Sharp MX-3050N / MX-3060N / MX-3070N / MX-3550N / MX-3560N / MX-3570N / MX-4050N / MX-4060N / MX-4070N (serv.man5) Service Manual ▷ View online
MX-4070N EXTERNAL VIEW AND INTERNAL STRUCTURE 4 – 24
15. Fuses and thermostats
Signal name
Name
Type
Section
F1
Fuse
20A 250V
AC PWB (For 100V series)
F1
Fuse
10A 250V
AC PWB (For 200V series)
F2
Fuse
10A 250V
AC PWB (For 200V series)
F101
Fuse
12A 250V
DC Power PWB
F102
Fuse
2A 250V
DC Power PWB
F301
Fuse
5A 250V
DC Power PWB
F401
Fuse
3.15A 250V
DC Power PWB
F601
Fuse
6.3A 250V
DC Power PWB
F602
Fuse
6.3A 250V
DC Power PWB
F603
Fuse
6.3A 250V
DC Power PWB
F604
Fuse
6.3A 250V
DC Power PWB
F605
Fuse
6.3A 250V
DC Power PWB
Signal name
Name
Type
Function and Operation
TS LM
Thermostat
Mechanical thermostat
Shuts down the heater lamp (HL_LM) circuit when the fusing section is overheated
TS UM
Thermostat
Mechanical thermostat
Shuts down the heater lamp (HL_UM) circuit when the fusing section is overheated (center section)
TS US
Thermostat
Mechanical thermostat
Shuts down the heater lamp (HL_US) circuit when the fusing section is overheated (edge section)
TS LM
TS UM
TS US
DC PWB
AC PWB
F2
F1
F101
F102
F301
F601
F401
F602
F603
F604
F605
MX-4070N ADJUSTMENTS AND SETTINGS 5 – 1
MX-4070N
Service Manual
[5] ADJUSTMENTS AND SETTINGS
1. General
Each adjustment item in the adjustment item list is associated with
a specific Job number. Perform the adjustment procedures in the
sequence of Job numbers from the smallest to the greatest.
However, there is no need to perform all the adjustment items.
Perform only the necessary adjustments according to the need.
a specific Job number. Perform the adjustment procedures in the
sequence of Job numbers from the smallest to the greatest.
However, there is no need to perform all the adjustment items.
Perform only the necessary adjustments according to the need.
Unnecessary adjustments can be omitted. Even in this case how-
ever the sequence from the smallest to the greatest Job number
must be observed.
If the above precaution should be neglected, the adjustment would
not complete normally or trouble may occur.
ever the sequence from the smallest to the greatest Job number
must be observed.
If the above precaution should be neglected, the adjustment would
not complete normally or trouble may occur.
2. Adjustment item list
Job No.
Adjustment item list
Simulation
ADJ 1
Developing unit adjustment
1-A
Toner density control reference value setting
25-2
ADJ 2
High voltage values adjustment
2-A
Main charger grid voltage adjustment
8-2
2-B
Developing bias voltage adjustment
8-1
2-C
Transfer current and voltage adjustment
8-6
ADJ 3
Image density sensor
adjustment
adjustment
3-A
Image density sensor adjustment
44-2
ADJ4
Print image position, image
magnification ratio adjustment
(Print engine) (Manual
adjustment)
magnification ratio adjustment
(Print engine) (Manual
adjustment)
4-A
Print image magnification ratio adjustment (main scanning direction) (Print engine) (Manual
adjustment)
adjustment)
50-10
4-B
Print image position (main scanning direction, sub scanning direction adjustment, (Print
engine) (Manual adjustment)
engine) (Manual adjustment)
50-10
ADJ5
Print engine image distortion
adjustment, OPC drum phase
adjustment, Color registration
adjustment (Print engine
section)
adjustment, OPC drum phase
adjustment, Color registration
adjustment (Print engine
section)
5-A
Print engine image distortion adjustment (Manual adjustment), OPC drum phase adjustment
(Automatic adjustment), Color registration adjustment (Automatic adjustment)
(Automatic adjustment), Color registration adjustment (Automatic adjustment)
50-22
5-B
Print engine image skew (LSU skew) adjustment (Manual adjustment) (No need to adjust
normally)
normally)
50-20
(64-1)
5-C
Color registration offset adjustment (No need to adjust normally)
50-20
ADJ6
Scan image distortion
adjustment (Document table
mode)
adjustment (Document table
mode)
6-A
Scanner (reading) unit parallelism adjustment (sub scanning direction distortion adjustment)
6-B
Scan image (main scanning direction) distortion adjustment
ADJ7
Scanner image skew
adjustment (DSPF/RSPF
mode)
adjustment (DSPF/RSPF
mode)
7-A
RSPF scan image skew adjustment
7-B
DSPF parallelism adjustment
7-C
DSPF skew adjustment (front surface mode)
7-D
DSPF skew adjustment (back surface mode)
ADJ8
Scan image focus adjustment
8-A
Image focus adjustment (document table mode, DSPF/RSPF front surface mode)
48-1
8-B
Image focus adjustment (DSPF back surface mode)
ADJ9
Scan image magnification ratio
adjustment (Manual
adjustment)
adjustment (Manual
adjustment)
9-A
Scan image magnification ratio adjustment (main scanning direction) (Manual adjustment)
48-1
9-B
Scan image magnification ratio adjustment (main scanning direction) (Manual adjustment)
(Document table mode)
(Document table mode)
48-1
9-C
Scan image magnification ratio adjustment (main scanning direction) (Manual adjustment)
(DSPF/RSPF mode)
(DSPF/RSPF mode)
48-1
9-D
Scan image magnification ratio adjustment (sub scanning direction) (Manual adjustment)
(DSPF/RSPF mode)
(DSPF/RSPF mode)
48-1
ADJ10
Scan image off-center
adjustment (Manual
adjustment)
adjustment (Manual
adjustment)
10-A
Scan image off-center adjustment (Manual adjustment) (Document table mode)
50-12
10-B
Scan image off-center adjustment (Manual adjustment) (DSPF/RSPF mode)
50-12/50-6
ADJ11
Copy image position, image
loss adjustment (Manual
adjustment)
loss adjustment (Manual
adjustment)
11-A
Copy image position, image loss (Manual adjustment) (Document table mode)
50-1
11-B
Image scanning position adjustment (Manual adjustment) (DSPF/RSPF mode)
53-8
11-C
Copy image position, image loss (Manual adjustment) (DSPF/RSPF mode)
50-6
ADJ12
Print lead edge image position adjustment (printer mode)
50-5
ADJ13
FR density variation correction
13-A
FR density unevenness automatic correction
61-11
13-B
FR density unevenness visual inspection correction
61-12
ADJ14/
SET1
Color balance and density
adjustment
adjustment
Note before execution of the image quality adjustment
Copy image quality check
Printer image quality check
Copy image quality check
Printer image quality check
14-A
Scanner calibration
14-A
(1)
Scanner calibration (CCD calibration) (document table
mode)
mode)
63-3
14-A
(2)
Shading adjustment (DSPF mode)
63-2
14-A
(3)
Scanner calibration (CCD calibration) (DSPF mode)
63-3
SET
1
Color balance
adjustment target setup
adjustment target setup
1A
Copy color balance adjustment target setup
63-7/8/11
1B
Printer color balance adjustment target setup
67-26/27/
28
14-B
Copy, printer color balance and density adjustment (Automatic adjustment) (Basic
adjustment)
adjustment)
46-74
3
: ‘17/July
3
MX-4070N ADJUSTMENTS AND SETTINGS 5 – 2
ADJ14/
SET1
Color balance and density
adjustment
adjustment
14-C
Copy image quality
adjustment (Basic
adjustment)
adjustment (Basic
adjustment)
14-C
(1)
Copy color balance and density adjustment (Automatic
adjustment)
adjustment)
46-24
14-C
(2)
Copy color balance and density adjustment (Manual
adjustment)
adjustment)
46-21
14-D
Copy, Image send, FAX
image quality adjustment
(Individual adjustment)
image quality adjustment
(Individual adjustment)
14-D
(1)
Color copy density adjustment (for each color copy
mode) (separately for the low density area and the high
density area) (No need to adjust normally)
mode) (separately for the low density area and the high
density area) (No need to adjust normally)
46-1
14-D
(2)
Monochrome copy density adjustment (for each
monochrome copy mode) (separately for the low density
area and the high density area) (No need to adjust
normally)
monochrome copy mode) (separately for the low density
area and the high density area) (No need to adjust
normally)
46-2
14-D
(3)
Color copy color balance, gamma adjustment (for each
color copy mode) (No need to adjust normally)
color copy mode) (No need to adjust normally)
46-10
14-D
(4)
Monochrome copy density, gamma adjustment (for each
monochrome copy mode) (No need to adjust normally)
monochrome copy mode) (No need to adjust normally)
46-16
14-D
(5)
Automatic monochrome (Copy/scan/FAX) mode
document density scanning operation (exposure
operation) conditions setting (No need to set normally)
document density scanning operation (exposure
operation) conditions setting (No need to set normally)
46-19
14-D
(6)
Document low density image density reproduction
adjustment in the automatic monochrome (copy/scan/
FAX) mode (No need to adjust normally) (Background
density adjustment in the scanning section)
adjustment in the automatic monochrome (copy/scan/
FAX) mode (No need to adjust normally) (Background
density adjustment in the scanning section)
46-32
14-D
(7)
Copy, scan low density image density adjustment (for
each mode) (No need to adjust normally)
each mode) (No need to adjust normally)
46-63
14-D
(8)
Color copy, text, line image reproduction adjustment
(edge gamma, density adjustment) (Text, Map mode)
(No need to adjust normally)
(edge gamma, density adjustment) (Text, Map mode)
(No need to adjust normally)
46-27
14-D
(9)
Monochrome (Copy/scan/FAX) mode color document
reproduction adjustment (No need to adjust normally)
reproduction adjustment (No need to adjust normally)
46-37
14-D
(10)
Color copy mode dark area gradation (black component
quantity) adjustment (No need to adjust normally)
quantity) adjustment (No need to adjust normally)
46-38
14-D
(11)
Color (copy/scan) mode sharpness adjustment (No
need to adjust normally)
need to adjust normally)
46-60
14-D
(12)
Copy high density image density reproduction setting
(Normally unnecessary to the setting change)
(Normally unnecessary to the setting change)
46-23
14-D
(13)
Copy color balance adjustment (single color copy mode)
(No need to adjust normally)
(No need to adjust normally)
46-25
14-D
(14)
DSPF/RSPF mode (copy/scan/FAX) density adjustment
(No need to adjust normally)
(No need to adjust normally)
46-9
14-D
(15)
Copy gamma, color balance adjustment for each dither
(Automatic adjustment)
(Automatic adjustment)
46-54
14-D
(16)
Dropout color adjustment (Normally not required)
46-55
14-D
(17)
Watermark adjustment (Normally not required)
46-66
14-E
Printer image quality
adjustment (Basic
adjustment)
adjustment (Basic
adjustment)
14-E
(1)
Printer color balance adjustment (Automatic adjustment)
67-24
14-E
(2)
Printer color balance adjustment (Manual adjustment)
67-25
14-F
Printer image quality
adjustment (Individual
adjustment)
adjustment (Individual
adjustment)
14-F
(1)
Printer density adjustment (low density section density
adjustment) (No need to adjust normally)
adjustment) (No need to adjust normally)
67-36
14-F
(2)
Printer high density image density reproduction setting
(supporting the high density section tone gap) (No need
to adjust normally)
(supporting the high density section tone gap) (No need
to adjust normally)
67-34
14-F
(3)
Printer gamma adjustment for each dither (Automatic
adjustment) (No need to adjust normally)
adjustment) (No need to adjust normally)
67-54
ADJ15
Paper size sensor adjustment
15-A
Manual paper feed tray paper size (width) sensor adjustment
40-2
15-B
DSPF/RSPF paper feed tray document size (width) sensor adjustment
53-6
ADJ16
Document size detection
adjustment
adjustment
16-A
Sensitivity adjustment of the original size sensor
41-2
ADJ17
Touch panel coordinate setting
65-1
ADJ18
Fusing paper guide position adjustment
Job No.
Adjustment item list
Simulation
3
: ‘17/July
3
MX-4070N ADJUSTMENTS AND SETTINGS 5 – 3
3. Details of adjustment
ADJ 1
Developing unit adjustment
1-A
Toner density control reference value
setting
setting
This adjustment must be performed in the following cases.
• When developer is replaced
• When developer is replaced
Be sure to execute this adjustment only when developer is
replaced. Never execute it in the other cases.
replaced. Never execute it in the other cases.
Perform the toner density reference control level adjustment with
the toner cartridges removed.
If adjustment is performed with toner cartridge installed, the EE-EL
trouble code or an over toner condition may occur.
1) With the front cover opened, enter Sim25-2
2) Close the front cover
3) Select a developing unit to be adjusted
4) When [EXECUTE] key is pressed, it is highlighted. The DV
the toner cartridges removed.
If adjustment is performed with toner cartridge installed, the EE-EL
trouble code or an over toner condition may occur.
1) With the front cover opened, enter Sim25-2
2) Close the front cover
3) Select a developing unit to be adjusted
4) When [EXECUTE] key is pressed, it is highlighted. The DV
roller rotates and the toner density sensor detects toner den-
sity and the output value is displayed.
The above operation is executed for 1 minutes and the aver-
age value of the toner density sensor detection level is set
(saves) as the reference toner density control value.
When the reference toner density control adjustment operation
is completed [EXECUTE] key returns to normal from highlight.
This makes known about whether the adjustment operation is
completed or not.
The above operation is executed each of the lower speed
mode and the middle speed mode and the reference toner
density control value is set for each of them.
sity and the output value is displayed.
The above operation is executed for 1 minutes and the aver-
age value of the toner density sensor detection level is set
(saves) as the reference toner density control value.
When the reference toner density control adjustment operation
is completed [EXECUTE] key returns to normal from highlight.
This makes known about whether the adjustment operation is
completed or not.
The above operation is executed each of the lower speed
mode and the middle speed mode and the reference toner
density control value is set for each of them.
If the operation is interrupted within 1 minutes the adjustment
result is not reflected.
When [EXECUTE] key is pressed during the operation, the
operation is stopped and [EXECUTE] key returns to the normal
display.
If [EE-EU], [EE-EL] or [EE-EC] is displayed, setting of the ref-
erence toner density control value is not completed normally.
Troubleshoot the cause, remove the cause and perform setting
again.
result is not reflected.
When [EXECUTE] key is pressed during the operation, the
operation is stopped and [EXECUTE] key returns to the normal
display.
If [EE-EU], [EE-EL] or [EE-EC] is displayed, setting of the ref-
erence toner density control value is not completed normally.
Troubleshoot the cause, remove the cause and perform setting
again.
5) Cancel Sim 25-2
6) Confirm that "Instal the toner cartridge " is displayed and instal
6) Confirm that "Instal the toner cartridge " is displayed and instal
the toner cartridge by the following procedures
7)
Shake the toner cartridge horizontally several times
8)
Open the front cover and insert each toner cartridge
Be sure to install the color cartridge to their proper positions.
Avoid installation to a different color position.
Avoid installation to a different color position.
Do not forcibly insert the toner cartridge.
Push it in until the cartridge is securely locked in place.
Push it in until the cartridge is securely locked in place.
Developing units removed, be sure to remove the toner car-
tridges as well to prevent toner clogging.
tridges as well to prevent toner clogging.
Mounting location of the toner cartridge of each color
9)
Close the front cover
10) Confirm that "Toner replacement in progress" is displayed and
wait until the display disappears (It takes 30 sec - 6 min)
This procedure is for checking the toner supply operation from
the toner cartridge to the DV unit. The operation time differs
depending on the toner quantity in the toner cartridge, uneven
distribution of toner and the internal state of the toner car-
tridge.
the toner cartridge to the DV unit. The operation time differs
depending on the toner quantity in the toner cartridge, uneven
distribution of toner and the internal state of the toner car-
tridge.
Error display
Error name
Details of error
EE-EL
EL abnormality
Sensor output level less than 77 or
control voltage over 207
control voltage over 207
EE-EU
EU abnormality
Sensor output level over 177 or
control voltage less than 52
control voltage less than 52
EE-EC
EC abnormality
Sensor output level other than 128
10
Click on the first or last page to see other MX-3050N / MX-3060N / MX-3070N / MX-3550N / MX-3560N / MX-3570N / MX-4050N / MX-4060N / MX-4070N (serv.man5) service manuals if exist.