Sharp MX-3500N / MX-3501N / MX-4500N / MX-4501N (serv.man12) Service Manual ▷ View online
MX3501N ADJUSTMENTS 7 – 9
6)
Load the SPF adjustment pattern on the DSPF.
7)
Press [EXECUTE] key, and scanning of the SPF adjustment
pattern selected in step 2) is started.
pattern selected in step 2) is started.
8)
When [ALL] is selected, load the SPF adjustment pattern on
the DSPF again, and perform the adjustment of the back sur-
face in the similar procedures.
the DSPF again, and perform the adjustment of the back sur-
face in the similar procedures.
9)
The adjustment result screen is displayed.
The value of this time is displayed, and the value of the last
time is displayed in the parenthesis ( ).
The value of this time is displayed, and the value of the last
time is displayed in the parenthesis ( ).
* When [REPRINT] button is pressed, the display returns to
the cassette select screen to allow self-print of the SPF
adjustment pattern (front, back) again.
adjustment pattern (front, back) again.
* When [RESCAN] button is pressed, the SPF adjustment
pattern (front, back) is scanned again.
* When [RETRY] button is pressed, the adjustment value is
not saved in EEPROM and RAM and shifted to the top menu
screen.
screen.
* When [DATA] button is pressed, the data used in execution
of the adjustment are displayed.
10) When [OK] button is pressed, the adjustment value is saved in
EEPROM and RAM and the display is shifted to the end
screen.
screen.
15. Shading adjustment
1)
Fold 2 or 3 sheets of A3 paper (recommendable paper for
color copy) as shown below.
color copy) as shown below.
2)
Open the lower door, place the folded sheets of paper as
shown, and close the lower door.
shown, and close the lower door.
3)
Enter the simulation 63-2 mode.
4)
Select, [DSPF SHADING].
0
SIMULATION NO.50̆28
TEST
AUTO IMAGE POSITION ADJUSTMENT㧦SERVICE
CLOSE
EXECUTE
PLEASE WAIT
NOW EXECUTING…
REPRINT
0
SIMULATION NO.50̆28
TEST
AUTO IMAGE POSITION ADJUSTMENT㧦SERVICE
CLOSE
SPF㧔SIDE1㧕
㧦
LEAD㧖㧖㧔㧖㧖㧕 OFFSET㧦㧖㧖㧔㧖㧖㧕SUB㧦㧖㧖㧔㧖㧖㧕
SPF㧔SIDE2㧕
㧦
LEAD㧖㧖㧔㧖㧖㧕 OFFSET㧦㧖㧖㧔㧖㧖㧕SUB㧦㧖㧖㧔㧖㧖㧕
RETRY
RESCAN
REPRINT
OK
DATA
0
SIMULATION NO.50̆28
TEST
AUTO IMAGE POSITION ADJUSTMENT㧦SERVICE
CLOSE
SIMULATION COMPLETE
PLEASE PUSH CA KEY
1/1
1
A3
320mm
279mm
2
15mm
10
1
2
SIMULATION NO.63 02
TEST
SHADING EXECUTION
EXECUTE
0
CLOSE
PRESS [EXECUTE] TO SHADING START
SIMULATION NO.63 02
TEST
SHADING EXECUTION
EXECUTE
0
CLOSE
SELECT OC SHADING/DSPF SHADING, AND PRESS EXECUTE
OCSHADING
DSPFSHADING
MX3501N ADJUSTMENTS 7 – 10
5)
When [EXECUTE] button is pressed, it is highlighted and
shading is started.
* During execution, "SHADING EXECUTING..." is displayed.
* When [EXECUTE] button is pressed during execution, the
shading is started.
* During execution, "SHADING EXECUTING..." is displayed.
* When [EXECUTE] button is pressed during execution, the
operation is interrupted.
* When shading is completed normally, [EXECUTE] button
returns to the normal display and "COMPLETED" is dis-
played.
played.
* When [SYSTEM SETTINGS] key is pressed during other
than printing, the display returns to the sub number entry
screen.
screen.
<Descriptions of buttons>
<Result display>
16. CCD gamma adjustment (CCD
calibration)
This adjustment is required in the following cases:
* When the CCD unit is replaced.
* When a U2 trouble occurs.
* When the scanner control PWB is replaced.
* When the EEPROM on the scanner control PWB is replaced.
* When the CCD unit is replaced.
* When a U2 trouble occurs.
* When the scanner control PWB is replaced.
* When the EEPROM on the scanner control PWB is replaced.
A. Note before adjustment
1)
Check to insure that there is no dirt or dust on the SPF scan-
ning glass, the mirror, and the lens surface. (If there is, clean it
with alcohol.)
ning glass, the mirror, and the lens surface. (If there is, clean it
with alcohol.)
2)
Check to confirm that the patches in BK1 and BK2 arrays of
the SIT chart (UKOG-0280FCZZ or UKOG-0280FCZ1) are
free from dirt and scratches.
If they are dirty, clean them.
If they are scratched or streaked, replace with new one.
NOTE:
Since the SIT chart (UKOG-0280FCZZ) is easily discolored by
sunlight (especially ultraviolet rays) and humidity and tempera-
ture, put it in a bag such as a clear file) and store in a dark
place of low temperature and low humidity.
the SIT chart (UKOG-0280FCZZ or UKOG-0280FCZ1) are
free from dirt and scratches.
If they are dirty, clean them.
If they are scratched or streaked, replace with new one.
NOTE:
Since the SIT chart (UKOG-0280FCZZ) is easily discolored by
sunlight (especially ultraviolet rays) and humidity and tempera-
ture, put it in a bag such as a clear file) and store in a dark
place of low temperature and low humidity.
B. Adjustment procedures
1)
Set the SIT chart (UKOG-0280FCZZ or UKOG-0280FCZ1)
face-down in the DSPF paper feed tray.
face-down in the DSPF paper feed tray.
If the SIT chart is not available, execute SIM 63-5 to set the
CCD gamma to the default. In this case, however, the adjust-
ment accuracy is lower when compared with the adjustment
method using the SIT chart.
NOTE: UKOG-0280FCZZ is equivalent to UKOG-0280FCZ1.
CCD gamma to the default. In this case, however, the adjust-
ment accuracy is lower when compared with the adjustment
method using the SIT chart.
NOTE: UKOG-0280FCZZ is equivalent to UKOG-0280FCZ1.
2)
Enter the SIM 63-03 mode.
3)
When a color button is selected, the adjustment value of the
selected color is displayed.
* When [B] (Blue), [G] (Green), or [R] (Red) button is selected,
selected color is displayed.
* When [B] (Blue), [G] (Green), or [R] (Red) button is selected,
the selected button is highlighted and the adjustment value
of the selected color is displayed.
of the selected color is displayed.
* Only one color button can be selected, and the selected but-
ton is highlighted. In the initial state, [B] is selected.
* If there is a page over [
↑], an active display is shown and the
page moves up. If there is no page upward, the display
grays out and the operation is invalid.
If there is a page under [
grays out and the operation is invalid.
If there is a page under [
↓], an active display is shown and
the page moves down. If there is no page downward, the
display grays out and the operation is invalid.
display grays out and the operation is invalid.
Display
Content
OC
SHADING
SHADING
OC analog correction level correction, and shading
correction data making (Document table mode)
correction data making (Document table mode)
DSPF
SHADING
SHADING
DSPF analog correction level correction, and shading
correction data making (SPF mode)
correction data making (SPF mode)
Display
Content
COMPLETE
Normal completion
ERROR
Abnormal completion
INCOMPLETE
Incomplete, interruption
CLOSE
OC
SIMULATION NO.63㧙03
TEST
SCANNER COLOR BALANCE AUTO ADJUSUTMENT
OC #1:197, #2:185, #3:165, #4:148, #5:117, #6:110,
#7: 88, #8: 75, #9: 55, #10: 45, #11: 38, #12: 29,
#19: 5, #20: 4, #22: 2, #:24: 2
#13: 27, #14: 21, #15: 18, #:16:15, #17: 10, #18: 8,
0
1/4
DSPF
B
G
R
CLOSE
OC
SIMULATION NO.63㧙03
TEST
SCANNER COLOR BALANCE AUTO ADJUSUTMENT
OC #1:197, #2:185, #3:165, #4:148, #5:117, #6:110,
#7: 88, #8: 75, #9: 55, #10: 45, #11: 38, #12: 29,
#19: 5, #20: 4, #22: 2, #:24: 2
#13: 27, #14: 21, #15: 18, #:16:15, #17: 10, #18: 8,
0
1/4
DSPF
B
G
R
MX3501N ADJUSTMENTS 7 – 11
4)
When [DSPF] button is pressed, it is highlighted, and the color
automatic adjustment execution screen is displayed.
automatic adjustment execution screen is displayed.
5)
Press [EXECUTE] button and it is highlighted and the color
auto adjustment is executed.
* When [EXECUTE] button is pressed during the automatic
auto adjustment is executed.
* When [EXECUTE] button is pressed during the automatic
adjustment, the automatic adjustment is interrupted.
6)
After normal completion, the result of calculation is displayed
in the initial screen.
in the initial screen.
* When an error occurs in execution, the following screen is dis-
played.
When [CA] key is pressed, the simulation is terminated. When
[SYSTEM SETTINGS] key is pressed, the display returns to the
sub number entry screen.
When [CA] key is pressed, the simulation is terminated. When
[SYSTEM SETTINGS] key is pressed, the display returns to the
sub number entry screen.
* When an error occurs in the automatic adjustment, all the error
patch numbers are displayed.
When [RESULT] button is pressed, the display returns to the ini-
tial screen. (The previous value is displayed)
When [RESULT] button is pressed, the display returns to the ini-
tial screen. (The previous value is displayed)
* When the operation is completed normally, "COMPLETE" is dis-
played. When [RESULT] button is pressed, the display returns to
the initial screen. (The calculation result of normal completion is
displayed.)
the initial screen. (The calculation result of normal completion is
displayed.)
SIMULATION NO.63㧙03
TEST
SCANNER COLOR BALANCE AUTO ADJUSUTMENT
SET THE CHART ON DSPF AND TOUCH [EXECUTE]
SET THE CHART ON DSPF AND TOUCH [EXECUTE]
0
1/1
CLOSE
EXECUTE
SIMULATION NO.63㧙03
TEST
SCANNER COLOR BALANCE AUTO ADJUSUTMENT
NOW CHART PATCH READING…
0
1/1
CLOSE
EXECUTE
SIMULATION NO.63㧙03
TEST
SCANNER COLOR BALANCE AUTO ADJUSUTMENT
SCANNER MOTOR IS NOT READY
0
1/1
CLOSE
EXECUTE
SIMULATION NO.63㧙03
TEST
SCANNER COLOR BALANCE AUTO ADJUSUTMENT
SAMPRING DATA UNFIT
SAMPRING DATA UNFIT
#1, #2, #3, #4, #5, #6, #7, #8, #9, #10, #11, #12, #13, #14, #15,
PLEASE CHECK THE CHART AND PLATEN GLASS
#16, #17, #18, #19, #20, #22, #24
0
RESULT
B
G
R
1/1
CLOSE
SIMULATION NO.63㧙03
TEST
SCANNER COLOR BALANCE AUTO ADJUSUTMENT
COMPLETE
0
RESULT
B
G
R
1/1
CLOSE
MX3501N SELF DIAG AND TROUBLE CODE 8 – 1
MX3501N
Service Manual
[8] SELF DIAG AND TROUBLE
CODE
1. Trouble code and troubleshooting
E6-10 Back-face shading trouble (black
correction)
E6-11
Shading trouble (white correction)
E6-14 Back-face SCAN-ASIC trouble
U5-00 SPF communication trouble
U5-16 SPF fan motor trouble
U5-30 SPF lift-up trouble
U5-31 SPF tray lift-down trouble
U5-40 SPF install trouble
Trouble content
CCD black scan level abnormality when the copy
lamp is turned off.
lamp is turned off.
Section
Scanner
Case 1
Cause
Installation error of the CCD unit harness
Check and
remedy
remedy
Check the installing state of the harness to the
CCD unit.
CCD unit.
Case 2
Cause
CCD unit abnormality
Check and
remedy
remedy
Check the CCD unit.
Case 3
Cause
SCU PWB abnormality
Check and
remedy
remedy
Check the SCU PWB.
Trouble content
CCD white scan level abnormality when the copy
lamp is on.
lamp is on.
Section
Scanner
Case 1
Cause
Installation error of the CCD unit harness
Check and
remedy
remedy
Check the installing state of the harness to the
CCD unit.
CCD unit.
Case 2
Cause
Copy lamp lighting trouble
Check and
remedy
remedy
Check the installing state of the harness to the
copy lamp unit.
copy lamp unit.
Case 3
Cause
CCD unit abnormality
Optical axis abnormality
Optical axis abnormality
Check and
remedy
remedy
Check the CCD unit.
In case of an optical axis abnormality, E6-11 may
be canceled by turning the black screw in front of
the lens half-turn clockwise or counterclockwise.
In case of an optical axis abnormality, E6-11 may
be canceled by turning the black screw in front of
the lens half-turn clockwise or counterclockwise.
Case 4
Cause
DSPF PWB abnormality
Check and
remedy
remedy
Check the DSPF PWB.
Case 5
Cause
Dirt on the mirror, the lens, or the reference white
plate.
plate.
Check and
remedy
remedy
Clean the mirror, the lens, or the reference white
plate.
plate.
Trouble content
Written register value cannot be read correctly
Section
Scanner
Case 1
Cause
SCU PWB abnormality
Check and
remedy
remedy
Check the SCU PWB.
Trouble content
Communication error between the SCU and the
DSPF, communication line test error after turning
on the power or canceling the exclusive simulation
DSPF, communication line test error after turning
on the power or canceling the exclusive simulation
Section
Scanner
Case 1
Cause
Malfunction due to electrical noises
Check and
remedy
remedy
Cancel the trouble by turning OFF/ON.
Case 2
Cause
Connector and harness connection trouble or
disconnection
disconnection
Check and
remedy
remedy
Check the connector and the harness of the
communication line.
communication line.
Case 3
Cause
Control (SCU) PWB trouble. DSPF PWB trouble
Check and
remedy
remedy
Replace the control (SCU) PWB. Replace the
DSPF PWB.
DSPF PWB.
Trouble content
The motor lock signal is detected during rotation of
the fan.
the fan.
Section
Scanner
Case 1
Cause
Fan motor trouble,harness of the fan motor related,
circuit trouble
circuit trouble
Check and
remedy
remedy
Use SIM2-3 to check the operation.
Check harness, connector and fan motor related
circuit.
Check harness, connector and fan motor related
circuit.
Trouble content
Lift-up trouble is detected 5 times continuously.
Section
Scanner
Case 1
Cause
STUD/STLD trouble
Check and
remedy
remedy
Check STUD/STLD and its harness and connector.
Check the lift-up unit.
Check the lift-up unit.
Trouble content
Lift-down trouble (STLD does not turn OFF within
the specified time.)
the specified time.)
Section
Scanner
Case 1
Cause
STUD/STLD trouble
Check and
remedy
remedy
Check STUD/STLD and its harness and connector.
Check the lift-up unit.
Check the lift-up unit.
Trouble content
Detected the installed (individual installed signal)
of RSPF/DSPF both.
of RSPF/DSPF both.
Section
Scanner
Case 1
Cause
Circuit trouble of the installed detection signal
Check and
remedy
remedy
Check installed detection circuit and harness,
connector.
connector.
Click on the first or last page to see other MX-3500N / MX-3501N / MX-4500N / MX-4501N (serv.man12) service manuals if exist.