upper guide has been
removed, this procedure is unnecessary.
2)
Remove the screw [4], and remove the stopper [5].
[3]
[2]
[1]
[4]
[3]
[2]
[1]
[2]
[1]
[1]
[3]
[2]
[5]
[4]
MX-FNX4 DISASSEMBLY AND ASSEMBLY 6 – 33
3) Remove the two screws [6], and open the harness holder [7] at
three positions. Then, disconnect the connectors [8] at two
positions.
positions.
4) Insert your finger into the hole in the back of the No. 1 tray [9].
Push the tray lift motor gear [10] toward you to release the
clutch, and lift the No. 1 tray [9].
clutch, and lift the No. 1 tray [9].
CAUTION: When the clutch of the tray lift motor gear is released, it
falls by its own weight. When releasing the clutch, there-
fore, hold the tray at the bottom in advance. When
installing it, take care not to twist the tray cable.
fore, hold the tray at the bottom in advance. When
installing it, take care not to twist the tray cable.
h. Removal of No. 2 tray
CAUTION: Note for installing or moving the tray
When moving down the tray, push up the shutter [1],
and release the latch [2] on the lower surface of the tray
to lower the tray.
When the latch is released, the tray will free-fall. Hold
the tray with your hand during the removal.
and release the latch [2] on the lower surface of the tray
to lower the tray.
When the latch is released, the tray will free-fall. Hold
the tray with your hand during the removal.
1)
Remove the screw [1], and remove the stopper [2].
2)
Remove the two screws [3], and disconnect the connector [4].
3)
Insert your finger into the hole in the back of the No. 2 tray [5].
Push the tray lift motor gear [6] toward you to release the
clutch, and lift the No. 2 tray [5].
Push the tray lift motor gear [6] toward you to release the
clutch, and lift the No. 2 tray [5].
CAUTION: When the clutch of the tray lift motor gear is released, it
falls by its own weight. When releasing the clutch, there-
fore, hold the tray at the bottom in advance. When
installing it, take care not to twist the tray cable.
fore, hold the tray at the bottom in advance. When
installing it, take care not to twist the tray cable.
[7]
[8]
[6]
[6]
[9]
[10]
[2]
[1]
[2]
[1]
[4]
[3]
[3]
[5]
[6]
MX-FNX4 DISASSEMBLY AND ASSEMBLY 6 – 34
i. Removal of grate-shaped lower guide
1) Remove the ten screws [1], and remove the grate-shaped
1) Remove the ten screws [1], and remove the grate-shaped
lower guide [2].
CAUTION: When installing, be careful not to damage the grate-
shaped lower guide by hanging it to the sensor flag arm
on the delivery side.
on the delivery side.
j. Removal of stapling tray
1) Remove the snap [1] at four positions, and remove the sensor
1) Remove the snap [1] at four positions, and remove the sensor
flag [3] from the delivery roller [2].
CAUTION: The sensor flag arm is easily broken. When removing it,
hold the base of the snap. When installing, insert the
projection of the sensor flag snap into the hole on the
stapling tray side.
projection of the sensor flag snap into the hole on the
stapling tray side.
2) Remove the E-ring [4], gear [5], parallel pin [6], E-ring [7], and
the bearing [8] in front of the delivery roller.
CAUTION: When the gear [5] is removed, the parallel pin [6] falls.
Be careful not to lose it.
3)
Disconnect all the connectors [9] of the finisher controller PCB.
4)
Remove the four screws [10] to remove the finisher controller
PCB base [11].
PCB base [11].
5)
Release the pawl [13] of the clutch [12] on the back of the
delivery roller, and remove the clutch [12].
delivery roller, and remove the clutch [12].
6)
Remove the E-ring [14] and the bearing [15], and remove the
delivery roller.
delivery roller.
7)
Disconnect the connector [16], and remove the harness from
the clamp and the edge saddle [17].
the clamp and the edge saddle [17].
8)
Remove the two screws [18], and pull out the stapling tray [19]
in the delivery direction.
in the delivery direction.
CAUTION: When removing parts in the stapling tray, do not apply a
force to the alignment plates (front/back) and the three
positions on the rear edge regulation plate.
positions on the rear edge regulation plate.
[1]
[1]
[1]
[2]
[1]
[3]
[2]
[5] [6]
[7] [8]
[4]
[10]
[11]
[9]
[10]
[13]
[14] [15]
[12]
[18]
[17]
[19]
[18]
[16]
Click on the first or last page to see other MX-5500N / MX-6200N / MX-7000N (serv.man18) service manuals if exist.