Sharp MX-5050N / MX-5050V / MX-5070N / MX-5070V / MX-6050N / MX-6050V / MX-6070N / MX-6070V (serv.man4) Service Manual ▷ View online
MX-6070V MX-LC17 N (LARGE CAPACITY TRAY) 5 – 1
MX-6070V
Service Manual
[5] MX-LC17 N (LARGE CAPACITY TRAY)
1. Unpacking
If the connector is removed first, it may be damaged during the instal-
lation procedures. Therefore, keep it packed while un-boxing and
unpack it only when connecting the connector to the machine.
lation procedures. Therefore, keep it packed while un-boxing and
unpack it only when connecting the connector to the machine.
A. Packed items check
2. Installation
Before installation, be sure to turn both the operation and main power
switches off and disconnect the power plug from the power outlet.
Make double sure that the data lamp on the operation panel does not
light up or blink when performing installation.
switches off and disconnect the power plug from the power outlet.
Make double sure that the data lamp on the operation panel does not
light up or blink when performing installation.
A. Release the lock
1)
Remove the paper feed desk fixing screw.
NOTE: Before turning on the power, check to insure that the fixing
screw of the tray is removed. If the power is turned on without
removing the fixing screw, a trouble may be resulted.
removing the fixing screw, a trouble may be resulted.
No.
Name
Quantity
1
Large capacity tray
1
2
Mounting plate upper
2
3
Connecting unit
1
4
Fixing screw A (Hex washer S-tight M4x18)
4
5
Fixing screw B (Hex washer S-tight M4x12)
2
6
Fixing screw C (M4x8 cup)
1
7
LCC Guide sheet
1
2
1
3
4
6
5
7
MX-6070V MX-LC17 N (LARGE CAPACITY TRAY) 5 – 2
B. Main unit and large capacity tray unit connection
1)
Attach the mounting plate upper (Packed item No.2) to the right
side of main unit with the fixing screw A (Packed item No.4).
When installing, put the rubber section (
side of main unit with the fixing screw A (Packed item No.4).
When installing, put the rubber section (
) of the mounting plate
upper on the lower side.
2)
Remove the right door cover from the machine.
3)
Attach the LCC guide sheet (Packed item No.7) onto the paper
entering guide.
entering guide.
Clean surface of the LCC guide sheet with alcohol.
4)
Remove the fixing screws (1 pc) of the machine and remove the
screw cap. And remove the right under cover.
screw cap. And remove the right under cover.
Ĭ
ĭ
Ĭ
ĭ
Attachment position of LCC guide sheet.
Be sure no protruding the tip of the sheet
on the paper transportation guide.
Sectional view.
0mm
0.5mm
0mm
0.5mm
Ĭ
ĭ
MX-6070V MX-LC17 N (LARGE CAPACITY TRAY) 5 – 3
5)
Temporarily fix the fixing screw B (Packed item No.5) midway.
6)
Insert the temporarily fixed screw B into the key hole in the con-
nection unit and temporarily fix the connection unit.
nection unit and temporarily fix the connection unit.
7)
Fix the other fixing screw B and tighten the temporarily fixed
screw B securely.
screw B securely.
8)
Attach the right under cover back to the main unit.
9)
Fix the fixing screw, and attach the screw cap back to the main
unit.
unit.
10) While lifting the section marked with ○ insert the connection unit
into the large capacity tray unit and fix the fixing screw C (Packed
item No.6) at the mark A on the connection unit.
item No.6) at the mark A on the connection unit.
C. Height adjustment
1)
Put the large capacity tray unit closer to the main unit.
Ĭ
ĭ
ĭ
Ĭ
Ĭ
ĭ
Ĭ
Ĭ
ĭ
A
B
MX-6070V MX-LC17 N (LARGE CAPACITY TRAY) 5 – 4
2)
Check to insure that the height adjustment check rib of the large
capacity tray unit and the axis line of the mounting plate upper
mounted to the main unit are in the same line.
capacity tray unit and the axis line of the mounting plate upper
mounted to the main unit are in the same line.
3)
If the height adjustment is not required, insert the large capacity
tray unit further more.
tray unit further more.
If the height adjustment is required, perform the adjustment pro-
cedure from 4).
cedure from 4).
4)
Loosen the adjustment screw on the F side.
NOTE: Use the adjustment screw on the front side for the adjust-
ment. Do not touch the screw on the rear side.
NOTE: If the screw is loosened or removed when servicing, be
sure to execute C Height adjustment after completion of
servicing.
servicing.
5)
In the case of a shift to the right, press the front upper section and
fit the height adjustment check rib so that it is in the same line with
the axis line of the mounting plate upper. Insert the large capacity
tray unit into the main unit.
fit the height adjustment check rib so that it is in the same line with
the axis line of the mounting plate upper. Insert the large capacity
tray unit into the main unit.
6)
In the case of a shift to the left, lift the grid so that the height
adjustment check rib is in the same line with the axis line of the
mounting plate upper and insert the large capacity tray unit.
adjustment check rib is in the same line with the axis line of the
mounting plate upper and insert the large capacity tray unit.
7)
Tighten the loosened screw.
OK
NG
NG
Click on the first or last page to see other MX-5050N / MX-5050V / MX-5070N / MX-5070V / MX-6050N / MX-6050V / MX-6070N / MX-6070V (serv.man4) service manuals if exist.