Sharp MX-4100N / MX-4101N / MX-5000N / MX-5001N (serv.man38) Service Manual ▷ View online
MX-4100N AR-SU1 14 – 3
C. Install the stamp unit (DSPF model)
1)
Open the DSPF unit, remove the OC mat.
2)
Remove the screw, and remove the paper exit PG cover.
Remove the screw.
Disengage the pawl, and remove the stamp case unit.
Remove the screw.
Disengage the pawl, and remove the stamp case unit.
3)
Attach the stamp unit (package part No. 1) to the stamp case
which was removed from the DSPF unit with the installing
screw (package part No. 4). (Fix it together with the earth
wire.)
which was removed from the DSPF unit with the installing
screw (package part No. 4). (Fix it together with the earth
wire.)
* Arrange the harness of the stamp unit as shown below.
4)
Install the stamp case unit, and fasten it with the screw. Install
the earth wire. Connect the connector.
the earth wire. Connect the connector.
5)
Install the paper exit PG cover.
6)
Disengage the pawl, and open the stamp case unit.
Install the stamp cartridge (package part No. 3).
Install the stamp cartridge (package part No. 3).
7)
Install the OC mat to the SPF glass, and close the DSPF unit.
1
2
2
4
3
2
4
1
3
2
1
3
MX-4100N AR-SU1 14 – 4
D. Turn on the power of the main unit
1)
Insert the power plug into the power outlet.
2)
Open the front cabinet of the machine, and turn ON the power
switch.
switch.
3)
Turn ON the power switch on the operation panel.
ON
<State of switch>
ON
OFF
MX-4100N MX-EBX3 15 – 1
MX-4100N
Service Manual
[15] MX-EBX3
1. Unpacking
A. Parts included
2. Installation
A. Turn off the power of the main unit
1)
Turn the power switch located on the operation panel to the
"OFF" position.
"OFF" position.
2)
Open the front cabinet. Turn OFF the power switch in the front
cabinet of the main unit.
cabinet of the main unit.
3)
Disconnect the power plug of the main unit from the power out-
let.
let.
B. Pull out the control PWB
• If cables are connected to the control PWB unit, remove all
cables.
1)
Push the location indicated in the illustration to unlock, and
remove the ozone filter cover from the right rear cabinet.
remove the ozone filter cover from the right rear cabinet.
2)
Remove the screw from the right rear cabinet.
3)
Remove the right rear cabinet.
4)
Remove the two screws from the control PWB unit.
• If the fax box unit is installed, carry out steps 5), 6), and 7)
• If the fax box unit is installed, carry out steps 5), 6), and 7)
additionally.
5)
Pull out the control PWB unit and remove the snap band.
6)
Remove the interface cable from the frame.
7)
Remove the connector.
8)
Pull out and remove the control PWB unit.
No.
Packed part names
Quantity
1
Scanner function expansion PWB (ACRE PWB)
1
1
<State of switch>
ON
OFF
OFF
3
2
4
4
5
8
7
5
6
MX-4100N MX-EBX3 15 – 2
C. Installation of the scanner function expansion
PWB (ACRE PWB)
1)
Remove four screws for fixing the scanner function expansion
PWB (ACRE PWB) from the control PWB.
PWB (ACRE PWB) from the control PWB.
2)
Install the scanner function expansion PWB (ACRE PWB) to
the control PWB by using the four screws for fixing the scanner
function expansion PWB.
Check that the connectors for connecting each PWB are prop-
erly connected.
the control PWB by using the four screws for fixing the scanner
function expansion PWB.
Check that the connectors for connecting each PWB are prop-
erly connected.
D. Reattach the control PWB and the right rear
cabinet
• If the fax box unit is installed, carry out steps 1), 2), and 3)
additionally.
1)
Connect the interface cable to the control PWB unit.
2)
Push the interface cable into the recessed portion of the sheet
metal on the control PWB unit.
metal on the control PWB unit.
3)
Attach the snap band to the sheet metal of the control PWB
unit.
unit.
4)
Push the control PWB unit into the main unit.
5)
Secure the unit with the two screws.
6)
Fit the interface cable into the right rear cabinet cover.
7)
Attach the right rear cabinet cover to the main unit.
At this time, check that the four hooks are properly fitted to the
main unit.
At this time, check that the four hooks are properly fitted to the
main unit.
8)
Secure the right rear cabinet with the screw.
9)
Attach the ozone filter cover to the main unit.
Screws for fixing
the scanner
function expansion
PWB (4 pcs)
Connector
Control PWB
Scanner function expansion PWB
(ACRE PWB)
3
1
2
Hook 1 Hook 2
Hook 3
Hook 4
6
8
7
Click on the first or last page to see other MX-4100N / MX-4101N / MX-5000N / MX-5001N (serv.man38) service manuals if exist.